Page 3
IkaScope WS Ultra portable oscilloscope What’s in the box Ordering information and customer support Accessories and maintenance Limited warranty & limitation of liability Document Revisions (c) Ikalogic SAS...
Page 4
IkaScope WS Ultra portable oscilloscope IkaScope WS overview IkaScope WS is an ultra portable oscilloscope probe. It weighs less than g and is designed to fit perfectly in your hand. With a Wifi connection to a smartphone, a tablet or a computer, signals can be displayed and measurements can be easily made.
IkaScope WS Ultra portable oscilloscope Typical applications IkaScope is designed to be mobile, hence applications that require quick, on-the-field measurements are a perfect match for this technology. • Onsite maintenance and inspectio • Isolated measurements • Design troubleshooting • Education and research •...
IkaScope WS Ultra portable oscilloscope Main characteristics Timing Sampling rate (MAX.) MSPS ( bits) Rise time (Calculated) Input channels Sampling memory Kpts Waveform update rate Time base accuracy Vertical Input impedance M || Vertical resolution bits Maximum input voltage Vpp ( CAT I O set range V/Div:...
IkaScope WS Ultra portable oscilloscope V/div V/div General Input protection VAC during minute (production sample test) never exceed Input to USB galvanic isolation VAC minute (production sample test) never exceed Built-in lithium battery Communication interface Wifi . b/g/n/e/i . GHz. Access point or Station Operating, recharging and storage conditions °C to...
IkaScope WS Ultra portable oscilloscope IkaScope WS Interfaces IkaScope WS ports and interfaces are shown in the image below: Figure : IkaScope WS interfaces . Probe tip . Ground lead connection . Status LEDs and charging port . Battery status LED .
IkaScope WS Ultra portable oscilloscope ProbeClick®technology IkaScope incorporates an intelligent probe tip (called ProbeClick®) that detects when pressure is applied. This allows important power saving since all power consuming circuitry is in stand-by when a measurement is not in progress. That same intelligent probe tip is used to turn ON IkaScope, which then turns OFF a er minutes of non activity.
IkaScope WS Ultra portable oscilloscope First connection At this stage, you should configure your display device (Smartphone, tablet or computer) to connect to the Wifi network created by IkaScope. This network’s SSID will start with “IKASCOPE” and will end with the serial number of your IkaScope device.
IkaScope WS Ultra portable oscilloscope Figure : Ikascope application GUI . IkaScope general menu that gives you access to connection options (mainly to connect the application to a specific IkaScope WS device) . Menus for Measurements, cursors, trigger and annotations. .
Page 13
IkaScope WS Ultra portable oscilloscope Figure : Ikascope application screenshot Note: IkaScope device must be turned ON to be connected to a network. If all LEDs are switched OFF, please turn ON IkaScope by pressing on the probe tip for second. Finally, press IkaScope probe tip on the pad where an electric signal needs to be measured.
IkaScope WS Ultra portable oscilloscope So ware technical requirements Download the IkaScope app on www.ikalogic.com so you can use your device on your favorite platform. IkaScope can run on any of those platforms: • A Desktop computer connected to a network that has a Wifi spot (the computer may be connected by ethernet or Wifi).
IkaScope WS Ultra portable oscilloscope Mechanical data Weight: gm ( . ounces) Figure : IkaScope WS dimensions Certifications and regulations EMC : IEC NF/EN - (In high perturbed RF environment, the displayed signal may be altered during perturbation with self recovering) and complies with Limit for class B digital device, pursuant to part of the FCC rules.
Page 16
IkaScope WS Ultra portable oscilloscope • UN . IkaScope contains a Wifi module that complies with the following regulations • CE • FCC (USA) • IC (Canada) • GITEKI • KCC All test certificates can be provided upon request. (c) Ikalogic SAS...
IkaScope WS Ultra portable oscilloscope Safety information This product complies with safety standards IEC NF/EN , IEC NF/EN and UL To prevent possible electrical shock, fire, personal injury, or damage to the product, read all safety information before you use the product. The following international symbols are used on the product and in this manual.
IkaScope WS Ultra portable oscilloscope • Do not use the product if it operates incorrectly. • Before use, inspect device casing, probes, test leads and accessories for mechanical damage and replace if damaged. • Never attempt to repair a defective device. Contact customer service. •...
Page 19
IkaScope WS Ultra portable oscilloscope • Never attempt to replace the battery yourself. Contact customer service in case your battery needs replacement. • Never recharge a device that shows signs of malfunctioning. • Never recharge IkaScope WS for more than hours (disconnect the USB cable from USB port) •...
Page 20
IkaScope WS Ultra portable oscilloscope Accessories and maintenance Accessories and maintenance services are available on our website: www.ikalogic.com or by contacting customer support (support@ikalogic.com). Limited warranty & limitation of liability Each Ikalogic product is warranted to be free from defects in material and workmanship under normal use and service.