Page 2
An Unpublished Work — All rights reserved. No part of the contents of this docu- mentation or the procedures described therein may be reproduced or transmitted in any form or by any means without prior written permission of Datalogic S.p.A. and/ or its affiliates. Owners of Datalogic products are hereby granted a non-exclusive, revocable license to reproduce and transmit this documentation for the purchaser's own internal business purposes.
Table of Contents Quick Reference ..............1 Features ................1 Installation ................3 Optional Stand/Riser............3 Removing the Stand/Bottom Cover ....4 Magnetic Base Mounting ..........4 How to Scan ................5 Handheld Scanning Mode ..........5 Center Zone Qualification..........6 Scanner Button..............6 Scanner Button Functions ........6 LED and Beeper Indicators ..........8 Programming ..............10 Service Port Mode ..........10 Using Barcodes............10...
This guide is provided to help get your scanner up and running quickly and efficiently. For more details, including additional pro- gramming information, reference the Product Reference Guide (PRG), which is available from the Datalogic website. Features Figure 1. Scanner Features - Front View...
Page 6
Figure 2. Scanner Features - Bottom View Power/interface Cable Latch Release Hole Power/Interface Stand Figure 3. Labeling Regulatory Label (under Serial Number Regulatory bottom cover) Label (under bottom cover) Remove the stand/cover to view the Regulatory Labeling, as described on page 4. Labels are shown to illustrate their location only.
I/F Cable A/C Adapter (if needed) The Magellan 1500i uses intelligent illumination technology to optimize light levels for a variety of bar code scanner functions including automatic reading of bar codes from printed surfaces, mobile devices and image capture in variable contrast environ- ments.
Removing the Stand/Bottom Cover Do not attempt to remove the Stand without first unplugging the Cable as described. Doing so may result in damage to the scanner. CAUTION 1. Unplug the Power Interface Cable by inserting a paper clip or similar object into the latch release hole as shown in Figure 2 on page 2.
How to Scan Bar codes can be presented to the scanner while it is resting on the counter or in the optional stand, or the scanner can be picked up for targeted scanning. Figure 4. Scanning Methods PRESENTATION MODE HANDHELD MODE Scan Button/ Good Read Indicator...
Center Zone Qualification The configurable Center Zone can be set to limit the scan area to allow Targeted Scanning of pick lists or other special items. Bar codes will read in any orientation. The scanner will return to full pattern Presentation Mode when set back down, after a configu- rable time has elapsed.
Page 11
PRESS FUNCTION COMMENT DURATION Press the button for approxi- mately 2 seconds, then Hold, then release. Each time this is release when the Increments tone done, the beeper will sound at beeper sounds one of three tones. Stop when the desired tone (high, medium or low) is sounded.
LED and Beeper Indicators The scanner’s beeper sounds and its green LED illuminates to indicate various functions or errors on the scanner. The tables that follow list these indications. An exception is that the scan- ner’s functions are programmable, and may or may not be turned on.
Page 13
BEEPER INDICATION COMMENT INDICATION The Power-On LED indication is a configurable feature which can be Power On enabled or disabled. When enabled, Single beep Beep this beep indicates the scanner has finished all its power-up tests and is now ready for operation. The good read beep indication is configurable.
Datalogic Scanalyzer or Data- logic Aladdin, all available on the Datalogic website. Service Port Mode To program the Magellan 1500i using Scanalyzer or Aladdin, the unit must first be placed into Service Port mode, as follows: 1. Unplug the unit if needed.
USB-OEM 135(CR) USB Keyboard 000147(CR) USB COM Interface Reference the Product Reference Guide (PRG) or config- uration software (such as Datalogic Aladdin or Scana- lyzer) for additional options. All are available for NOTE download at no charge. Quick Reference Guide...
Good Read Green Spot Duration Successful reading can be signaled by a good read green spot. Use the bar codes that follow to specify the duration of the good read pointer beam after a good read. START / END Disabled Short (300 ms) Medium (500 ms) Long (800 ms)
Cell Mode Frequency Specifies the frequency when reading cell phones. Cell phone mode must be enabled for this feature to be active. Higher Settings will slow down read performance on printed barcodes. NOTE START / END 047100(CR) Cell Mode Frequency = Very Low 047101\r Cell Mode Frequency = Low 047102\r...
Reading of the various bar code symbologies can be independently enabled or disabled in the scanner. If the scanner still does not function properly, consult the Product Refer- ence Guide (PRG) or contact your local supplier or Datalogic Customer Support Services Quick Reference Guide...
Error Codes If an error is detected, the scanner will sound a long low tone (for three seconds) and flash its LED, indicating a failure. When this occurs, press the Scanner button to hear the error code. If it is configured to do so, the scanner will sound a series of beeps cor- responding to the error code and/or flash its LED simultaneous to the beeps.
Cleaning Exterior surfaces and scan windows exposed to spills, smudges or debris accumulation require periodic cleaning to assure best performance during scanning. Use a clean, lint-free cloth or paper towel dampened with a nonabrasive, mild, water-based cleaner to wipe away stains, smudges, fingerprints, spills, etc. from the scan window and exterior surfaces.
Manufacturer Approved Cleaning Materials Datalogic recommends the use of the following cleaners on its products. APPROVED CLEANERS • Hydrogen Peroxide (not to exceed a 3% solution) • Chlorine bleach (not to exceed a 0.25% solution) • Mild detergent and water •...
90 day period starting from the date of shipment of the repaired product from Datalogic or until the expiration of the original Warranty Period, whichever is longer. Datalogic does not...
Page 24
Datalogic shall pay for the return of the product to Buyer if the shipment is to a location within the country in which the Datalogic service center is located. Buyer shall be responsible for paying all shipping charges, duties, taxes, and any other charges for products returned to any other locations.
Page 25
Datalogic or fails to pay when due any invoice under this contract, then in addition to any and all remedies allowed by law, Datalogic without notice may (1) bill and declare due and payable all undelivered products under this or any other contract between Datalogic and the Buyer;...