Advertisement
Quick Links
Advertisement
Related Manuals for Westermo MD-62 AC
Summary of Contents for Westermo MD-62 AC
- Page 1 Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment SERVICE CENTER REPAIRS WE BUY USED EQUIPMENT • FAST SHIPPING AND DELIVERY Experienced engineers and technicians on staff Sell your excess, underutilized, and idle used equipment at our full-service, in-house repair center We also offer credit for buy-backs and trade-ins •...
- Page 2 INSTALLATIONSANVISNING INSTALLATION MANUAL INSTALLATIONS ANLEITUNG 6070-2001 Galvanic Transient Isolation Protection Approved Omvandlare, optisk fiber – RS-232/V.24 Converter, fibre-optic – RS-232/V.24 Glasfaser Wandler – RS-232/V.24 www.westermo.se...
- Page 3 Specifications MD-62 Transmission Asynchronous, full/half duplex or simplex Interface 1 EIA RS-232/CCITT V.24 9-position D-sub connector female or 9-position detachable screw-terminal Interface 2 ST-connectors, see table of power budget Data rate Up to 115.2 kbit/s Indicators Power, TD, RD, RTS, CTS Temperature range 5-50°C ambient temperature Humidity...
-
Page 4: Power Budget
Power budget Min. budget Typ. budget Unit Unit Fibre Fibre 820 nm 1300 nm single mode 820 nm 1300 nm single mode 50/125 10.7 dB 8.1 dB 50/125 16.6 dB 14.6 dB 62.5/125 14.5 dB 11.6 dB 62.5/125 18.6 dB 15.1 dB 100/140 20.6 dB... -
Page 5: Factory Settings
Switch settings MD-62 The MD-62 can, through switch settings, be set in to several modes. To set the switches, open the plastic case by removing the top cover. S1:1-9 S2:1-5 Status signal Transmitted power Enabled 1 2 3 4 5 1 2 3 4 5 6 7 8 9 High Disabled... - Page 6 RD/Received Data RTS/Request To Send CTS/Clear To Send – 1 & 9 SG/Signal Ground I = Input O = Output on MD-62 Power connection Power connection MD-62 AC MD-62 DC (3-position screw-terminal) (2-position screw-terminal) Screw Power Connection Power supply Supply 115*/230V –...
- Page 7 Hints If any problems occur upon set-up of the MD-62, the following notes may be helpful. 1. Power up the MD-62 and check that 3. The RS-232 cable is correct but it still the PWR LED is lit. does not work. The LEDs may be helpful. 2.
- Page 8 MD-62 DCE MD-62 DCE 9 pole (PC) MD-62 DCE 6070-2001...
-
Page 9: Block Diagram
1) Jumper R1 normally not mounted Westermo Teleindustri AB have distributors in several countries, contact us for further information. Westermo Teleindustri AB • S-640 40 Stora Sundby, Sweden Phone +46 16 612 00 Fax +46 16 611 80 E-mail: info@westermo.se • Westermo Web site: www.westermo.se... - Page 10 Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment SERVICE CENTER REPAIRS WE BUY USED EQUIPMENT • FAST SHIPPING AND DELIVERY Experienced engineers and technicians on staff Sell your excess, underutilized, and idle used equipment at our full-service, in-house repair center We also offer credit for buy-backs and trade-ins •...
Need help?
Do you have a question about the MD-62 AC and is the answer not in the manual?
Questions and answers