CONTENTS SAFETY USING THE MOUNT ITEM CHECKLIST CHECKING CALIBRATION LASER OVERVIEW TROUBLE SHOOTING REMOTE CONTROL OVERVIEW CARE & MAINTENANCE DETECTOR OVERVIEW WARRANTY USING YOUR LASER CUSTOMER SUPPORT Power Supply SPECIFICATIONS Horizontal Set-up Vertical Set-up Operation Using Your Remote Control Using Your Detector...
SAFETY Read the following safety instructions before • Tool service must be performed only by qualified attempting to operate this product. repair personnel. Repairs, service or maintenance performed by unqualified personnel will void the Keep these instructions in a safe place or store in the warranty.
Page 5
CAUTION: Class 2 Laser Product • Do not let children come in contact with the laser. • Turn the laser off when it is not in use. Leaving • Never look into the laser beam directly and the laser on increases the risk of staring into the intentionally.
ITEM CHECKLIST Please ensure the following items are included with your laser level. If anything is missing please contact your retailer. INCHES Remote Lasertec HV2R Laser glasses Detector & clamp Mount Laser target control 2x AAA alkaline 4x AA rechargeable...
USING YOUR LASER POWER SUPPLY Indoor charger • The indoor charger is for indoor use only. • The instrument is supplied with four AA Ni-Mh batteries as its standard power source. • Do not store in locations where moisture can be present or where the charger could be exposed to • The instrument can also be powered by four AA extreme temperatures.
HORIZONTAL MEASUREMENT SET UP Charging the rechargeable batteries • Insert the charger into the charging port on the Level surface set up instrument. Progress will be shown by the power indicator display on the charger as below: • Select a place as close and practical to the work site as possible, and ensure that the location is Red (flashing) = Charger and battery clear of traffic.
OPERATION Tilt alarm • Once the instrument has been levelled off the tilt Powering on alarm can be enabled by pressing the tilt alarm button on the instrument. The tilt alarm indicator • Press the power button once and the instrument light will flash continuously whilst active.
USING YOUR REMOTE CONTROL • To adjust the grade, press the grade adjustment arrows on the remote control. These arrows will adjust the grade on either the x-axis or y-axis. Power supply • To cancel out of manual mode press the manual / •...
USING YOUR DETECTOR Detector operation Power supply • Switch the detector on by pressing the power The detector is powered by a 9V alkaline battery. • button. The speaker will beep once indicating the instrument is operating. Mounting the staff clamp •...
Page 19
Detector position for horizontal beams Detector position for vertical beams...
USING THE MOUNT OVERVIEW Screw fixing point Screw fixing point Hook 5/8” x 11 thread for 5/8” x 11 thread for vertical operation vertical operation on a tripod on a tripod Locking lever...
Page 21
USING THE MOUNT Mounting via screw fixing points • Attach the mount via the hook onto the back of the instrument. • Push the locking lever to secure in place. • Fix a screw into a secure surface and hook the mount over the screw.
CHECKING CALIBRATION Before doing any precision levelling it is advised to check the calibration of the instrument. • Set up the laser on a tripod at about 30m facing a wall or staff with a detector. • Allow the instrument to level. •...
TROUBLE SHOOTING Error Cause & Solution • Check the batteries. They may be in the wrong way or need replacing. Laser does not • Check the battery compartment for signs of damage. Ensure they are clean and not bent. turn on •...
CARE AND MAINTENANCE • Reflective surfaces such as glass may reflect the • The operator should check the accuracy of the beam, causing two beams to strike the detector instrument before precision levelling is attempted. at the same time. This may create inaccurate Failure to do so may result in inaccurate reference points.
WARRANTY 3 YEAR STANDARD WARRANTY PERIOD 7 YEAR EXTENDED WARRANTY PERIOD 1. The warranty period for your Lasertec tool is 3 1. The extended warranty is available on selected years from the date of purchase. tools only. 2. The warranty period for batteries, battery packs 2.
Page 26
WARRANTY (continued) AUSTRALIA NEW ZEALAND “Our goods come with guarantees that cannot be For more information please visit excluded under the Australian Consumer Law. You consumerprotection.govt.nz are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage.
CUSTOMER SUPPORT To assist you with any queries or technical questions please contact our 24 hour customer support hotline. Australia: 1300 658 338 New Zealand: 0800 367 527...
SPECIFICATIONS Specifications Lasertec HV2R Product code 91340 Warranty 7 Years* Accuracy ±1.5mm at 30m Operating range 250m (diameter) Levelling range ±9% / ±5° Laser class 2 Red Battery life 20 hours Battery type 4x 1.5v AA IP rating Weight (kg) 1.25...