Table of Contents
Advertisement
Refer to equipment manufacturers' instructions for specific
system wiring information.
You can configure the thermostat for use with either multi-stage
electric heat systems or multi-stage gas systems. When con-
figured for electric
electric heat, the G G G G G terminal (blower/fan) will be
electric
electric
electric
energized on a call for heat.
This thermostat is designed to operate a single-transformer
system. If you have a two-transformer system, cut and tape off
SYSTEM
SYSTEM
SYSTEM
SYSTEM
SYSTEM
L L L L L
Multi-stage Malfunction
24 Volt
Light
(Common)
*The 24 volt neutral connection to terminal C on the thermostat is not required if you replace the batteries once a year with fresh "AA" Energizer
CHECK THERMOSTAT OPERATION
CHECK THERMOSTAT OPERATION
CHECK THERMOSTAT OPERATION
CHECK THERMOSTAT OPERATION
CHECK THERMOSTAT OPERATION
NOTE
To prevent static discharge problems, touch side of
To prevent static discharge problems, touch side of
To prevent static discharge problems, touch side of
To prevent static discharge problems, touch side of
To prevent static discharge problems, touch side of
thermostat to release static build-up before touching
thermostat to release static build-up before touching
thermostat to release static build-up before touching
thermostat to release static build-up before touching
thermostat to release static build-up before touching
any keys.
any keys.
any keys.
any keys.
any keys.
If at any time during testing your system does not operate
properly, contact a qualified serviceperson.
Fan Operation
Fan Operation
Fan Operation
Fan Operation
Fan Operation
If your system does not have a G G G G G terminal connection, skip to
Heating System
Heating System
Heating System
Heating System
Heating System.
1. Turn on power to system.
2. Move FAN switch to ON
ON
ON position. The blower should begin
ON
ON
to operate.
3. Move FAN switch to AUTO
AUTO position. The blower should
AUTO
AUTO
AUTO
stop immediately.
CAUTION
!
Do not allow the compressor to run unless the com-
Do not allow the compressor to run unless the com-
Do not allow the compressor to run unless the com-
Do not allow the compressor to run unless the com-
Do not allow the compressor to run unless the com-
pressor oil heaters have been operational for 6 hours
pressor oil heaters have been operational for 6 hours
pressor oil heaters have been operational for 6 hours
pressor oil heaters have been operational for 6 hours
pressor oil heaters have been operational for 6 hours
and the system has not been operational for at least
and the system has not been operational for at least
and the system has not been operational for at least
and the system has not been operational for at least
and the system has not been operational for at least
5 minutes.
5 minutes.
5 minutes.
5 minutes.
5 minutes.
Heating System
Heating System
Heating System
Heating System
Heating System
1. Press SYSTEM button to select the Flame icon
the auxiliary heating system has a standing pilot, be sure
to light it.
2. Press
to adjust thermostat setting to 1° above room
temperature. The heating system should begin to
operate. The display should show "STG1"
setpoint temperature display is flashing, the compressor
lockout feature is operating (see Configuration menu,
item 5).
3. Adjust temperature setting to 3° above room temperature.
If your system configuration is set at MS2, HP2 or HP1,
the auxiliary heat system should begin to operate and the
display should show "STG1+2"
"STG1+2".
"STG1+2"
"STG1+2"
"STG1+2"
4. Press
to adjust the thermostat below room tempera-
ture. The heating system should stop operating.
4
Multi-Stage Terminal Outputs
Multi-Stage Terminal Outputs
Multi-Stage Terminal Outputs
Multi-Stage Terminal Outputs
Multi-Stage Terminal Outputs
THERMOSTAT TERMINALS (MULTI-STAGE)
THERMOSTAT TERMINALS (MULTI-STAGE)
THERMOSTAT TERMINALS (MULTI-STAGE)
THERMOSTAT TERMINALS (MULTI-STAGE)
THERMOSTAT TERMINALS (MULTI-STAGE)
C*
C*
C*
C*
C*
R R R R R
W2
W2
W2
W2
W2
24 Volt Heat Mode Heat mode Cool Mode Cool Mode Blower/Fan Energized Energized Energized
(Hot)
2nd stage
1st stage
Flame icon ( ). If
Flame icon
Flame icon
Flame icon
"STG1"
"STG1"
"STG1". However, if the
"STG1"
one transformer. If transformer safety circuits are in only one of
the systems, remove the transformer of the system with NO
safety circuits. If required, replace remaining transformer with
a 75VA Class II transformer. After disconnecting one trans-
former, the two commons must be jumpered together.
Use the terminal output information below to help you wire the
thermostat properly for your multi-stage system. After wiring,
see CONFIGURATION
CONFIGURATION
CONFIGURATION section for proper thermostat configu-
CONFIGURATION
CONFIGURATION
ration.
E/W1
E/W1
E/W1
E/W1
E/W1
Y2
Y2
Y2
Y2
Y2
Y1
Y1
Y1
Y1
Y1
2nd stage
1st stage
EMER bypasses the Heat Pump to use the heat source wired
to terminal E on the thermostat. EMER is typically used when
compressor operation is not desired, or you prefer back-up
heat only.
1. Press SYSTEM button to select EMER. "EMER"
on the display.
2. Press
to adjust thermostat setting above room
temperature. The Aux. heating system will begin to
operate. The display will show "STG1"
Flame icon
Flame icon
and Flame icon
Flame icon
Flame icon ( ) to indicate that the Aux. system is
operating.
3. Adjust temperature setting to 3° above room temperature.
The auxiliary heat system should begin to operate and the
display should show "STG1+2"
4. Press
to adjust the thermostat below room tempera-
ture. The Aux. heating system should stop operating.
To prevent compressor and/or property damage, if
To prevent compressor and/or property damage, if
To prevent compressor and/or property damage, if
To prevent compressor and/or property damage, if
To prevent compressor and/or property damage, if
the outdoor temperature is below 50°F, DO NOT
the outdoor temperature is below 50°F, DO NOT
the outdoor temperature is below 50°F, DO NOT
the outdoor temperature is below 50°F, DO NOT
the outdoor temperature is below 50°F, DO NOT
operate the cooling system.
operate the cooling system.
operate the cooling system.
operate the cooling system.
operate the cooling system.
1. Press SYSTEM button to select the Snowflake icon
2. Press
to adjust thermostat setting below room
temperature. The blower should come on immediately on
high speed, followed by cold air circulation. The display
should show "STG1"
3. Adjust temperature setting to 3° below room temperature.
The second stage cooling should begin to operate and
the display should show "STG1+2"
4. Press
to adjust the temperature setting above room
temperature. The cooling system should stop operating.
G G G G G
on call for Cool (and
in Cool
Heat if configured
to Electric Heat)
Emergency System
Emergency System
Emergency System
Emergency System
Emergency System
"STG1"
"STG1"
"STG1"
"STG1" flashing "EMER"
"STG1+2"
"STG1+2"
"STG1+2".
"STG1+2"
CAUTION
!
Cooling System
Cooling System
Cooling System
Cooling System
Cooling System
Snowflake icon
Snowflake icon ( ).
Snowflake icon
Snowflake icon
"STG1".
"STG1"
"STG1"
"STG1"
"STG1+2".
"STG1+2"
"STG1+2"
"STG1+2"
O O O O O
B B B B B
in Heat, Off,
Mode
Emergency
Modes
®
alkaline batteries.
"EMER" will flash
"EMER"
"EMER"
"EMER"
"EMER"
"EMER"
"EMER"
"EMER"
Hide quick links:
Advertisement
Table of Contents
