Advertisement
Quick Links
43160B - 43166B Rhino Pioneer Front / Side Rail Kit
Place these instructions in the vehicle's glove box after installation is complete.
Important:
Please read these instructions carefully prior to installation.
Please refer to your fitting instruction to ensure that the alloy tray is installed correctly.
Check the contents of this kit before commencing fitment and report any discrepancies.
Rail shown suits tray 42104B
Item
Component Name
1
End Rail Extrusion
2
Side Rail Extrusion
3
Corner Moulding
4
Corner Moulding Cover
5
End Moulding LH
6
End Moulding LH Cover
7
End Moulding RH
8
End Moulding RH Cover
9
Rail Support End
10
Rail Support Side
11
Phillips Screw
12
M8 x 20mm Hex Bolt
13
M8 Spring Washer
14
M8 x 30mm Flat Washer
15
M8 Channel Nut
16
Fitting Instructions
Suits Trays
Rail Lengths (mm)
Rhino-Rack
3 Pike Street, Rydalmere,
NSW 2116, Australia.
(Ph) (02) 9638 4744
(Fax) (02) 9638 4822
These instructions remain the property of Rhinorack Australia Pty Ltd and may not be used or changed for any other purpose than intended.
Part No.
43160B
43161B
-
1
-
2
M511
2
M512
2
M515
1
M516
1
M517
1
M518
1
M513
3
M514
4
B176
12
12
B020
9
11
W019
9
11
C949
9
11
N003
9
11
R034
1
42104B
42105B
42108B
42111B
42112B
42113B
1152 &
1191 &
400
750
Document No: R034
Prepared By: Nigel Greig
Authorised By: Chris Murty
Quantity
43162B
43163B
1
1
1
2
2
2
2
2
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
3
2
2
6
2
4
12
12
6
8
6
8
6
8
6
8
1
1
1
42106B
42100B
42102B
42107B
42109B
446 &
962 &
150
400
CONTROLLED
43164B
43165B
43166B
1
1
1
2
2
2
2
2
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
3
2
2
4
4
4
12
12
12
9
8
8
9
8
8
9
8
8
9
8
8
1
1
1
42101B
42114B
42115B
42103B
42110B
1102 &
678 &
910 &
400
400
400
Issue No: 05
Issue Date: 17/08/2016
Page 1 of 7
Advertisement
Related Manuals for Rhino-Rack Pioneer Front Rail Kit
Summary of Contents for Rhino-Rack Pioneer Front Rail Kit
- Page 1 1191 & 446 & 962 & 1102 & 678 & 910 & Rail Lengths (mm) Rhino-Rack 3 Pike Street, Rydalmere, Document No: R034 NSW 2116, Australia. Prepared By: Nigel Greig Issue No: 05 (Ph) (02) 9638 4744 Authorised By: Chris Murty...
- Page 2 Rhino Pioneer Front / Side Rail Kit Care Instruction Tools Required 13mm Spanner Clean alloy tray prior to fitting the Pioneer Rail Kit. Phillips Screwdriver Fit Hardware to Mouldings Loosely fit hardware to all the mouldings as shown. Be sure to set the bolts so they locate half way through the channel nut (see image A below).
- Page 3 Rhino Pioneer Front / Side Rail Kit Fit Cover to Corner Mouldings Fit the corner moulding cover as shown Screw and fasten in place with screws provided in kit. Repeat this process for both corner mouldings. Corner Moulding Cover Corner Moulding Fit First Corner Moulding to End Rail Slide the first corner moulding into the end rail extrusion (long extrusion) and fasten in place with screw (provided in kit).
- Page 4 Rhino Pioneer Front / Side Rail Kit Fit Side Rail Extrusions to End Rail Assembly Slide the side rail extrusions onto the ends of the corner mouldings as shown and fasten with screws. End Rail Assembly Screw Side Rail Extrusion Fit Side Support Mouldings and Rail End Moulding Slide the side supports and end mouldings into the side rail extrusions as shown below and fasten with screws.
- Page 5 Rhino Pioneer Front / Side Rail Kit Engage Side Supports Lift the front of the rail slightly and slide the first side support over the slot in the tray. Lower the channel nut into the slot and slide the side support towards the end moulding.
- Page 6 Rhino Pioneer Front / Side Rail Kit Engage End Supports Slide the rail assembly over the tray until the channel nuts on the end supports locate within the slots at the front of the tray. Now slide the rail assembly towards the front of the tray so the channel nuts engage within the channels. The rail should stop when it reaches the correct position for fitment.
- Page 7 Rhino Pioneer Front / Side Rail Kit Fitment Options Page 7 of 7...
Need help?
Do you have a question about the Pioneer Front Rail Kit and is the answer not in the manual?
Questions and answers