Table of Contents
Advertisement
HD Radio Operations
HD Radio multicast channels
To tune to an HD Radio multicast channel,
tune to the main signal and then press the
[CONTROL] knob on the panel. PTY and
SUB CH are displayed. Select PTY or SUB
CH by rotate [CONTROL] knob and push to
confirm.
• Select PTY type from the category list by
rotate [CONTROL] knob and push.
• Select SUB CH by rotate [CONTROL]
knob and push.
• Multi channel is available when a digital
signal is detected, the DIGITAL icon will
illuminate. If the digital signal becomes
unavailable, the unit will revert to Analog
reception.
Preset stations
Up to six stations on each band can be
stored as presets, which can then be instantly
recalled by pressing the associated preset
button. To store a station, turn the radio on
and select the desired band and station.
Press and hold the desired preset button
(numbered one through six on the remote
control). When stored, the preset number
will appear in the display. The station is now
stored and can be recalled by pressing the
corresponding preset button. Repeat for the
remaining five presets on the current band
and for presets on the other four bands.
®
iTunes
Tagging
®
Tagging, which
The unit offers iTunes
allows the user to "Tag" songs playing on
HD Radio™ stations for purchase later
through iTunes. When press [ISR] button on
the remote contorl, the unit stores the title
and artist song information that can then be
transferred to your iPod when connected to
the unit. A list titled "Tagged" will appear in
iTunes, allowing you the option to purchase
your tagged songs.
9
FZ502
Note:
Multicast stations can be stored as
presets, but the unit must be in Digital or
Auto reception mode to receive them.
Preset scan
Press [SCN/PS/AS] button on the remote
control to scan and play all preset stations
for 10 seconds each. Press [SCN/PS/AS]
button on the remote control again to stop
scanning and play the current station.
Note:
Be careful not to press and hold the
[SCN/PS/AS] button on the remote control,
otherwise the auto store function is engaged
and the unit starts storing stations.
Automatic store (AS)
Press the [SCN/PS/AS] button on the remote
control to select six strong stations and store
them in the FM3 or AM band using the auto
store function. After entering the stations into
memory, the unit will automatically stop at
each station for five seconds, allowing you to
preview each selection. When using the auto
store function, the new stations replace any
stations already stored in preset memory.
Note:
You can stop the auto store function at any
time by pressing the [SCN/PS/AS] button on
the remote control again.
Note:
T a g g i n g " f u n c t i o n w o r k s b y
" i T u n e s
®
connecting THD301 (sold separately).
iPod compatibility
For detailed information on the playable iPod
models, see our home page: www.clarion.
com
®
iTunes
Tagging
Note:
• iPhone can also be connected to this system
and "iPod" appearing in this manual should
be referred to as "iPod/iPhone".
• This system will not operate or may operate
improperly with unsupported versions.
Tagging music
To begin tagging music, tune to an HD Radio
station. The DIGITAL icon at the display must
be illuminated, indicating a digital station
is being received. TAG icon lights up when
Tagging function is ready. Press the [ISR]
button on the remote control. The tagging
function is highly depends on the receptions
of the radio station. If the channel reception
is insufficient, it will effect the operation of the
tagging function.
"Stored Tag ## of 64" will appear in the
display. The song information is saved to the
unit memory until your iPod is connected. You
can tag up to 64 songs before the tags must
be transferred to your iPod or deleted. When
the Tag memory reaches capacity (64 tags)
the bottom of the screen displays "Memory
Full".
Table 5: TAG Messages
Tag Message
Reason
S T O R E D T A G # #
If the Tag data is ready, and
[ISR] button on the remote
OF 64
control is pressed
SENDING HD TAG
Tag data is sending to iPod
##
MEMORY FULL
Tag storage is full
Tag data is not available
TAG DATA IS NOT
AVAILABLE
IPOD FULL
iPod memory is full
TAG NOT SUPPORT When connect and press
[ISR] button on the remote
control, the iPod without
Tagging function
Note:
Tags saved to your iPod can be managed
using the iTunes software, available at www.
apple.com/itunes.
Downloading tags to your iPod
To download tags to your iPod, plug your
iPod into the unit. All existing tags are
automatically transferred to the iPod and
deleted from the head unit's memory.
If your iPod is connected when a song
is tagged, the Tag will be immediately
transferred to the iPod.
Note:
When transferring Tags to your iPod, the
unit must remain in HD RADIO mode. To
purchase tagged songs, you must sync
your iPod to iTunes and then click the
"Tagged" list on the left side of the iTunes
software screen. Click the "view" button for
purchasing information.
Notes:
1. H o w t o e n t e r t h e i T u n e s t a g g i n g
function?
"TAG" and "DIGITAL" light up when
Tagging function is ready, press [ISR]
button on the remote control to start
iTunes Tagging.
2. What is seen on the radio's display to
let me know I have tagged the tune?
Press [ISR] button on the remote control
to show "STORED TAG## OF 64". After
connect to your iPod, the display shows
"SENDING HD TAG##".
If no connection, the display will show
"STORED TAG## OF 64". You could
save 64 Tag into E2PROM in total.
When you connect to your iPod, Tag
information will be saved in the iPod,
a n d t h e d a t a i n E 2 P R O M w i l l b e
cleared.
3. Then how do I get the tagged tune from
my iPod to the computer?
If you have install iTunes, connect your
iPod to your computer and buy songs
online.
Advertisement
Table of Contents
