Eldat RCJ01 Series Manual page 2

GB
RCJ01 Junction Box Receiver
Antenna
Programming Button
L 4A
N N L
L
230 V
N
Models
RCJ01-4102M-01 2-channel 433.92 MHz
RCJ01-5002M-01 2-channel 868.30 MHz
Technical Details
Frequency: 433.92 or 868.30 MHz
Modulation: ASK
Power supply: 230 V AC / 50 Hz
Current consumption: approx. 30 mA
Degree of Protection: IP40
Operating temperature: -20° C to +60° C
Output: 2 relay contacts (N.O.)
potential-loaded
Max. contact rating:
- resistive load cos ϕ=1:
- inductive load cos ϕ=0,8:
Safety Advice
Carefully read through these
instructions before connecting and
operating the unit!
Caution! Electrical installation may only
be carried out by a qualified electrician!
Observe the applicable laws, standards and
regulations as well as the manufacturer's
instructions for the drives to be operated!
Have faulty units checked by the manufactur-
er!
Do not make any unauthorized alterations or
modifications to the unit!
The relay contacts are only suitable for a
single-phase power supply! The contacts
must not be used for switching low voltage
circuits.
Warning! Take care not to damage the
antenna insulation! The antenna could be
live!
Intended Use
This unit may only be used as a radio control
together with shutter drives or blind drives!
The manufacturer shall not be liable for any
damage caused by improper or non-intended
use!
Operating Mode
•
OPEN/CLOSE function
Function
The receiver is designed for switching a shut-
ter drive or blind drive.
with LED
The receiver can be operated by multi-channel
transmitters or single-channel transmitters.
Two-button operation
M
10 codes can be memorized for each of the
OPEN and CLOSE functions.
The running time of the shutter is limited on
3 minutes. After this time the shutter stops
automatically.
Installation Advice
•
When selecting an electric socket, make
sure that the radio transmission between
the transmitter and receiver is unob-
structed. Brick walls and other insulating
materials reduce the range of the radio
transmission.
•
Avoid installing near large metal surfaces
or close to the ground. If installation near
metal surfaces cannot be avoided, main-
tain a distance of at least 10 cm.
Start-Up
1. Take the receiver out of the package.
2. Mount the receiver in accordance with the
4.0 A on-site conditions.
3.2 A
3. Connect the power supply and the
shutter/blind drive motor according to the
wiring diagram. Observe the applicable
electrical regulations.
4. Transfer the codes of the transmitter
buttons to the receiver (see section
"Memorizing the transmitter codes").
Memorizing the Transmission Codes
In the "Memorizing the Transmission Codes"
mode the codes of the transmitter buttons can
be transferred to the receiver.
Note: The same codes can also be pro-
grammed for the OPEN and CLOSE functions
(e.g. when using single-channel transmitters).
1. Briefly press the programming button
(<1.6 s). The programming mode is acti-
vated. The LED flashes.
2. Press and hold the transmitter channel
button, with which you wish to open the
shutter/blind (OPEN function). As soon as
the code is memorized, the LED lights up
for approx. 1 s and then flashes.
3. Press and hold the transmitter channel
button, with which you wish to close the
shutter/blind (CLOSE function). The code
is transferred. As soon as the codes for the
OPEN and CLOSE function are memo-
rized, the LED lights up for approx. 4 s.
For transferring the code of another transmit-
ter, repeat steps 1 to 3.
If all memory locations are occupied, the LED
flashes for approx. 4 s.
Note: By briefly pressing the programming
button, you can abort the programming proce-
dure.
Single-button operation
OPEN
STOP
or
opposite direction
CLOSE
Deleting Specific OPEN/CLOSE Codes
In the "Specific Delete" mode all codes for the
OPEN/CLOSE functions, which are linked to
the pressed transmitter button, can be deleted.
1. Briefly press the programming button
(<1.6 s). The programming mode is
activated. The LED flashes.
2. Keep the programming button pressed for
more than 1.6 s. The delete mode is acti-
vated. The LED flashes rapidly.
3. Press the selected transmitter button.
As soon as the LED of the receiver lights
up for approx. 4 s, the transmission code
has been deleted.
Note: By briefly pressing the programming
button the delete procedure can be aborted.
Reset (Deleting Memory Completely)
In the "Reset" mode all memorized codes can
be deleted.
1. Briefly press the programming button
(<1.6 s). The programming mode is
activated. The LED flashes.
2. Keep the programming button pressed for
more than 1.6 s. The delete mode is acti-
vated. The LED flashes rapidly.
3. Press the programming button again and
keep it pressed for more than 1.6 s.
As soon as the LED lights up for approx.
4 s, all the codes have been deleted.
Note: By briefly pressing the programming
button, the delete procedure can be aborted.
Disposal
Waste electrical products may not be dis-
posed of with household waste!
Dispose of the waste product via a
collection point for electronic scrap or
via your specialist dealer.
Put the packaging material into the
recycling bins for cardboard, paper
and plastics.
Warranty
Within the statutory warranty period we under-
take to rectify free of charge by repair or
replacement any product defects arising from
material or production faults.
Any unauthorized tampering with, or modifica-
tions to, the product shall render this warranty
null and void.
Conformity
This product complies with the essen-
tial requirements of the R&TTE direc-
tive 1999/5/EG.
The Declaration of Conformity can be found on
the internet at: www.eldat.de.
Customer Service
If, despite correct handling, faults or malfunc-
tions occur or if the product was damaged,
please contact the company at the address
below:
ELDAT GmbH
Im Gewerbepark 14
D-15711 Zeesen
Germany
Phone: +49 (0) 33 75 / 90 37-310
Telefax: +49 (0) 33 75 / 90 37-90
Internet: www.eldat.de
e-Mail: info@eldat.de
66691 0505 D/GB