Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Brillion Compaction Commander 03 Series
Summary of Contents for Brillion Compaction Commander 03 Series
- Page 1 OPERATOR’S MANUAL rillion rillion ompaction ommander -03 MODELS Single Bar Frames CCS3303 -5303 Double Bar Frames CCD3303 -4303 -5243 -5303 -6243 -6303 -7303 -8303 -9243 www.brillionfarmeq.com BRILLION BRILLION, WISCONSIN 54110 9K308 604rev10-4-05...
- Page 2 Page 1 9K308...
-
Page 3: Table Of Contents
ontents ontents Introduction ............................3 Location Reference ........................3 Parts Ordering ..........................3 Safety Suggestions ..........................4 Safety Warning Signs ........................5-7 Operating Instructions ........................8 Attaching Tractors With Category II Hitch ..................8 Attaching Tractors With Category III Hitch ................... 8 Level Adjustment .......................... -
Page 5: Introduction
If items covered in this manual are not under- stood, contact your local Brillion dealer. Figure 1 Location Reference Right hand, left hand and forward designations are those related to the operator when sitting in the operating position. -
Page 6: Safety Suggestions
afety uggestions afety uggestions Federal law requires that you explain the safety and operating instructions furnished with this machine to all employees before they are allowed to oper- ate the machine. These must be repeated to the employees at the beginning of each season. - Page 7 • Decals for the Zone Commander, as well have the correct safety decals for the as their locations on the machine, are machine. pictured on the following two pages. • Order replacement decals through your BRILLION dealer. Page 5 9K308...
-
Page 8: Safety Warning Signs
4. 2J431 - Amber Reflective Safety Signs: 5. 2J430 - Red Reflective 6. 8K597 - Red-Orange Reflective 7. 4K103 - Brillion 8. 4K067 - Compaction Commander CAUTION 1. DO NOT LUBRICATE, ADJUST OR REPAIR WHEN MACHINE IS IN MOTION. 2. DO NOT TOW OR TRANSPORT FASTER THAN 15 MILES PER HOUR. -
Page 10: Operating Instructions
peration peration Figure 3a ATTACHING TO TRACTOR PIN ASSEMBLY, 1” DIA. HHCS, SLEEVE, 3/8-16 NC X 2 1/2” Category II Hitch 1-1/32 I.D. x 1-7/16” O.D. LOCK NUT, x 2-7/8” LONG 3/8-16 NC Install 1 1/8” diamter lower hitch pins with pin stop toward inside of machine. -
Page 11: Level Adjustment
LEVEL ADJUSTMENT TURNING Adjust the length of the top link so that the The machine should always be raised com- machine is parallel (front to rear) to the ground pletely out of the ground when turning. This surface when operating at the desired depth. will relieve stress on the shanks, mounting hardware, and machine frame. -
Page 12: Maintenance
Fasteners Before operating your Brillion Zone After a few hours use, check entire machine Commander, check all hardware and tighten any loose nuts or bolts. Daily or tightness. Use the Tightening Torque periodic checks should be made thereafter. -
Page 13: Tires
Page 11 9K308... -
Page 14: Assembly Instructions
Assembly ssemblyy ASSEMBLY INSTRUCTIONS Additional parts identification and location can NOTE: 6-shank frame unit is shown in figures. be obtained from reviewing parts catalog. The smaller and larger frame units are similar but reference to figures may not To assemble machine, select a smooth level always be an exact representation. -
Page 15: Couter Assembly
SET SCREW, U-BOLT, 3/4” COLLAR REAR OF 5/8-11 x 2” (SQ. HD) (2) SET SCREWS, MACHINE 5/8-11 x 2” (SQ. HD) (2) NUTS, 5/8-11 NC MOUNTING NUT, 5/8-11 NC BRACKET COLLAR LOCK WASHER, 3/4” NUT, 3/4-10 NC Figure 7 Offset Bracket (used in models where normal placement interferes with mast). -
Page 16: Shank Assembly
4. Shank Assemblies CARRIAGE BOLT, 3/4 X4” 3/4-10 NC Lock Nut, 5/8” lOCK WASHERS HEX NUTS, 5/8-11 NC Lock Nut, 7/8-9 NC HHCS, 7/8-9 NC x 4 1/2” HHCS, 5/8-11 NC x 4” (2) 5/8” FLAT WASHERS CAPSCREW, 5/8 NC x 3 1/4” HHCS, 1/2”... - Page 17 FRONT CLAMP - Assemble shank mount with front shank clamp to rear tube of machine directly behind each coulter assembly. - Attach as shown using (2) 7/8-9 NC x 4 1/2” capscrews and locknuts over the top of the frame and (2) 7/8-9 NC x 7 1/2” ” gr. 5 capscrews and locknuts underneath.
-
Page 18: Shank Mount Replacement
Service of Preloaded Shank Assembly SPRING IS UNDER LOAD Do not disassemble without use of service tool and following the procedure. Spring is loaded and improper removal of bolts could result in serious injury. Refer to Repair Parts Catalog for additional help in identifying parts of shank assembly and service kit. -
Page 19: Gage Wheels
MOUNTING PLATE CAPSCREW, 5/8-11 NC x 4” CAPSCREW, 5/8-11 NC x 9 1/2” LOCKWASHER, 5/8” NUT, 5/8-11 NC REAR OF Figure 10 MACHINE Page 17... -
Page 20: Warning Lamp Assembly
WARNING LAMP ASSEMBLY Assemble the light bar to the angles on their Red Lamp supports with 3/8-16 U-bolts, and the supports to the rear tube of the frame with 5/8-11NC U-bolts and lock nuts. The side of the light bar with the red decals goes toward the rear, and the side with amber only toward the front of the machine. - Page 21 The plug on the other end of the straight harness Attach permanently to implement frame. connects to the tractor socket when in use. When not in use, it can be stored at the connector holder All wires must be firmly attached to machine which mounts to the rear plate of the mast.
-
Page 22: Model Configuration
Compaction Commander Configuration Figure 15 CCD6303 The COMPACTION COMMANDER is designed to accommodate various configurations, (See figures on the following pages). Use these diagrams as a guide also if the ones pictured do not exactly match your model specifications. Page 2 9K308... - Page 23 MODEL CONFIGURATION - CCS Note: Wheels may be installedeither direction CCS 3303 30” Spacing Figure 16a CCS 5303 30” Spacing Figure 16b Page 21 9K308...
- Page 24 MODEL CONFIGURATION-CCD Figure 16c CCD3303 CCD4303 Figure 16d Page 22 9K308...
- Page 25 Figure 16e CCD5243 CCD5303 Figure 16f Page 23 9K308...
- Page 26 Figure 16g CCD6243 MODELS CCD6303 MODELS Figure 16h Page 24 9K308...
- Page 27 Figure 16i 7303 MODELS 8302 MODELS Figure 16i Page 25 9K308...
- Page 28 CCD9243 Figure 16j Page 26 9K308...
- Page 29 This Page Left Blank Intentionally Page 27 9K308 604rev10-4-05...
-
Page 30: Row Marker Option
Row Markers Row markers are mounted with mounting channels, as shown, with longer ones supported by arm cradles. 1. Place the mounting channels into position Figure 17a and hold with 3/4” x 5 13/16” x 10 1/2” U-bolts and lock nuts. Position them as far apart as possible in accordance with row shank spacing. - Page 31 Male Tractor Adapter, Connector .06 Male JIC x Male O-Ring Figure 18 To Tractor Rear of Machine Page 29 9K308 604rev10-4-05...
-
Page 32: Specifications
achine pecifications achine pecifications (Subject to change without notice) Model Designation Basic model is denoted by : - Compaction Commander, Single-Bar Frame - Compaction Commander, Double-Bar Frame The number following relates to the intended shank combination of the machine. example = 5303 - 5 shanks on 30” spacing, - model series 3 Basic Machine Specifications Overall Width -follows numeric part of model designation: CCS3303, CCD3303... - Page 34 Equipment from Landoll Corporation is built to exacting standards ensured by ISO 9001:2008 registration at all Landoll manufacturing facilities. LANDOLL CORPORATION 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM Copyright 2010. Landoll Corporation "All rights reserved, including the right to reproduce this material or portions thereof in any form"...
Need help?
Do you have a question about the Compaction Commander 03 Series and is the answer not in the manual?
Questions and answers