Technical Data - Graco Dispensit 1092 Operation & Maintenance Manual

Technical Data

NOTE: See feed system manuals for dimensions, weights, and wetted parts lists for those components. Dimensions,
weights, and wetted parts for components not covered in component feed system manuals and for combined assem-
blies are listed below.
Maximum Ambient Temperature. . . . . . . . . . . . . . . . . . . . 110°F (43°C)
Maximum Operating Temp . . . . . . . . . . . . . . . . . . . . . . . . 150°F (65°C)
Maximum Outlet Fluid Working Pressure . . . . . . . . . . . . . 2000 psi (14 MPa, 138 bar)
Maximum Air Working Pressure . . . . . . . . . . . . . . . . . . . . 100 psi (0.7 MPa, 7 bar)
Minimum Air Working Pressure . . . . . . . . . . . . . . . . . . . . 70 psi (480 kPa, 4.8 bar)
Maximum Material Inlet Pressure . . . . . . . . . . . . . . . . . . . Metal Sleeves: 1200 psi (8 MPa, 83 bar)
Supplied Air Requirements. . . . . . . . . . . . . . . . . . . . . . . . 1 to 3 cfm at 80 psi to 100 psi
Shot Size Range (depending on metering rods selected) 0.024 cc to 9.600 cc
Maximum Cycle Rate (application dependent, heat
required) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Up to 60 cycles per minute
Dimensions:
Height (to end of material inlet block):
1092-10A-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1092-10A-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1092-10A-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Length:
Non Cycle Detection . . . . . . . . . . . . . . . . . . . . . . . . .
Cycle Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Width:
Single Needle Outlet (Standard) . . . . . . . . . . . . . . . .
Weight
1092-10A-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1092-10A-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1092-10A-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wetted Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Metering Valve: Hardened steel, 303/304, 404, UHM-
332089C
Plastic Sleeves: 400 psi (2.8 MPa, 28 bar)
12.53 in. (395 mm)
17.16 in. (436 mm)
20.28 in. (515 mm)
8.38 in. (213 mm)
9.13 in. (232 mm)
1.75 in. (45 mm)
Graco-supplied Feed System Assemblies
(depends on selected options):
Smallest: 22.5 x 10 x 4 in. (572 x 254 x 102 mm)
Largest: 60 x 28 x 19 in. (1524 x 711 x 483 mm)
6-7 lb (2.72-3.18 kg)
10-11 lb (4.54-4.99 kg)
14-15 lb (6.35-6.80 kg)
WPE, Tungsten, carbide, fluoroelastomer, EPDM,
PTFE, Acetal
Graco-supplied Feed System Hoses and Fittings: Mild
steel, 303/304, PTFE, buna, polyethylene, polypropyl-
ene
Graco-supplied Tanks: Polyethylene, 303/304, mild steel
Technical Data
37