Advertisement
Product Damage
The ignitor must remain in its shield when
removing bar broil burner.
Failure to do so could break ignitor.
F
n
After the burners have been
converted
to Natural
gas usage, complete
Steps 16-17, Panel C and Step 22, Panel D.
Adjusting for proper flame
Product Damage
l
Electric ignitors are used to light the oven
and broil burners. Do Not insert any
object into the openings of the shield
surrounding the ignitor coil.
l
Do Not clean this area.
Failure to follow these instructions could
result in product damage.
A
w Cooktop burners:
Adjust the air
shutters for proper
flame by sliding the air
shutter to close or open the shutter as
needed.
See Panel D, Steps 19-22. Natural
gas has no yellow tip to flame.
B
w Oven burner:
Loosen screw and
adjust the air shutter as needed.
Tighten
screw. See Panel D, Steps 23-25.
C
n
Broil burner:
1, Remove
the two screws fastening
the front
of broil burner to oven. Pull the broil burner
forward.
Loosen the lock screw on the air
shutter located
at the rear of the broil
burner.
2. Adjust air shutter as needed.
The flame
should be l/2" long with inner cone of bluish-
green and outer mantle
of dark blue. The
flame also should be clean
and soft in
character
with no blowing
or lifting of flame,
Tighten the lock screw. See Panel D, Steps
26-27.
Part No. 36-3 14445-02-O/4363404
0 1994 Whirlpool
Corporation
D
H Replace
storaae
drawer,
oven
bottom,
oven racks acd oven door. Reinstall
maintop
and burner grates, burner caps and
burner bases. See Panel D, Step 22.
If range does not
operate...
l
Check
that the circuit breaker
is not
tripped
or the house fuse blown.
l
Check
that power
supply cord is plugged
into wall receptacle.
l
Check
that the gas supply is turned
on.
NOTE:
Refer to Use and Care Guide for operating
instructions and cleaning instructions.
Personal Injury/Product
Damage Hazard
Do Not step, lean or sit on the range
drawer or door.
Failure to follow these instructions
could
result in personal injury and/or product
damage.
For cleaning and
mahtenance...
If removing
the range
is necessary
for
cleaning
and maintenance,
remove
storage
drawer.
Shut off gas supply to range.
Disconnect
gas and electrical
supply.
If gas or electrical
supply is inaccessible,
lift
range slightly at front and pull range
away
from wall. Pull range
out only as far as
necessary
to disconnect
gas and electrical
lines.
Remove
range to complete
cleaning
or
maintenance.
Move range
back into operating
position.
Level range.
Connect
gas line to range and
check
for leaks. Replace
storage
drawer.
w
id1 01
C3FCRWKt.
Prepared
by Whirlpool
Corporation,
Benton Harbor, Michigan
49022
Plug power
supply cord into outlet.
Make sure that rear leveling
leg(s) are
engaged
in anti-tip
bracket(s).
If you need
assistance...
The Whirlpool
Consumer
Assistance
Center
will answer any questions
about
operating
or
maintaining
your range
not covered
in the
Installation
Instructions.
The Whirlpool
Consumer
Assistance
Center
is open
24 hours
a day, 7 days a week. Just dial l-(800)-253-
1301 - the call is free.
When you call, you will need the range
model
number
and serial number.
Both
numbers
can be found on the serial/rating
plate
located
under the maintop.
If you need
servfce...
In the event that your Whirlpool
appliance
should need service,
call the dealer
from
whom
you purchased
the appliance
or a
Whirlpool-authorized
service
company.
A
Whirlpool-authorized
service
company
is
listed in the Yellow Pages under "Appliances
-
Household
-
Major -
Service
and
Repair."
You can also obtain
the service
company's
name
and telephone
number
by dialing,
free, within the continental
United States, the
Whirlpool
Consumer
Assistance
Center
telephone
number,
l-(800)-253-
1301. A
special
operator
will tell you the name
and
number
of your nearest
Whirlpool-authorized
service
company.
Maintain
the quality
built into your Whirlpool
appliance
- call a Whirlpool-authorized
service
company.
Printed on recycled
paper.
10% post consumer
waste/
50% recovered
materials.
Printed in U.S.A.
Advertisement
