1. Manuals
  2. Brands
  3. Egholm Manuals
  4. Utility Vehicle
  5. City Ranger 2260
  6. Operator's manual

Egholm City Ranger 2260 Operator's Manual

Basic machine
Hide thumbs Also See for City Ranger 2260:
Table of Contents

Advertisement

Quick Links

Operator´s
manual
Basic machine
City Ranger 2260

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the City Ranger 2260 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Egholm City Ranger 2260

Summary of Contents for Egholm City Ranger 2260

  • Page 1 Operator´s manual Basic machine City Ranger 2260...
  • Page 2 We ask you to pay particular attention to section 1.1 Safety. The machine must only be serviced by professionals. The City Ranger 2260 is designed only for use by professionals. On delivery, the user will receive thorough training to become a competent operator.

  • Page 3: Table Of Contents

    3.3 City Ranger 2260 service and maintenance chart ....... . .
  • Page 4 Introduction...

  • Page 5: Introduction

    Introduction The utility machine City Ranger 2260 The City Ranger 2260 is an outdoor utility machine with a complete range of special attachments that allows you to work outdoors, all year round. Sweeping and vacuuming in spring and autumn, mowing grass and lawn-edge cutting in the summer, sweeping snow, and spreading gravel and sand in the winter.
  • Page 6 General information...

  • Page 7: General Information

    Any person who has not read and fully understood the contents of this chapter must not be allowed to operate the Egholm City Ranger 2260. Max. 10°...
  • Page 8 Keep fingers and hands away from Articulated joint the A-frame as there is a danger of crushing. Turn the steering wheel carefully The City Ranger 2260 is articulated – it turns sharply, immediately. (Picture 3) Other hazards There may be other circumstances...
  • Page 9 • The acid contained in the battery is very harmful and very corrosive. Avoid contact with skin and eyes. In case of contact, rinse thoroughly with clear water. • In case of critical injuries, seek medical help. Operator’s Manual City Ranger 2260...
  • Page 10 Operation instructions Cooling fan • Always watch out for the traffic while operating the machine. • The City Ranger 2260 belongs to the category of public work vehicles. This vehicle should not be used for the transport of humans or goods.
  • Page 11 Push the pedal down: The machine drives forward. (Picture 3) Stop: Neutral position. Reverse: Press left and down Drive pedal The machine reverses. (Picture 4) Speed is variably adjusted. See section 1.9. Forward driving Reverse driving Operator’s Manual City Ranger 2260...

  • Page 12: Attachments

    There is an operator’s manual for each attachment. Operation with these attachments must follow the instructions outlined in the relevant operator’s manual. Do not operate the City Ranger 2260 with the attachment unless all instructions have been followed. Operator’s Manual City Ranger 2260...

  • Page 13: Ec Declaration Of Conformity

    Unless otherwise agreed in writing between the operator, customer and Egholm, Egholm is the data originator (data originator) of all data generated by the machine and attachments during use.

  • Page 14: Technical Data

    Machine weight (including cab) ......940 kg Unladen weight - City Ranger 2260 with roll bar ... . . 910 kg Max.
  • Page 15 • Operator seat ............. 87 dB(A) Operator’s Manual City Ranger 2260...
  • Page 16 Seats mounted for vibration test: ..COBO SC79-M97 or SC79-M200 Both seats are approved according Directive 78/764/EEC. Falling Object Protective Structure - FOPS The City Ranger 2260 and its attachments do not operate with processes where falling objects are a risk Roll-Over Protective Structure - ROPS...

  • Page 17: Access To The Cab

    Attention Always lock the machine when leaving. Never leave keys in ignition lock. Cab floor Attention Keep cabin free of loose items that may interfere with safe operation of the machine. Internal door handle Operator’s Manual City Ranger 2260...

  • Page 18: Steering Column

    Turning the ignition key activates the alarm for two seconds, followed by one second pause and activation for two seconds. When the alarm sounds it is repetitive, 2 seconds beep, 30 seconds pause (max 3 beeps). Operator’s Manual City Ranger 2260...
  • Page 19 16. Shows rpm or km/h / mph 17. Engine temperature indicator. Instrument panel – centre Sound alarm activates in case of 6, 9, 10, 11, 12 and 13 Operator’s Manual City Ranger 2260...
  • Page 20 The parking brake is engaged by: Press the brake pedal all the way down. Lift the handle up. Release the brake pedal again. To disengage the parking brake: Press the brake pedal. This frees the handle. 23. Turn signal, trailer. 24. Steering system failure (low steering oil pressure). Operator’s Manual City Ranger 2260...

  • Page 21: Operational Features

    In position 2, the LED blitz front (option) turns on together with the beacon. Attention! The LED blitz must not be on during transport on public roads. Check the local regulations for use of LED blitz in working situations. Operator’s Manual City Ranger 2260...

  • Page 22: Joystick Console

    9. 12 V connector. attachment operator’s manual). 6. PTO rear: Press left for “on”, middle position for “off” and right for start/stop function “Stop & go”. 7. Function. (F2), (attachment specific, See the attachment operator’s manual). Operator’s Manual City Ranger 2260...
  • Page 23 14. Adjusting weight distribution. Adjust the weight distribution until the attachment is weightless. Then adjust the weight transfer until the attachment touches and follows the ground. Adjust further for additional ground pressure from the attachment. 15. Safety cover for fuses. Operator’s Manual City Ranger 2260...

  • Page 24: Pedals

    Forward driving Forward: Push the pedal down: The machine drives forward. (Picture 2) Stop: Neutral position. Reverse: Press left and down The machine reverses. The pedal automatically returns to the neutral position. (Picture 2+3) Reverse driving Operator’s Manual City Ranger 2260...

  • Page 25: Start/Stop Function For Salt And Sandspreader

    General information 1.9 Pedals - continued Advice when driving on a steep slope Users of City Ranger 2260 have reported that, from time to time, they feel that the machine does not accelerate properly when driving up an incline. The machine is designed to drive on an incline of no more than 12°.

  • Page 26: Fuses

    ASS 15 5 Amp ECU starter switch ASS 16. Diode Indication light, horn and steering column. ASS 17 Diode Stop fuel relay + starter Fuses – cabin floor right side Spare 1 Spare fuse. Spare 2 Spare fuse. Operator’s Manual City Ranger 2260...
  • Page 27 20 A JF2 emergency line 30 A JF3 engine power Main switch City Ranger 2260 will not start unless the main switch under the right rear screen is ON (vertical). 60 A JF15 generator - 60 A JF1 supply fuse box...

  • Page 28: Towing

    General information 1.12 Towing Towing When towing City Ranger 2260, attach the tow line to the pull hook on the left side of the machine. (Picture 1) Towing valve The towing valve under the machine is used to move the machine manually. (Picture 2)

  • Page 29: Front Attachment Frame - A-Frame

    The couplings and the area around the couplings must be kept clean to avoid an accumulation of dirt (See section 3.1). Attaching an attachment: see the attachment operator’s manual. C-Coupling Operator’s Manual City Ranger 2260...

  • Page 30: Cab Seat - Mechanical Or Pneumatic Suspension

    (Picture 1) Pneumatic Higher: Adjust by gradually pressing the handle 1 The suspension becomes firmer. Lower: Adjust by gradually releasing the handle 1 The suspension becomes softer. Forwards/backwards: Adjust using the handle 2. (Picture 2) Operator’s Manual City Ranger 2260...

  • Page 31: Cab Heating

    Failure to do so increases the risk of corrosion and bacterial accumulation in the system which can cause discomfort/sickness for the driver. Cabin filter must be checked/cleaned once a year. Operator’s Manual City Ranger 2260...

  • Page 32: Opening And Removing Side Screens

    Lift the side screen off by pulling slightly upwards and remove the screens. The machine is easier to service, when the side screen is removed. (Pictures 3) Light pressure on relase key and side screen Removing side screens Operator’s Manual City Ranger 2260...

  • Page 33: Opening The Loading Frame

    When the loading frame is open the exhaust from the exhaust pipe will heat up the loading frame. If running for a long time it can cause the wiring to melt. (Picture 2) Exhaust Wiring Operator’s Manual City Ranger 2260...

  • Page 34: Removing The Cab/Roll Bar

    (Picture 3) 6. Tip the cabin/roll bar forwards so that the sealing strip can be removed. (Picture 4) Loosen the 2 bolts on each side Bolts under base plate Remove sealing strip Operator’s Manual City Ranger 2260...
  • Page 35 10. Remove the two bolts under the base plate at Pull out the cables the front of the machine. (Picture 2) 11. Lift off the cab/roll bar (min. 2 people). (Picture 3) Bolts under base plate Lift off cab/roll bar Operator’s Manual City Ranger 2260...

  • Page 36: Fitting The Cab/Roll Bar

    Trim off some of the width of the strip adjacent to the holes if necessary. 5. Position spacers. (Picture 4) Bolts under base plate Chock, attach strip Position spacers Operator’s Manual City Ranger 2260...
  • Page 37 (cab only). (Picture 4) 12. Attach the doors to the cab (cab only). 13. If roll bar mounted, remember to fasten topframe of the roll bar. (Picture 5) 3 connectors behind grate Rubber strips Roll bar Operator’s Manual City Ranger 2260...

  • Page 38: Trailer

    General information 1.23 Trailer When City Ranger 2260 is equipped with the approved coupling ”class A50-X approval no. E2-55R-0112208”, the following trailers can be connected: Trailers without brakes max.750 kg Trailers with overrun brakes max.1.610 kg Vertical load on trailer coupling max.100 kg...
  • Page 39 Operator´s manual...

  • Page 40: Operator's Manual

    (Picture 4). Must be visible in the sight glass. (Picture 4) Topping-up – see maintenance section 3.4. Min. Max. Engine oil Hydraulic oil – sight glass Operator’s Manual City Ranger 2260...
  • Page 41 The Gasoline level lamp will only light when the machine is on. Topping-up gasoline Check coolant Tjeck coolant level at sight glass. (Picture 3) Attention Never remove the water cover when the engine is hot. Gasoline level Expansion tank – check coolant Operator’s Manual City Ranger 2260...

  • Page 42: Start, Drive And Stop

    (Look at 1.1. Safety, page 7) • Always drive carefully. • Do not forget that the City Ranger 2260 is a relatively high and narrow vehicle. Turning should therefore be done at a low speed.
  • Page 43 5. Turn the ignition key (clockwise) until the City Ranger 2260 is started. Note: if the City Ranger 2260 is started without having the trottle handle in idle position it is not possible to increase rpm before the handle has been in idle position. Engine warning lamp is on.
  • Page 44 Brake pedal Drive pedal parking lock up (Picture 2) and release the brake pedal (See Section 1.6). 4. Turn off the City Ranger 2260 by turning the key back to the key-release position. Operating with front attachments Before the City Ranger 2260 can drive, the fitted attachments must be lifted clear of the ground.

  • Page 45: Transporting The City Ranger 2260

    Operator’s manual 2.3 Transporting the City Ranger 2260 To transport the vehicle, cross the restraint straps and attach them to the four transport securing rings of the vehicle. (Picture 1+2+3+4) Anchoring at the front Straps at the front Anchoring at the rear Straps at the rear Operator’s Manual City Ranger 2260...
  • Page 46 Service and maintenance...

  • Page 47: Service And Maintenance

    Before starting any maintenance, turn of engine, remove key and set the main switch in off position. Daily maintenance of the City Ranger 2260 is simple, easy and very important. Three things are required: Cleaning the water cooler, oil cooler...
  • Page 48 (Picture 4). Must be visible in the sight glass. (Picture 4) Topping-up – see maintenance section 3.4. Hydraulic oil, check 3.4 Engine oil, check 3.5 Min. Max. Engine oil Hydraulic oil – sight glass Operator’s Manual City Ranger 2260...

  • Page 49: Lubrication

    Greasing Description Acces point 1 - 5 Steering cylinder From underneath 2 - 4 Steering cylinder From right / left side From underneath move Articulated joint protection shield 6 - 7 A-Frame cylinder From underneath Operator’s Manual City Ranger 2260...

  • Page 50: City Ranger 2260 Service And Maintenance Chart

    Service and maintenance 3.3 City Ranger 2260 service and maintenance chart X Lubricate t Clean m Check lReplace Operation Service schedule First Every Every Every Every Every Daily See § 200h 600h 1000h year 2.year Machine Walk-around inspection Tyre Pressure (1)
  • Page 51 Service and maintenance 3.3 City Ranger 2260 service and maintenance chart - continued X Lubricate t Clean m Check lReplace Operation Service schedule First Every Every Every Every Every Daily See § 200h 600h 1000h year 2.year Hydraulic Hydraulic oil...

  • Page 52: Hydraulic System

    Hydraulic oil top-up 1. Park the City Ranger 2260 on a level surface. 2. Switch the engine off. 3. Unscrew filler cap and fill with Texaco HDZ 68 Hydraulic filter oil or similar.

  • Page 53: Engine Maintenance

    Engine oil check 1. Park the City Ranger 2260 on a level surface. 2. Check the oil level before the engine starts. Check the oil level (Picture 1) 3.
  • Page 54 For more information: look at the Kubota manual. Lubricating oil viscosity must be suitable for the ambient temperature range for the climate in which the machine is to operate. (Picture 1) Operator’s Manual City Ranger 2260...

  • Page 55: Fuel

    2. If hoses and hose clamps are worn, they should be immediately replaced. 3. Remove air from the fuel system, if fuel hoses have been replaced. Operator’s Manual City Ranger 2260...

  • Page 56: Cooler

    50% polyethylene glycol, or as prescribed by the manufacturer. 3. Carefully remount the cooler cap. 4. Start the City Ranger 2260 and run the machine until it is sufficiently warm. 5. Switch the engine off and add more coolant.

  • Page 57: Air Filter

    Described in section 3.1. 3.8 Air filter Cleaning the air filter 1. When the City Ranger 2260 is operating in dirty and dusty conditions, open the vacuum valve every Windscreen washer liquid cap day to get rid of larger dirt and dust particles.

  • Page 58: Battery

    + terminal, and the - terminal is Main switch – OFF connected to the battery’s – terminal. Battery fluid level The battery is maintenance free, only check the green lamp on battery. (Picture 4) Green lamp Battery Operator’s Manual City Ranger 2260...

  • Page 59: Generator V-Belt

    100 Nm. Wheel bolts should not be lubricated. Attention Only use tyre dimension and tyre pressure as specified in section 1.4 page Attention Changing tyres on rims may only be carried out at an authorized workshop. Operator’s Manual City Ranger 2260...

  • Page 60: Cabin Filter

    The fitting of the new filter is carried out in reverse order: • filter element. • rubber gasket and steel plate. Steel plate and rubber gasket • foam plate. • grate. (Picture 4) Filter element Filter Rubber gasket Steel plate Foam plate Grate Operator’s Manual City Ranger 2260...

  • Page 61: In Case Of Failure

    It is also advisable to chock the wheels. Call your after-sales service and provide the serial number of your City Ranger 2260. You can read it on the information plate of your vehicle. (Picture 1) 3.15...
  • Page 62 Conditions...

  • Page 63: Conditions

    Conditions 4.1 Warranty The warranty period for the materials and manufacture of this City Ranger 2260 is 12 months from the date of purchase. In case of errors or defects on the machine within the warranty period, Egholm will carry out the necessary repairs without charge for materials and working hours in accordance with the terms and conditions listed below.

  • Page 64: Complaints

    Egholm A/S 4.3 Disposal When, many years from now, your City Ranger 2260 has reached the end of its working life, it should be disposed of in a responsible manner that conforms with relevant disposal regulations. 1. Used hydraulic oil, engine oil, gasoline , coolant and AC coolant are to be delivered at an approved waste disposal facility or site.
  • Page 65 Wearing parts...

  • Page 66: Wearing Parts

    Wearing parts 5.1 Wearing parts - City Ranger 2260 E50000048 Tyre and wheel 2260 E80700343 Filter kit E01006500 Air filter 2200/2260 E01022051 Oil filter 2260 E01002000 Hydraulic filter E01022022 Fuel filter 2260 e70501371 Cab filter 2260 E50007522 AC-belt 2260 incl. sealing band...
  • Page 67 Wearing parts 5.1 Wearing parts - City Ranger 2260 - continued E80700344 Drain plug set Plug and gasket E01022001 Spark plug E05001140 Lightbulb, main light - 287 E05001180 Bulb front work light E05001040 Bulb, parking light E05001010 Bulb for front turn signals E04501320 Hydraulic couplings A+B frame, 1/4”...

  • Page 68: Notes

    Notes Operator’s Manual City Ranger 2260...
  • Page 69 Notes Operator’s Manual City Ranger 2260...
  • Page 70 Notes Operator’s Manual City Ranger 2260...
  • Page 71 Notes Operator’s Manual City Ranger 2260...
  • Page 72 Egholm A/S Transportvej 27 7620 Lemvig, Denmark T.: +45 97 81 12 05 www.egholm.eu - info@egholm.dk...

Table of Contents