Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ryobi RED1220
Summary of Contents for Ryobi RED1220
- Page 1 ORIGINAL INSTRUCTIONS Electric Edger RED1220...
- Page 2 Important! It is essential that you read the instructions in this manual before assembling, operating and maintaining the product. Subject to technical modification.
-
Page 3: Intended Use
Safety, performance, and dependability have occurring to other people or their property. been given top priority in the design of your ■ Keep bystanders, children, and pets 15 m electric edger. away from the area of operation. Stop the product if anyone enters the area. INTENDED USE ■... - Page 4 are damaged or worn. the blade, blade bolts, and cutter assembly are not worn or damaged. Replace worn ■ If the power cord or extension cable or damaged blade and bolts in sets to becomes damaged during use, disconnect preserve balance. from the power supply immediately.
-
Page 5: Transportation And Storage
the ground. This is particularly important attachment. during starting the product. Never start the product if anyone is in front of the blade. WARNING Inspection after dropping or other impacts: ■ Do not operate the product when there is a Thoroughly inspect the product and identify risk of lightning. -
Page 6: Risk Reduction
contact the authorised service agent. – Wear eye protection at all times. ■ After each use, clean the product with a RISK REDUCTION soft, dry cloth. Any part that is damaged It has been reported that vibrations from should be properly repaired or replaced by handheld tools may contribute to a condition an authorised service centre. -
Page 7: Symbols On The Product
SYMBOLS ON THE PRODUCT Parts or accessories sold separately Read and understand all instructions before operating the product, follow all warnings Note and safety instructions. The following signal words and meanings Wear eye and hearing are intended to explain the levels of risk protection. - Page 8 WHAT’S IN THE BOX...
-
Page 9: Know Your Product
Know your product KNOW YOUR PRODUCT Harness Upper shaft Hanger Adjustment knob Throttle trigger 10. Guide wheel Lock-out trigger 11. Edger blade Rear handle 12. Indication line Cord retainer 13. Blade guard Power cord... -
Page 10: Getting Started
GETTING STARTED Install the lower shaft to the upper shaft.. Always wear safety goggles or safety glasses with side shields when operating the product. Wear non-slip, heavy-duty protective gloves. Wear non-skid, protective footwear that will protect your feet and improve your footing on slippery surfaces. Before using the product, make sure the cable is positioned Form a loop and secure the cable in the cable retainer. - Page 11 GETTING STARTED Install the harness. Install the front handle on the upper shaft. Tighten the adjustment knob securely. Connect the plug to a power outlet. Press the lock-out button (1) and then squeeze the throttle trigger (2).
- Page 12 OVERVIEW Operating the Edger Replacing the blade p.11 p.13 Blade depth adjustment Cleaning the product Storing the product p.14 p.15 p.16...
-
Page 13: Operation
OPERATION OPERATING THE EDGER WARNING: Always operate with two hands and exercise extreme caution when using the product. The blade will reduce in speed if the edger is operated too quickly. 1. Connect the plug to a power outlet. 2. Press the lock-out trigger (1) and then squeeze the throttle trigger (2). - Page 14 OPERATION 3. Operate the edger at a steady pace. The blade begins to freeze when you edge too fast. Do not force the blade into the ground. Avoid edging in wet soil or areas with damp grass and shrubbery. WARNING: The cutting elements will continue to rotate for 2-3 seconds after the product is turned off.
- Page 15 MAINTENANCE REPLACING THE BLADE 1. Disconnect the plug from the power outlet. WARNING: Replace the blade when the blade wears down to the indication line. 2. Insert the locking pin into the inner flange washer. Using the combination wrench, remove the blade nut, outer flange washer and blade.
- Page 16 MAINTENANCE BLADE DEPTH ADJUSTMENT 1. Disconnect the plug from the power outlet. 2. Loosen the adjusting knob. 3. Move the wheel arm up to increase the depth or down to decrease the depth. 4. After adjustment is complete, tighten the adjusting knob securely. NOTE: The blade can be adjusted from 12 mm to 57 mm.
- Page 17 MAINTENANCE CLEANING THE PRODUCT 1. Disconnect the plug from the power outlet. 2. Clean all foreign materials from the product. WARNING: Keep the product away from corrosive agents, such as garden chemicals and de-icing salts.
- Page 18 STORAGE STORING THE PRODUCT NOTE: Make sure to clean the product before storing. 1. Disconnect the plug from the power outlet. 2. Remove the lower shaft from the upper shaft. 3. Store the product.
-
Page 19: Product Specifications
PRODUCT SPECIFICATIONS Electric edger Model RED1220 Rated power 1200 W Rated voltage 230-240 ~ 50 Hz Blade length size 204 mm No-load speed 4000 min Adjustable from 12 Edging depth mm to 57 mm Weight 5.54 kg Recommend torque for blade ≥... - Page 24 Imported by: Techtronic Industries Australia Pty. Ltd. 31 Gilby Road, Mount Waverley, VIC 3149 Melbourne, Australia Techtronic Industries N.Z. Limited 2 Landing Drive, Mangere, RYOBI is a trademark of Ryobi Limited, Auckland, 2022, New Zealand and is used under license. 099119003001-01...