Ubiquiti EdgeSwitch 5XP Quick Start Manual
Hide thumbs
Also See for EdgeSwitch 5XP:
- Quick start manual (12 pages) ,
- Quick start manual (21 pages)
Table of Contents
Advertisement
ES-5XP Quick Start Guide
Package Contents
EdgeSwitch 5XP
Screws (Qty. 2)
Anchors (Qty. 2)
Power Adapter (24V, 2.5A)
Power Cord
Installation Requirements
Drill, 6 mm drill bit, and Phillips screwdriver (wall-mounting)
For outdoor applications, shielded Category 5 (or above) cabling should be used for all
wired Ethernet connections and should be grounded through the AC ground of the power
supply.
We recommend that you protect your networks from harmful outdoor environments and
destructive ESD events with industrial-grade, shielded Ethernet cable from Ubiquiti.
Advertisement
Table of Contents
Related Manuals for Ubiquiti EdgeSwitch 5XP
Summary of Contents for Ubiquiti EdgeSwitch 5XP
- Page 1 For outdoor applications, shielded Category 5 (or above) cabling should be used for all wired Ethernet connections and should be grounded through the AC ground of the power supply. We recommend that you protect your networks from harmful outdoor environments and destructive ESD events with industrial-grade, shielded Ethernet cable from Ubiquiti.
-
Page 2: Hardware Overview
IMPORTANT: Although the cabling can be located outdoors, the EdgeSwitch itself should be housed inside a protective enclosure. WARNING: To reduce the risk of fire or electric shock, do not expose this EdgeSwitch to rain or moisture. Hardware Overview Management Power/Link LED No Power/No Link After bootup, the LED indicates power. -
Page 3: Hardware Installation
RJ45 PoE LED (Ports 1 - 5) No Power over Ethernet Green 24V Power over Ethernet RJ45 Speed/Link/Act LED (Ports 1 - 5) No link Amber Link established at 10/100 Mbps Amber Flashing Link activity at 10/100 Mbps Green Link established at 1000 Mbps Green Flashing Link activity at 1000 Mbps Management Port... -
Page 4: Wall Mounting
WARNING: FAILURE TO PROVIDE PROPER VENTILATION MAY CAUSE FIRE HAZARD. KEEP AT LEAST 20 MM OF CLEARANCE NEXT TO THE VENTILATION HOLES FOR ADEQUATE AIRFLOW. Wall-Mounting... - Page 8 Grounding the EdgeSwitch (Optional)
- Page 9 The EdgeSwitch is grounded through the Power Adapter; however, you can add optional ESD grounding for enhanced ESD protection. Connecting Power...
-
Page 10: Connecting Ethernet
Connecting Ethernet... - Page 11 Note: PoE is disabled by default on all numbered ports and is not available on the Management port. To enable PoE on the appropriate ports, use the Ports tab in the Configuration Interface.
-
Page 12: Accessing The Configuration Interface
Accessing the Configuration Interface Connect to the Configuration Interface: 1. Ensure that your computer (or other host machine) is connected to the Management port on the EdgeSwitch. Note: By default, you can configure the EdgeSwitch via any port; however, we recommend the Management port. -
Page 13: Specifications
The Configuration Interface will appear and allow you to customize your settings. You can enable PoE on the Ports tab. You can also manage your device using the Ubiquiti® Network Management System. UNMS™ lets you configure, monitor, upgrade, and back up your devices using a single application. -
Page 14: Safety Notices
Safety Notices 1. Read, follow, and keep these instructions. 2. Heed all warnings. 3. Only use attachments/accessories specified by the manufacturer. WARNING: Failure to provide proper ventilation may cause fire hazard. Keep at least 20 mm of clearance next to the ventilation holes for adequate airflow. WARNING: To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. -
Page 15: Australia And New Zealand
The limited warranty requires the use of arbitration to resolve disputes on an individual basis, and, where applicable, specify arbitration instead of jury trials or class actions. Compliance Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.