1. Manuals
  2. Brands
  3. Brillion Manuals
  4. Farm Equipment
  5. Zone Commander ZM3302
  6. Operator's manual

Brillion Zone Commander ZM3302 Operator's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Zone Commander
02 MODELS
Auto Reset --
ZM3302 -4302
ZP3302
ZS3302
Rigid Mount --
ZPR3302 -4302
ZSR3302 -4302
504rev6-16-08
OPERATOR'S MANUAL
:
-5302
-4302
-5302
-4302
-5302
-5302
-5302
www.brillionfarmeq.com
BRILLION
BRILLION, WISCONSIN 54110
B
B
rillion
rillion
-6302
-6362
-6302
-6362
-6302
-6362
-6302
-6362
-6302
-6362
R
-7302
-8302
-7302
-8302
-7302
-8302
-7302
-8302
-7302
-8302
9K162

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Zone Commander ZM3302 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Brillion Zone Commander ZM3302

Summary of Contents for Brillion Zone Commander ZM3302

  • Page 1 -7302 -8302 ZP3302 -4302 -5302 -6302 -6362 -7302 -8302 ZS3302 -4302 -5302 -6302 -6362 -7302 -8302 Rigid Mount -- ZPR3302 -4302 -5302 -6302 -6362 -7302 -8302 ZSR3302 -4302 -5302 -6302 -6362 -7302 -8302 www.brillionfarmeq.com BRILLION BRILLION, WISCONSIN 54110 9K162 504rev6-16-08...

  • Page 3: Table Of Contents

    ontents ontents Introduction ............................3 Location Reference ........................3 Parts Ordering ..........................3 Safety Suggestions ..........................4 Safety Warning Signs ........................5-7 Operating Instructions ........................8 Attaching Tractors With Category II Hitch ..................8 Attaching Tractors With Category III Hitch ................... 8 Level Adjustment ..........................

  • Page 5: Introduction

    SAFETY ALERT ntroduction ntroduction This safety alert symbol is used to call your The Brillion Zone Commander was designed attention to instructions as a primary tillage tool imparting minimum soil concerning personal disturbance and soil eroison while providing ex- safety. This symbol is found throughout this...

  • Page 6: Safety Suggestions

    afety uggestions afety uggestions Federal law requires that you explain the safety and operating instructions furnished with this machine to all employees before they are allowed to oper- ate the machine. These must be repeated to the employees at the beginning of each season.
  • Page 7 • Decals for the Zone Commander, as well have the correct safety decals for the as their locations on the machine, are machine. pictured on the following two pages. • Order replacement decals through your BRILLION dealer. Page 5 9K162...
  • Page 8 Zone Commander Safety Signs: 1. 3J678 - Bleed Air from Cylinders 5. 3K706 - Hydraulic Leak Hazard 2. 9J629 - Watch for Electrical Wires 6. 8J310 - Caution List 3. 3J675 - Falling Wings 7. 9K829 - Deep Till Caution 4.
  • Page 10 peration peration Figure 3a ATTACHING TO TRACTOR Category II Hitch Install 1 1/8” diamter lower hitch pins with pin stop toward inside of machine. Secure with 1/2” capscrew and lock nut. The 1-1/4” O.D. x 1-15/16” Long sleeve may be used on smaller framed machines.

  • Page 11: Level Adjustment

    LEVEL ADJUSTMENT TURNING Adjust the length of the top link so that the The machine should always be raised com- machine is parallel (front to rear) to the ground pletely out of the ground when turning. This surface when operating at the desired depth. will relieve stress on the shanks, mounting hardware, and machine frame.

  • Page 12: Maintenance

    Fasteners Before operating your Brillion tillage implement, check all hardware for tightness. Use the Tightening Torque Chart reproduced below as a guide. After a few hours use, check entire machine and tighten any loose nuts or bolts. Daily or periodic checks should be made thereafter.

  • Page 14: Assembly Instructions

    Assembly ssemblyy ASSEMBLY INSTRUCTIONS Additional parts identification and location can NOTE: 6-shank frame unit is shown in figures. be obtained from reviewing parts catalog. The smaller and larger frame units are similar but reference to figures may not To assemble machine, select a smooth level always be an exact representation.
  • Page 15 Coulter Assemblies If your machine has cast mounting brackets (denoted with number stamped along side of casting) and coulters with round shafts: Attach 6K678 mounting brackets to the front tube with 3/4” 7 x 5 U-bolts. Collars are used to attach front coulter to coulter COLLAR COLLAR REAR OF...
  • Page 16 If your machine is equipped with welded mounting brackets and single or dual coulters on (9K290 square shafts: bracket) mount Attach 9K291 mounting brackets to the front tube with 3/4” x 7 13/16” x 6 3/4” HHCS, 1/2-13 NC x 5” U-bolts and lock nuts.
  • Page 17 DUAL COULTER OPTIONS BASED ON MODEL ZC MODEL 9K320 9K376 9K377 ZS3302 ZS4302 ZS5302 ZS6302 ZS6362 Will require removal of hitch gusset with torch. ZS6382 Will require removal of hitch gusset with torch. ZS6402 Will require removal of hitch gusset with torch. ZS7302 Will require removal of hitch gusset with torch.
  • Page 18 DUAL COULTER PLACEMENT BY MODEL ZS3302 9K320 9K320 9K376 Z4302 9K377 9K376 9K320 9K320 Page 13d 9K162 504rev9-22-05...
  • Page 19 DUAL COULTER PLACEMENT BY MODEL ZS5302 9K320 9K376 9K320 ZS6302 9K377 9K376 504rev7-13-05 Page 13e 9K162...
  • Page 20 DUAL COULTER PLACEMENT BY MODEL ZS6362 ZS6382 9K377 9K376 9K320 9K320 504rev7-13-05 Page 13f 9K162...
  • Page 21 DUAL COULTER PLACEMENT BY MODEL ZS6402 Page 13g 9K162 504rev11-5-07...
  • Page 22 504rev11-5-07 Page 13g-1 9K162...
  • Page 23 1P455 COULTER SET MACHINE CONFIGURATIONS 36" SHANK SPACING U-BOLTS IN OUTER TOP VIEW SET OF HOLES 13 3/4" 15 5/8" for 36" Spacing 7 1/8" 29" REF for 36" Spacing 7" REF TYP BOTTOM VIEW 38" AND 40" SHANK SPACING U-BOLTS IN INNER TOP VIEW SET OF HOLES...
  • Page 24 ZS7302 9K377 9K320 9K320 Page 13h 504rev11-5-07 9K162...
  • Page 26 4. Shank Assemblies 4a. Shear-Bolt (or Rigid) Shank REAR LOCK NUT, CAPSCREW, 1-8NC 1-8NC x 8” LOCK NUT, BUSHING 1-8NC #8K364 LOCK NUT, HHCS, 3/4-10 NC 1-8 NC x 4 1/2” PLUG ASSEMBLY #8K367 (2) - HHCS, 5/16-18 X 1” Lock Washer, 5/16”...
  • Page 27 - Assemble shear bolt shank mount with front shank clamp to rear tube of machine directly behind each coulter assembly. - Attach as shown in figure 8a using (4) 1-8 NC x 8” gr. 5 capscrews and locknuts. • Torque shank mounting clamp bolts to 200 ft.
  • Page 28 REAR OF MACHINE WEARSTRIP BRACKET Bracket fits over wide part of wearstrip - Fasten tight LOCK NUT, against shank. 1-8NC CAPSCREW, 3/4-10NC x 3” Reversible Wearstrip (Straight Shank only) PARABOLIC SHANK V-CAST STEEL POINT CAPSCREW, V--WEARSTRIP 1/2-13 NC x 2 1/2” (Parablolic Shank ) w/ STOVER NUT 1/2-13 NC...
  • Page 29 CAPSCREW, 1-8NC x 8” REAR OF Figure 11 MACHINE FRONT CLAMP NUT, 1-8 NC STRAIGHT SHANK Auto-Reset Shank - Assemble Auto-Reset shank assembly to Figure 12 rear tube of machine directly behind coulter assemblies. Attach with 6K790 front shank clamp as shown in using four 1-8 NC x 8” Gr.
  • Page 30 TO REPLACE SHANK MOUNT & LEG: WARNING! AUTO-RESET SHANK IS ALWAYS UNDER LOAD Spring is loaded and improper removal of bolts could result in serious injury. Shank is spring loaded and serious injury could result as shank resets. Do not disassemble without following procedure outlined in operator’s manual. Do not use hands or feet to dislodge any obstruction holding the shank in the tripped position.
  • Page 31 SHEAR BOLT REPLACEMENT: Excessive distortion of holes in the shear bolt bushings and/or shank ,as well as improper bolt grade and length, can result in premature or improper bolt shearing in both types of shanks. 1. Examine the replaceable bushings in REAR the side plates for excessive distortion.
  • Page 32 CAPSCREW, 5/8-11 NC x 9 1/2” LOCKWASHER, 5/8” NUT, 5/8-11 NC MOUNTING PLATE REAR OF MACHINE Page 20 504rev8-4-06...
  • Page 33 #7K851 Gage Wheel Kit See Repair parts catalog for complete listing of parts. Gage Wheel Assembly, #7K709 Gage Wheel Assembly, #7K710 HHCS, 1-8 NC x 7 1/2” LOCK NUT, 1-8 NC PIVOT BOLT SLOTTED NUT & HHCS, COTTER PIN 1-8 NC x 4 1/2” TOP LINK GAGE WHEEL ARM HUB &...

  • Page 34: Warning Lamp Assembly

    WARNING LAMP ASSEMBLY Assemble the light bar to the angles on their supports with 3/8-16 U-bolts, and the supports to the rear tube of the frame with 5/8-11NC U-bolts and lock nuts. The side of the light bar with the red decals goes toward the rear, and the side with amber only toward the front of the machine.
  • Page 35 The plug on the other end of the straight harness Attach permanently to implement frame. connects to the tractor socket when in use. When not in use, it can be stored at the connector holder All wires must be firmly attached to machine on the hose support bracket.

  • Page 36: Model Configuration

    Typical Zone Commander Configuration Figure 22 ZS6302 The ZONE COMMANDER is designed to ac- commodate many configurations, (See figures on the following pages). Use these diagrams as a guide also if the ones pictured do not exactly match your model specifications. MODEL CONFIGURATION Note: Wheels may be installedeither direction...
  • Page 37 Figure 23b 4302 MODELS 5302 MODELS Figure 23c Page 25 9K162...
  • Page 38 Figure 23d 6302 MODELS 9K320 9K376 9K320 6362 MODELS Figure 23e Page 26 9K162 504rev9-28-04...
  • Page 39 Figure 23f 6382 MODELS 6402 MODELS Figure 23g Page 27 9K162...
  • Page 40 7302 MODELS Figure 23h 8302 MODELS Figure 23i Page 28 9K162...
  • Page 41 This Page Left Blank Intentionally Page 29 9K162...

  • Page 42: Row Marker

    Row Markers Row markers are mounted with mounting channels, as shown, with longer ones supported by arm cradles. 1. Place the mounting channels into position Figure 24a and hold with 3/4” x 5 13/16” x 10 1/2” U-bolts and lock nuts. Position them as far apart as possible in accordance with row shank spacing.
  • Page 43 Figure 25 Male Tractor Adapter, Connector .06 Male JIC x Male O-Ring To Tractor Rear of Machine Page 31 9K162 504rev8-30-05...
  • Page 44 Page 32 9K162 504rev8-17-06...
  • Page 45 Page 33 9K162 504ev8-17-06...

  • Page 46: Support Arm Kits

    TTACHMENTS TTACHMENTS Support Arm Kit Assemble support stand as shown depending upon your shank type: *Apply Loc-Tite to threads and tighten to 400 foot-pounds * Replace the existing bolts with these longer bolts, 7K872 Auto-reset Shank Models attaching angles to side plates. Heads and washers must be on this side as shown.
  • Page 47 with: 7K873 Ripple (Wavy) Coulter Kit 7K928 Disc Kit Support Arm Coulter Mount Assemble to support arm as shown: U-bolt, 1/2-13 NC x 5 1/2” x 4 1/2” Lock Nuts Set Screw, 1/2-13 NC 1/2-13 NC x 4” Roll Pin, 1/4”...
  • Page 48 and/or Ductile Notched End Wheel Frame HHCS, 5/16-18 NC x 1” Axle Clamp Assembly Pipe Weldment Lock Washer, 5/16” Hex Nut, 5/16-18 NC Flangette half Bearing & Axle Clamp Basket Collar Assembly Crumbler End Wheel 7K874 Basket Kit - Page 36 9K162...
  • Page 49 7K925 Ductile Wheel Kit 7K924 Optimizer Wheel Kit Page 37 9K162...
  • Page 50 [Frame for ref.] Outer Arm Center Arm U-bolt, 5/8-11 NC x 5 11/16” x 13” Lock Nut, 5/8-11 NC Outer Arm U-bolt, 5/8-11 NC x 4-11/16” x 5-5/8” Two Bar Welded Lock Nut, 5/8-11 NC Hitch Rear Rigid Hitch Kit -(Pull-type) - 9K071 Assemble to Zone Commander frame as shown with hardware provided.

  • Page 51: Model Designation

    achine pecifications achine pecifications (Subject to change without notice) Model Designation Basic model is denoted by : - Zone Commander, Straight Shank (Spring-reset, Minimum Disturbance Shank Mount) - Zone Commander, Straight Shank, Spring-reset Shank Mount - Zone Commander, Single Bar Frame, Parabolic Shank (Spring-reset Shank Mount) - Zone Commander, Straight Shank, Rigid Shank Mount - Zone Commander, Parabolic Shank, Rigid Shank Mount The number following relates to the intended shank combination of the machine.
  • Page 54 Equipment from Landoll Corporation is built to exacting standards ensured by ISO 9001:2008 registration at all Landoll manufacturing facilities. LANDOLL CORPORATION 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM Copyright 2010. Landoll Corporation "All rights reserved, including the right to reproduce this material or portions thereof in any form"...

This manual is also suitable for:

Zone commander zm4302Zone commander zm5302Zone commander zm6302Zone commander zm6362Zone commander zm7302Zone commander zm8302 ... Show all

Table of Contents