Audio Setup; Radio Operations - Clarion FZ502 Owner's Manual & Installation Manual

System Setup
The procedure to delete this code is same as
the way of setting the code.
Note:
• Write down your Code in case you forget
it.
• If you have lost your Personal Code,
please contact Clarion customer service.
• The CODE screen will be displayed when
turning the ACC power on after performing
the following operations:
• The car battery was replaced.
• The backup power was cut off.
• The RESET button was pressed.
• When you enter a wrong Personal
Code, the message "LOCK - - - -" is
displayed and the Personal Code entry
is prohibited for a while.
This prohibited time is changed according to
the number of times of wrong code entry as
follows:
• 1 to 6 times: 15 seconds
• 7 times or more: 15 minutes

Audio Setup

SOUND
Press the [CONTROL] knob to choose
SOUND. First press shows current EQ.
Rotate the [CONTROL] knob to choose
BEAT EQ in this order:
OFF -> B-BOOST -> IMPACT -> EXCITE ->
CUSTOM
To change CUSTOM setting, and press
the [CONTROL] knob (center), then press
[CONTROL] knob (right/left) to select EQ
effects including: BASS-G -> BASS-F ->
BASS-Q -> MID-G -> MID-F -> MID-Q
-> TREBLE-G -> TREBLE-F, rotate the
[CONTROL] knob to select a value.
BASS-G / MID-G / TREBLE-G: (-7)- (+7)
BASS-F: 50 / 100 / 200
BASS-Q : 0.7 / 1.0 / 1.4 / 2.0
MID-F: 500 / 1 K / 2 K
PANDORA: ON/OFF
Select OFF if the Pandora application has
not been installed on your iPod touch or
iPhone.
12/24H
Rotate the [CONTROL] knob to choose time
format: 12 or 24 hours.
S-CTRL (iPod mode) : ON/OFF
Rotate the [CONTROL] knob to choose
S-CTRL (Simple control) ON or OFF.
* Refer to P11.
MID-Q: 0.7 / 1.0 / 1.4 / 2.0
TREBLE-F: 5 K / 10 K / 15 K
TREBLE-Q: 0.7 / 1.0 / 1.4 / 2.0
Then press the [CONTROL] knob (left /
right) to select USER preset including:
BALANCE -> FADER -> M-B EX ->HPF(high
pass filter) -> LPF(low pass filter) -> S-W
V O L ( S u b w o o f e r V o l u m e ) , rotate the
[CONTROL] knob to select a value.
BALANCE:LEFT 1-7->CENTER->RIGHT
1-7
FADER:FRONT 1-7->CENTER->REAR 1-7
M-B EX: ON/OFF
HPF: THROUGH/60/90/120
LPF: THROUGH/60/90/120
SUBW VOL: (-6)-(+6)

Radio Operations

Select tuner as playing source
Press the [CONTROL] knob or [SRC / ]
button on the remote control to switch to the
RADIO source.
Select one radio band
Press the the [CONTROL] knob (up long
press) on the panel or [BAND/TOP] button
on the remote control to select one radio
band among FM1, FM2, FM3 and AM.
Manual tuning
During manual tuning, the frequency will be
changed in steps.
Press [CONTROL] knob (left/right) on the
] buttons on the remote
panel or [ ,
control to tune in a higher / lower station.
Auto tuning
Press and hold [CONTROL] knob (left/right)
] buttons the remote
on the panel or [ ,
control to seek a higher / lower station.
To stop searching, repeat the operation
above or press other buttons having radio
functions.
Note:
When a station is received, searching stops
and the station is played.
Preset scan
Preset scan receives the stations stored
in preset memory in order. This function is
useful when searching for a desired station
in memory.
1. Press the [SCN/PS/AS] button on the
remote control.
2. When a desired station is tuned in, press
the [SCN/PS/AS] button on the remote
controlagain to continue receiving that
station.
Note:
Be careful not to press and hold the
[SCN/PS/AS] button, otherwise the auto
store function is engaged and the unit starts
storing stations.
Auto store
Only stations with sufficient signal strength
will be detected and stored in the memory.
Press and hold the [SCN/PS/AS] button on
the remote control to start automatic station
search.
To stop auto store, press other buttons
having radio functions.
Notes:
1. After auto store, the previous stored
stations will be overwritten.
2. The unit has 4 bands, such as FM1, FM2,
FM3 and AM. FM3 and AM can store
by AS function. Each bands can store 6
stations, FZ502 can store 24 stations in
total.
Manual store
When one expected radio station has been
detected, press and hold number button
on the remote control 1-6 to store it in the
memory.
Recall the stored stations
Press one numeric button among 1 to 6 on
the remote control or on the panel to select
the corresponding stored station.
Local seeking
When LOCAL seeking is on, only those
radio stations with strong radio signal could
be received.
Refer to System Setup page 5.
Note:
The number of radio stations that can be
received will decrease after the local seeking
mode is on.
FZ502 6