Sequence Programming - Whirlpool SF195LEK Use And Care Manual

Sequence Programming

(on some models)
Sequence Programming allows you to program at one time up to
four cook functions, and can be used at the same time with other
oven functions, such as the Timer and Warming Drawer.
Sequence Programming takes precedence over any non-
sequenced cook function. For example, if an un-timed Bake
function is in process and a sequence program is started, the
un-timed Bake function will be canceled, and the program
sequence will start.
All steps of a sequenced program, except for the last step, must
be programmed with a stop time. If a stop time is not entered for
a step in the sequence program, and the FIRST/NEXT STEP pad
is pressed, three tones will sound.
To Program the First Step of the Sequence:
1. Press FIRST/NEXT STEP .
"PROGRAM" and "STEP" will appear on the display. A
flashing "1" will also appear on the display, indicating that
step 1 is being programmed.
2. Choose the desired cook function by pressing any cook
function key.
Press TEMP "up" or "down" arrow pad (if desired) to select
temperature.
3. Press START TIME, then HR and MIN "up" or "down" arrow
pads to set the time of day for the first cook function to begin.
If START TIME is not pressed, then the sequence of cook
functions will begin immediately once programming is
complete and START is pressed.
The display will show either the time of day (if start time was
not programmed) or the start time (if same was programmed),
but with a flashing colon. "Stop" and "Time" will also appear
on the display.
4. Press STOP TIME, then HR and MIN "up" or "down" arrow
pads to set the time of day for the first cook function to stop.
To Program Next Steps of the Sequence:
1. Press FIRST/NEXT STEP .
"PROGRAM" and "STEP" will appear on the display. The
number of the steps being programmed will flash.
"START" and "TIME will appear on the display.
2. Choose the desired cook function by pressing any cook
function key.
Press TEMP "up" or "down" arrow pad (if desired) to select
temperature.
3. Press STOP TIME, then HR and MIN "up" or "down" arrow
pads to select stop time.
4. Press START to begin sequence.
5. Press OFF/CANCEL at any time to clear program and to stop
program.
14
To Review/Modify Programmed Sequence:
If program steps are partially or completely programmed, yet the
sequence has not been started, the programmed cook functions
can be reviewed.
1. Press REVIEW STEPS. Step 1 will appear in the display
Subsequent presses of REVIEW STEPS will cause display of
programmed steps in order.
"STEP" and "RECALL" will appear on the display. The
number of the displayed step will flash. A recalled step will
remain lit on the display for 5 minutes if no further action is
taken.
2. If fewer than four steps have been programmed, press
REVIEW STEPS repeatedly until the last programmed step is
displayed, then press FIRST/NEXT STEP if it is desired to
program an additional step.
While a step is recalled, a cook function pad can be used to
change the function, or the TEMPERATURE "up" or "down"
arrow pad can be used to change the set temperature.
START TIME, when used with the HR or MIN "up" or "down"
arrow pads, can be used to change, add or delete a delayed
start.
STOP TIME can be used to change the stop time. Changing
the stop time of a step will automatically change the start
times and stop times of all subsequent programmed cook
functions.
3. After Review/Modification of the programmed sequence is
complete, press START to begin sequence.
To Modify Sequence Programming:
1. Press UNDO.
The last step of the sequence will be cancelled, and the step
prior to the cancelled sequence will show on the display for
either review or modification.
If the programmed sequence has not been started, see "To
Program Next Steps of the Sequence" section to program a
step to replace the cancelled cook function.
2. Press START.
The first step will show on the display and the program
sequence will begin.
Changes can be made to the STOP TIME during a
programmed cook function; however, changes cannot be
made after a programmed cook function has been
completed.
If at any time during an active sequenced program FIRST/
NEXT STEP is pressed, three tones will sound.