Advertisement
Quick Links
This option may have been installed by the factory. However, certain steps can
only be completed at the installation site. Therefore, review and then perform
those steps which will complete the installation process.
Before installing this option, a TECHNICALLY QUALIFIED INDIVIDUAL who is
familiar with this type of equipment and the hazards involved, should READ THIS
ENTIRE INSTRUCTION SHEET.
The NCL Satellite board is an electrostatic sensitive device. Personnel must use
approved methods for handling this type of equipment.
HAZARDOUS VOLTAGE CAN CAUSE SEVERE INJURY OR
DEATH. ENSURE ALL POWER SOURCES FEEDING DRIVE
ARE LOCKED IN THE "OFF" POSITION BEFORE INSTALLING
THIS OPTION.
INTRODUCTION
NCL is a communications network developed by MagneTek to accommodate multiple satellite devices (drives)
from a single PLC network node which serves as a gateway to other networks. NCL protocol is based on CAN
technology, featuring efficient real-time control via master/slave communication capability. NCL supports up to 30
satellite subnodes per gateway. The NCL satellite board will enable the drive to accept serial communication,
allowing the network to perform all functions available via the keypad or external I/O, and to access all drive data.
CHANGE RECORD
NCL SATELLITE
MODEL CM006
NOTE
CAUTION
CAUTION
WARNING
For GPD 333
Adjustable Frequency Drives
DWG. NO. 02Y00025-0385
SHEET NO. 1 OF 4
REL. 7/15/96
( m - df )
Advertisement
Related Manuals for YASKAWA CM006
Summary of Contents for YASKAWA CM006
- Page 1 For GPD 333 Adjustable Frequency Drives NCL SATELLITE MODEL CM006 NOTE This option may have been installed by the factory. However, certain steps can only be completed at the installation site. Therefore, review and then perform those steps which will complete the installation process.
- Page 2 SPECIFICATIONS GPD 333 NCL Satellite Ambient Temperature –10 to +40 degrees C (+14 to +104 degrees F) Storage Temperature –20 to +60 degrees C (–4 to +140 degrees F) Relative Humidity 90% noncondensing Altitude 3300 feet Vibration 1G at less than 20 Hz, 0.2 G at 20-50 Hz Input Power Voltage: 11-25 VAC...
- Page 3 INSTALLATION O 2 @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ 6 K ? O @ K ? e ? O 2 @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ 6 K O @ K O 2 @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ ) X O 2 @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ 6 X ?
- Page 4 DIPSWITCH SETTINGS The dipswitch located on the backside of the NCL Satellite board must be properly set before attempting to establish serial communications. The following table defines the function of each switch position of DIPSW1: Satellite DIPSW Position Switch # Switch Function Baud Rate * 0 = off...