Nordson ColorMax Manual
Color change procedures powder booth with powder port feed center and prodigy hdlv powder transfer system
Hide thumbs
Also See for ColorMax:
- Customer product manual (88 pages) ,
- Manual (22 pages) ,
- Operator card (8 pages)
Related Manuals for Nordson ColorMax
Summary of Contents for Nordson ColorMax
- Page 1 Color Change Procedures ColorMax Powder Booth with Powder Port Feed Center ® and Prodigy ® HDLV ® Powder Transfer System 1093876A...
- Page 2 WARNING: Allow only qualified personnel to WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in your powder coating equipment manuals. © 2008 Nordson Corporation All Rights Reserved...
- Page 3 Move the booth offline if it is a Move the booth offline if it is a Turn all automatic spray guns off. Roll On/Roll Off booth. Wait until the Gun Blow Off/Purge Cycle is complete. Go to page 10. © 2008 Nordson Corporation All Rights Reserved...
- Page 4 Remove the powder lance from the hopper and insert it into the purge chute. Rotate the hold-down latch over the lance to secure it in the chute. © 2008 Nordson Corporation All Rights Reserved...
- Page 5 Reclamp the sieve and restart the Reclaim t t th R transfer pump. © 2008 Nordson Corporation All Rights Reserved...
- Page 6 Install a lid on the hopper. Blow down the lance, purge chute and hold-down latch chute and hold down latch, lance guide, walls, and floor. © 2008 Nordson Corporation All Rights Reserved...
- Page 7 Remove the screen gasket and clean it thoroughly. Blow off the feed center walls and floor. Re-assemble the sieve. Turn on the Reclaim transfer pump. transfer pump. Leave the transfer hoses connected to the purge ports. © 2008 Nordson Corporation All Rights Reserved...
- Page 8 CLEANING THE BOOTH AND EXITS: Purge the Virgin Transfer Pump at the Bulk Feed Unloader Bulk Feed Unloader. Press the Reclaim Transfer Purge Start Transfer Purge Start button to purge the reclaim pump. © 2008 Nordson Corporation All Rights Reserved...
- Page 9 Install the level sensor on the feed hopper. Remove the lance from the purge chute and the purge chute and install it through the lance guide and into the powder. © 2008 Nordson Corporation All Rights Reserved...
- Page 10 Blow off doors at entry end of the Swing open the Aerodecks after For Hard-to-Clean Powders: booth. blowing them off. Wipe down the booth interior, inlet duct, and vertical duct with damp cotton towels. © 2008 Nordson Corporation All Rights Reserved...
- Page 11 For Hard-to-Clean Powders: Wipe down the interior of the transfer pan with damp For Hard-to-Clean Powders: cotton towels. Wipe down the interior of the cyclone with damp cotton towels. © 2008 Nordson Corporation All Rights Reserved...
- Page 12 Clean the pickup tube. Vacuum the floor and drum cart. Install the new color drum on the cart on the cart. Install the pickup tube in the new drum. © 2008 Nordson Corporation All Rights Reserved...
- Page 13 Clean off any powder residue. Inspect the gun positions and blow-off nozzles. Make sure the gun nozzles are clean and there is no impact clean and there is no impact fusion present on the nozzles. © 2008 Nordson Corporation All Rights Reserved...
-
Page 14: System Start-Up
Make sure the spray room is clean and all powder has Start the System, Afterfilter, and Powder Port been cleaned off the floor and Feed Center at the main electrical panel. exterior of the booth and equipment. © 2008 Nordson Corporation All Rights Reserved... - Page 15 Cyclone Components MANUAL PURGE button Transfer pan latch Reclaim pump supply air regulator/gauge Cyclone access doors Transfer pan fluidizing air regulator/gauge Transfer pan © 2008 Nordson Corporation All Rights Reserved...
- Page 16 Feed Center Components Control Panel Fluidizing Regulator Feed Pumps Feed Pumps Feed Hopper Powder Lance Sieve Sieve Nordson Corporation 300 Nordson Drive Amherst, Ohio 44001 © 2008 Nordson Corporation P/N 1093876A All Rights Reserved Released 12/08...