Advertisement
Quick Links
ASSEMBLY INSTRUCTION
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE
PARTS LIST
PART
MATERIAL
NO.
CODE
1
KUS3200-CS01
2
KUS3200-CS02
3
62KUS3200X103
4
62KUS3200X102
5
KUS3200-CS03
6
KUS3200-CS04
7
KUS3200-CS05
8
17TAN00042
9
17TAN00043
!
Do not discard any of the packaging until you have checked that you have all the parts and pack of
fittings.
!
Keep children away during assembly. This item contains small parts which can be swallowed by
children. Children should always be under direct adult supervision while using the product.
!
Retain the assembly instructions for future reference.
UBERHAUS
GRILL GAZEBO
RONA CODE: 79275000
ITEM NUMBER: 10S880A
INTENDED FOR RESIDENTIAL USE ONLY.
PART
LEG A
LEG B
SHORT SUPPORT
LONGER SUPPORT
SHORT CANOPY SUPPORT BRACE
LONGER CANOPY SUPPORT BRACE
CANOPY FRAME CONNECTOR
METAL CONNECTOR A
METAL CONNECTOR B
10
Q'TY
KUS3200-CS06
2
11
17ICA051601--Y3
2
12
17C33A0709001Y4
2
13
17C33A0706001Y4
2
14
17C17A0403001Y4
4
15
17FA05040301-Y4
4
16
1800337004
2
17
17KAA0101----Y4
2
18
KUS3200-CS07
2
19
KUS3200-CS08
PAGE 1 OF 7
TABLE TOP
PEG
BOLT M6*25
BOLT M6*16
SCREW ST4.2*12
WASHER d6.5*D13*1.0
BOLT CAP
HEX.KEY WRENCH 4MM
SMALL CANOPY
LARGE CANOPY
COURTYARD CREATIONS INC.
2
4
16
16
4
32
32
1
1
1
Advertisement
Related Manuals for Uberhaus 10S880A
Summary of Contents for Uberhaus 10S880A
- Page 1 UBERHAUS ASSEMBLY INSTRUCTION GRILL GAZEBO RONA CODE: 79275000 ITEM NUMBER: 10S880A ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE INTENDED FOR RESIDENTIAL USE ONLY. PARTS LIST PART MATERIAL PART Q’TY KUS3200-CS06 CODE TABLE TOP KUS3200-CS01 17ICA051601--Y3 LEG A KUS3200-CS02 17C33A0709001Y4...
- Page 2 Attention: FIGURE 1 Make sure that each bolt needed for all steps match the corresponding figure to ensure proper assembly. Step 1: Fasten one short support (#3) to the legs (#1 and #2) by using bolts (#12) and washers (#15). Tighten all the bolts.
- Page 3 Step 3: FIGURE 3 Fasten the metal connectors (#8 and #9) to the legs (#1 and #2) by using bolts (#13) and washers (#15). Tighten all the bolts. See Figure 3. NOTE: Make sure that the labelled arrows on the metal connectors (#8 and #9) are facing outside.
- Page 4 FIGURE 5 Step 5: Insert the longer canopy support braces (#6) into the canopy frame connector (#7). See Figure 5 – Step 1. Step 1 Step 2 Step 6: Place the large canopy (#19) onto the assembled canopy frame. Then insert the ends of the longer canopy support braces (#6) into the pockets of the large canopy (#19).
- Page 5 Step 7: FIGURE 6 Insert the short canopy support braces (#5) into the canopy frame connector (#7). See Figure 6 – Step 1. Step 1 Step 8: Step 2 Place the small canopy (#18) onto the assembled canopy frame. Then insert the ends of the short canopy support braces (#5) into the pockets of the small canopy (#18).
- Page 6 Step 9: FIGURE 7 Insert the small canopy assemlbly onto the large canopy assembly. Fasten them together by using screws (#14). See Figure 7. Step 1 Step 2 FIGURE 8 Step 10: Insert the canopy assembly onto the legs (#1 and #2). Then fasten the canopy belts to the supports.
- Page 7 Step 11: FIGURE 9 Stick the pegs (#11) into the ground and hook the pegs (#11) through the metal spacer’s holes correctly. See Figure 9. Step 12: Re-check and re-tighten all bolts and cover them with bolts caps (#16). Cleaning and Maintenance •...