Sequence Programming - Whirlpool GS475LELS2 Use & Care Manual

Table of Contents

Advertisement

To Set a Delayed Timed Cook:
Before setting, make sure the clock is set to the correct time of
day. See "Clock" section.
1. Press desired cook function.
Press the TEMP "up" or "down" arrow pads to enter a
temperature other than the one displayed.
2. Press START TIME.
3. Press the HR and MIN "up" or "down" arrow pads to enter
the time of day to start.
4. Press STOP TIME (optional).
5. If STOP TIME has been pressed, press the HR and MIN "up"
or "down" arrow pads to enter the desired time to end
cooking.
6. Press START.
"DELAY" will appear on the display.
When the start time is reached, the oven will automatically
turn on.
When the stop time is reached (if programmed), the oven will
shut off automatically and "End" will appear on the display.
End-of-cycle
tones will sound, then, if on, reminder tones will
sound every minute.
7. Open and close the oven door to clear the display and/or
stop reminder tones.
Sequence Programming allows you to program at one time up to
four cook functions, and is usable with other electronic oven
control functions, such as the Timer and Warming Drawer.
Sequence Programming takes precedence over any non-
sequenced cook function. For example, if an untimed Bake
function is in process and a sequence program is started, the
untimed Bake function will be canceled, and the program
sequence will start.
All steps of a sequenced program must be programmed
with a
stop time. If a stop time is not entered for a step in the sequence
program, and the FIRST/NEXT STEP pad is pressed, three tones
will sound.
To Program the First Step of the Sequence:
1. Press FIRST/NEXT STER
"PROGRAM"
and "STEP" will appear on the display. A
flashing "1" will also appear on the display, indicating that
step 1 is being programmed.
2,
3.
Choose the desired cook function by pressing any cook
function key.
Press START TIME, then HR and MIN "up" or "down" arrow
pads to set the time of day for the first cook function to begin.
If START TIME is not pressed, then the sequence of cook
functions will begin immediately once programming
is
complete and START is pressed.
The display will show either the time of day (if start time was
not programmed) or the start time (if same was programmed),
but with a flashing colon. "Stop" and "Time" will also appear
on the display.
4. Press STOP TIME, then HR and MIN "up" or "down" arrow
pads to set the time of day for the first cook function to stop.
To
1.
Program Next Steps of the Sequence:
Press FIRST/NEXT STER
"PROGRAM"
and "STEP" will appear on the display. The
number of the steps being programmed
will flash.
"START" and "TIME will appear on the display.
Choose the desired cook function by pressing any cook
function key.
Press TEMP "up" or "down" arrow pad (if desired) to select
temperature.
3. Press STOP TIME, then HR and MIN "up" or "down" arrow
pads to select stop time.
4. Press START to begin sequence.
5. Press CANCEL at any time to clear program and to stop
program.
To Review/Modify
Programmed
Sequence:
If program steps are partially or completely programmed,
yet the
sequence has not been started, the programmed
cook functions
can be reviewed.
1. Press REVIEW STEPS. Step 1 will appear in the display
Subsequent presses of REVIEW STEPS will cause display of
programmed
steps in order.
"STEP" and "RECALL" will appear on the display. The
number of the displayed step will flash. A recalled step will
remain lit on the display for 5 minutes if no further action is
taken.
If fewer than four steps have been programmed,
press
REVIEW STEPS repeatedly until the last programmed
step is
displayed, then press FIRST/NEXT STEP if it is desired to
program an additional
step.
While a step is recalled, a cook function pad can be used to
change the function, or the TEMPERATURE "up" or "down"
arrow pad can be used to change the set temperature.
START TIME, when used with the HR or MIN "up" or "down"
arrow pads, can be used to change, add or delete a delayed
start.
STOP TIME can be used to change the stop time. Changing
the stop time of a step will automatically
change the start
times and stop times of all subsequent
programmed
cook
functions.
3. After Review/Modification
of the programmed
sequence is
complete, press START to begin sequence.
To Modify Sequence
Programming:
1. Press UNDO.
The last step of the sequence will be canceled, and the step
prior to the canceled sequence will show on the display for
either review or modification.
If the programmed
sequence has not been started, see "To
Program Next Steps of the Sequence" section to program a
step to replace the canceled cook function.
2. Press START.
The first step will show on the display and the program
sequence will begin.
Changes can be made during a programmed
cook function;
however, changes cannot be made after a programmed
cook
function has been completed.
If at any time during an active sequenced program FIRST/
NEXT STEP is pressed, three tones will sound.
13

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents