1. Manuals
  2. Brands
  3. TECHCON SYSTEMS Manuals
  4. Dispenser
  5. TS1251
  6. User manual

TECHCON SYSTEMS TS1251 User Manual

Ressure dispenser
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
TS1251 PRESSURE DISPENSER
USER'S MANUAL

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TS1251 and is the answer not in the manual?

Questions and answers

Related Manuals for TECHCON SYSTEMS TS1251

Summary of Contents for TECHCON SYSTEMS TS1251

  • Page 1 TS1251 PRESSURE DISPENSER USER'S MANUAL...

  • Page 2: Table Of Contents

    TABLE OF CONTENTS SECTION DESCRIPTION PAGE NUMBER CAUTIONS AND WARNINGS .......... 3 INTRODUCTION ............4 DESCRIPTION ............... 4 & 5 SET UP AND INSTALLATION .......... 6 DESCRIPTION-TS1201 DISPENSING PEN OPTION ..... 8 INSTALLATION-TS1201 DISPENSING PEN OPTION ... 8 & 9 DESCRIPTION-TS1212 MICRO SHOT VALVE OPTION..

  • Page 3: Cautions And Warnings

    1.0 CAUTIONS AND WARNINGS CAUTIONS • 30 PSI (2 BAR) MAX PRESSURE • EYE PROTECTION REQUIRED • DO NOT ATTEMPT TO OPEN LID UNTIL INTERNAL AIR PRESSURE IS RELEASED. • LID KNOB MUST BE HAND TIGHTENED ONLY. WARNINGS READ THE MATERIAL SAFETY DATA SHEETS FOR SPECIAL PRECAUTIONS FOR THE SPECIFIC MATERIAL BEING DISPENSED.

  • Page 4: Introduction

    2.0 INTRODUCTION The TS1251 PRESSURE DISPENSER offers a convenient, easy to use system for dispensing *cyanoacrylates, as well as many solvents, lubricants and other low viscosity materials. Loosen Clamp Knob, swing Lid open, place a container of material to be dispensed, connect Dip Tube, close lid, tighten Clamp Knob, pressurize chamber and begin dispensing.
  • Page 5 10 19 11 12 7 17 18 PARTS LIST No. Part Number Description Qty. No. Part Number Description Qty. TSD601-2 Gasket TSD931-23 Luer Fitting (.07 ID) TSD209-17 Relief Valve 1251-000-011 Dip Tube (.07 ID) TSD1400-243A O-Ring 13 TS1201 Dispense Pen •...

  • Page 6: Set Up And Installation

    Warranty Data. Install pre-assembled Regulator (8) on Rear Base. CAUTION: Plant air supply should provide dried, filtered air with pressure not to exceed 100 psi. If plant air is not dry and filtered, a Techcon Systems 5 Micron Air Filter (TSD800-6) is available as a recommended accessory.
  • Page 7 TS1201 DISPENSING PEN PARTS BREAKDOWN 1201-000-004 PINCH TUBE ASSY. 6-32 X 1/2" LG FLOW ADJUST SCREW TSD1150-7 SPRING 1201-000-003 1212-000-005 PINCH CUSHION PART NUMBER DESCRIPTION QTY. PART NUMBER DESCRIPTION QTY. Page 7...

  • Page 8: Description-Ts1201 Dispensing Pen Option

    4.1 DESCRIPTION- TS1201 DISPENSING PEN OPTION The TS1201 Pen option is a basic Pinch Tube type valve. It has several unique features that provide very broad areas of application. 1. The replaceable Pinch Tube Assy. (3) has inlet and outlet fittings molded onto a Polyethylene Tube. The assembly is capable of shutting off fluid flow with input pressures up to 50 psi of the supply source.

  • Page 9: Description-Ts1212 Micro Shot Valve Option

    When this is necessary, refer to detailed instructions “1201 Pinch Tube Assembly Replacement” (Refer to page 15). 6. The TS1251 Pressure Dispenser with optional TS1201 Dispensing Pen is now ready for use. WARNING: Cyanoacrylate Adhesives are severe eye irritants and skin bonders. Immediate bonding of eyes, skin or mouth may occur upon contact.
  • Page 10 TS1212 MICRO SHOT VALVE .38 DIA 1.19 DIA 2.30 1.58 PARTS LIST 1212-000-005 PINCH CUSHION TSD1399-1 U CUP SEAL 1212-002-000 ADJ. KNOB TSD922-19 HOSE BARB 1212-000-007 GASKET TSD1099-5 TUBING TSD1150-5 SPRING CONNECTOR 1212-000-004 SHUT-OFF PISTON 1212-003-000 PISTON 1212-000-008 ROD MOUNT 1212-004-000 DISPENSE TUBE PART NUMBER...

  • Page 11: Installation-Ts1212 Micro Shot Valve Option

    4.4 INSTALLATION- TS1212 MICRO SHOT VALVE OPTION 1. With Valve mounted as referred to in Section 4.3 Number 4, connect the Luer Lock Fitting at the end of the Dispense Tube onto the inlet side of (7) Pinch Tube on the TS1212 Valve with twisting action (Refer to figure 5). 2.

  • Page 12: Adhesive Supply Replacement

    When this is necessary, refer to detailed instructions “1212 Pinch Tube Assembly Replacement”. (Refer to page 16) The TS1251 Pressure Dispenser with optional TS1212 Dispensing Valve is now ready for use. WARNING: Cyanoacrylate Adhesives are severe eye irritants and skin bonders. Immediate bonding of eyes, skin or mouth may occur upon contact.

  • Page 13: Cleaning Instructions-Dispenser

    6.0 CLEANING INSTRUCTIONS-DISPENSER WARNING: Read the material safety data sheets for special precautions for the specific material being dispensed. Wear protective safety equipment in the material safety data sheets. NOTE: When using solvents, it is essential that precautionary measurers for handling such materials be observed.

  • Page 14: Cleaning/Repair-Ts1201 Dispensing Pen

    e. Activate dispense option (i.e. Press Trigger on Pen, or apply air to Valve), slowly turn Air Press Knob clockwise. Dispense all adhesive into container. Dispense solvent into container for 5 to 10 seconds after adhesive is dispensed. Dispose of properly. 4.
  • Page 15 TS1201 PINCH TUBE ASSEMBLY REPLACEMENT TO REPLACE PINCH TUBE ASSY. 1. Unscrew pivot Pin (a), remove Trigger (b), and Spring (c). 2. Pull one end of Pinch Tube Assy. out (d), stretching it until fitting clears body. 3. Now pull stretched end of Pinch Tube Assy. up (e). Then pull out the opposite end (f) to remove.
  • Page 16 TS1212 PINCH TUBE ASSEMBLY REPLACEMENT 1. Remove Flange Cap, Spring and Shut-Off Piston. 2. Insert male end of pinch tube assembly through side hole of Valve Body. PUSH RODS 3. Tilt the molded male end enough to pass by the Push Rods.
  • Page 17 Part Number Description TSD1400-243A O-Ring TSD1102-19 Tube Clamp TSD125-124 Dispense Tube (.07 ID) TSD931-23 Luer Fitting (.07 ID) 1251-000-011 Dip Tube (.07 ID) TSD126-124 Dispense Tube (.10 ID) TSD931-24 Luer Fitting (.10 ID) 1251-000-020 Dip Tube (.10 ID)

Table of Contents