Advertisement

XIEGU G90 CHEAT SHEET
This cheat sheet is intended to augment the current G90 user manual and reflects the G90's functionality in version 1.71 of its
firmware. Significant changes with V1.71 are indicated
there are a few versions of the G90 user manual so the page numbers cited here may vary depending on the manual you have.
11/1/19 KE8WO
BASIC
CONTROLS AND
BUTTONS

Power Button

Power on or off
turn the
"Vol"
This rotary control sets the
audio output level
speaker or headphones.
Unmarked Lower
This is a
control ('MFC')
Left Rotary Control
('MFC')
variety of purposes.
New in V1.71: Set DSP filter
center frequency and
bandwidth.
the G90 and
Longer press to power on the G90
display off
Longer press to power off the G90
A short press will turn off the G90 display, but the radio continues to operate. A short press or
using any other G90 control will restore the display.
Note: press this control to route the audio signal to headphones or other audio device plugged into
from the
the headphone icon jack on the left side of the G90.
multifunction
.A short press of the MFC begins a DSP filter configuration process:
used for a
Note: A short MFC press allowed setting the squelch in the prior firmware release. This is
no longer available. See the long MFC button press Squelch level setting below.
Long press the MFC to bring up 5 choices that may be selected for basic use when the MFC is
rotated: Rotate the tuning control to select the desired choice from the five. Press the 'CMP' button to
save the selection. The choices are:
this way.
See the full V1.71 release notes at the end of this document. Note
With the first MFC press, a display of "Cxxx"("xxx" is the center freq) with a
vertical green line at the center allows using the MFC to set the filters center
frequency.
With the second MFC press a display of "Bxxx"("xxx" is the bandwidth) with two
vertical green lines at the sides allows using the MFC to set the filter's bandwidth.
The last press of the MFC completes the process.
100 KHZ frequency step size. This allows quickly adjusting the received frequency in
100KHZ steps with the tuning control. This 100KHZ step size is fixed. This is the initial,
default setting for the MFC.
Squelch level setting. This brings up the squelch level setting where the tuning control can
select the desired squelch setting. Pressing the tuning control saves the squelch setting,
PO Level ... quickly adjust the power output level with the tune control. Then press the tune
control to save the power setting.
Key Speed ... use the tune control to set the CW keying speed. Press the tune control to
save the setting.
FFT Scale ... use the tune control to set the base line of the FFT display up or down,
the MFC three times to complete this new FFT scale setting.
1
Press

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the G90 and is the answer not in the manual?

Questions and answers

Summary of Contents for XIEGU G90

  • Page 1 See the full V1.71 release notes at the end of this document. Note there are a few versions of the G90 user manual so the page numbers cited here may vary depending on the manual you have. 11/1/19 KE8WO...
  • Page 2 New in V1.71: Factory To complete a factory reset of the G90 press and hold the "FUNC" key and power on the G90. Then Reset G90 press the "PRE" key to confirm the reset or press the "VM" key to cancel the reset.
  • Page 3  A long press of the KEY button will change the bottom portion of the display where the G90 will attempt to decode and display the characters as CW is being received. Another long press will turn it off.
  • Page 4 Press the tuning control to end this process at any point.  “AGC” Button Press this button multiple AGC is a feature to attempt to keep the audio levels produced by the G90 at a constant level. times to control the There are four possible settings: ...
  • Page 5 Note: There is apparently some interaction of the filters settings with the cw sidetone frequency. FUNC Button and This button sequence allows See page 23 of the current G90 user manual for a good description of how to use this feature. You then “AGC”/ “SPL” setting up the G90 to use...
  • Page 6 See page 16 of the G90 user manual. VOX also usable with using AF In via the ACC port. Notes: Set up for digital  Digital modes require that the audio in and audio out signals to and from the G90 is by way of the modes rear ‘ACC’ connector. ...
  • Page 7  display.. Depending on the The G90 I/Q is via the stereo 3.5 mm port and is a low level AC signal on the order of 50 or so sound card sample rate, the millivolts or 100 millivolts peak to peak spectrum may be at least ...
  • Page 8 Select the desired bandwidth / sample rate to be used Select ‘Run’ to begin the display  A sample rate of 48,000 will yield a spectrum the same width as the G90’s front panel display, +/- 24 KHZ  A sample rate of 96,000 will yield a spectrum double the width of the G90’s front panel display, +/- 48 KHZ or nearly 100 KHZ! ...
  • Page 9 XIEGU G90 CHEAT SHEET  Sample HDSDR Note: Below is an example of a computer spectrum display of the G90 IQ signal. Very noisy. Ferrites Same setup as above Screen With Noise on the power supply and signal leads did not help this. However, an inexpensive Ground Loop example ...
  • Page 10 XIEGU G90 CHEAT SHEET Full release notes New Features: for firmware V1.71 1.RF GAIN: Long press "AGC" key to access.Rotate main knob to change its value. Note:"RF GAIN" won't affect the S-Meter and FFT Scale. 2.Tuning Steps behavior is changed(from left to right) 3.DSP filter Center/Bandwidth mode...

Table of Contents

Save PDF