Sam Cook Masterchef Line Executive PSC-40 User Manual page 30

of 5 for 5 seconds, and then changes to
speed 8 for 10 seconds and at the end,
the device is operati ng at H level of its
speed (maximum).
� A SOUP: Select this program to
process soups, the rotary speed starts
from 1 up to H within 9 seconds, and
then the appliance starts to operate
at maximum speed for 3.5 minutes.
� NUTS: Select this program to process
nuts, the rotary speed starts from 1
up to H within 5 seconds, and then the
appliance starts to operate at maximum
speed for 1 minute
USING CUP BLENDER
NOTE! Do not put or remove the blender jug
while the appliance is running.
1. Place the blender housing ① on a dry, hard
and even surface.
2. Using the handle ③, lift the blender
dome ②.
3. Aft er making sure that all blender jug parts
are assembled correctly, put the blender
jug ④ on the blender enclosure ①.
4. Cut the products into smaller parts to make
mixing easier. Put ingredients into the jug
only when the motor is stopped.
NOTE! Do not fi ll the jug above the mark of
2000 ml ④.
5. Att ach the jug cover with cap. The cover in
the jug ⑥ should be depressed to the stop
whereas the cap ⑧ should be inserted with
tongues placed in grooves of the cover and
turned fully clockwise. Make sure the jug
3 0
� SAUCE: Select this program to process
sauce, the rotary speed starts from 1
up to 5 within 3 seconds, and then the
appliance starts to operate at speed 5
for 2.5 minutes
� SMOOTHIE: Select this program to
process smoothies, the rotary speed
starts from 1 up to H within 9 seconds,
and then the appliance starts to operate
at maximum speed for 1 minute.
C. START/STOP Press this butt on if you want
to start or stop the blender operati on.
D. PULSE Press and hold this butt on to set
your appliance to operate at maximum
speed.
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
cover handles are both sides of the appli-
ance aft er the assembly of the cover.
6. Close the blender dome ②.
7. Plug the appliance into the power supply
socket.
The appliance indicates the power supply
by a single beep and momentary illumina-
ti on of all functi on keys and a LCD display,
then the POWER (A) butt on starts lighti ng.
8. The appliance is ready for operati on.
9. Press the POWER (A) butt on. All functi on
butt ons and LCD display are highlighted.
The display will show the initi al setti ngs
(speed at level - 5, ti me - 20 sec)
10. The appliance can be acti vated in two ways:
in automati c or manual mode.
For the automati c mode and functi on selec-
ti on, press the butt on MENU. Each press of
the butt on changes the selected program.
Aft er selecti ng one of six programs, you
must press the butt on START.
It works in a pulse mode, only while you
hold this butt on.
E. SPEED +/- Butt ons to adjust speed (1-9 and
H, where H is the maximum speed)
F. TIME +/- Butt ons to adjust operati on ti me
(5 seconds-30 minutes every 5 sec) with a
sound signal to indicate the end of appli-
ance operati on
G. Indicators of Speed / Time / Program
selected.
To quickly increase or decrease the opera-
ti on speed/ti me, press and hold the butt on
to increase or decrease speed/ti me ("+" or
"-").
The appliance starts up and performs
the selected program. You can stop the
appliance at any ti me by pressing the but-
ton STOP.
Manual mode starts with the selecti on of
the appliance operati on speed by pressing
butt ons SPEED, [+] and [-] to set the motor
rpm. Then by pressing butt on
the operati on ti me in the range from 5
to 30 min. Aft er selecti ng the rpm and
operati on ti me, press the butt on START.
The appliance starts up and performs the
selected operati on program. You can adjust
the operati on speed (rpm) while the appli-
ance is running.
You can stop the appliance at any ti me by
pressing the butt on STOP.
11. If you need to add ingredients when the
cup blender is running, remove the hole
plug (cap) from the lid (cover) and feed the
TIME
select