Windsor Chariot iGloss Burnisher CB20 Operating Instructions Manual page 63

REF PART NO. PRV NO.
1 86004870
2 86254590
3 86005690
4 86253260
5 86270990
6 86234620
7 86259410
8 86071330
9 86248980
10 86231330
11 86008670
12 86012130
13 86071320
14 86276070
15 86270830
16 86066980
17 86255100
18 86090360
19 86078730
20 86316620
21 86316630
22 86273820
23 86005810
24 86277470
25 86091830
26 86254580
27 86316640
28 86248980
29 86300150
30 86001660
31 86274410
32 86010680
33 86249190
34 86253270
35 86272010
*SEE SERIAL NUMBER PAGE
** CALL MANUFACTURER FOR SERIAL NUMBER
QTY
48077 1 KNOB, 3.50 OD X 3/8-16 THRU HOLE
81247 1 SPACER, .500 OD X .391 ID X .300
57085 1 NUT, 3/8-16 HEX JAM
730348 1 SHAFT, PAD ADJ, UPPER
57090 2 NUT, 10-32 HEX NYLOCK SS
270107 1 COUPLER, PAD ADJ
87206 1 WASHER, THRUST .51 ID X 1 OD X .063
140846 1 BRKT, ARM SUPPORT RT
81438 1 PIN, CLEVIS 3/8 X 1.75 PLTD
14664 2 BUSH, BRZ FLG .63 X .75 X 1.0
80606 1 COTTER, 3/8" RING
- 1 ACTUATOR, 36VDC DBLSPD, NOOK
140845 1 BRKT, ARM SUPPORT LFT
70593 2 SCR, 5/16-18 X 3/4 CARRIAGE SS
57023 5 NUT, 5/16-18 HEX NYLOCK SS
149990 3 BAR, COMP. SPRING RETAINER
73443 1 SPRING, DIE COMP. 1.25 OD X 3.0 LG
87492 2 WASHER, SPRING RETAINER
51412 1 PLATE ADJUSTMENT ROD
- 4 NUT, 3/8-16 LG THN HEX SS
- 1 SHAFT, PAD ADJ. LOWER 3/8-16
70019 1 SCR, 1/4-20 X 1.25 HHCS
57245 1 NUT, 1/4-20 HEX NYLOCK SS
70848 1 SCR, 5/16-18 X 1.5 CARRIAGE SS
140847 1 BRKT, ADJUSTMENT ARM
80835 1 SPACER, .32 ID X .71 OD X .79 L NYL
- 1 PIVOT, PAD ADJ L/H THD 3/8-16
81438 1 PIN, CLEVIS 3/8 X 1.75 PLTD
- 1 LINK, ACTUATOR CONTROL ARM
41236 1 HUBCAP, 5/8" SHAFT
70195 2 SCR, 10-32 X 1.25 PPHMS SS
87030 2 WASHER, 3/8 ID X 3/4 OD NYLON
66826 1 PIVOT, PAD ADJUST, L/H THD
730349 1 SHAFT, PAD ADJ, LOWER
57310 4 NUT, 3/8-24 LH THN HEX SS
86306300 CHARIOT BURNISHER 12/13/08
DESCRIPTION
DECK LIFT LINKAGE
SERIAL NO.
NOTES:
FROM
*(1)
*(1)
*(1)
5-26