Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for MTI BASICS Series
Summary of Contents for MTI BASICS Series
- Page 1 M T I B A S I C S W a l k - i n T u b ® O W N E R ’ S M A N U A L I N S T A L L A T I O N G U I D E E f f e c t i v e J a n u a r y 1 , 2 0 1 1 Installer: This booklet must be given to the product owner.
-
Page 2: Table Of Contents
OWNER’S MANUAL AND INSTALLATION GUIDE Thank you for purchasing an MTI Baths BASICS series Walk-in Tub. You have chosen a high-quality bath, hand-crafted with pride in the USA. The instructions in this booklet will provide you with the information you need to install and operate this unit. Please... -
Page 3: Important Safety Instructions
I M P O R T A N T S A F E T Y I N S T R U C T I O N S WARNING - WHEN USING ELECTRICAL PRODUCTS, BASIC PRECAUTIONS SHOULD BE FOLLOWED, INCLUDING THE FOLLOWING: This manual contains information and instructions for proper operation and maintenance of your bath. -
Page 4: Installation Instructions
Do not store tub in temperatures below 32 degrees Fahrenheit. Proper waste and overflow installation is the responsibility of the installer. MTI does not warrant leaks associated with improper waste and overflow installation. -
Page 5: Electrical Installation Instructions
WARNING: When installing or using electrical products, basic precautions should always be followed, including: 1. All MTI BASICS walk-in tubs equipped with a whirlpool or air bath require a separate 15 amp 110 VAC circuit for each 5.9 amp pump or blower. Radiance tub shell heating system adds 5 amps. -
Page 6: General Installation Guidelines
Completely install the drain assembly and check for leaks prior to the final installation. MTI Baths is not responsible for leaks associated with improper installation or testing of drain. Additional installation information for walk-in tubs equipped with optional valve package Package includes hot &... -
Page 7: General Operating Procedures - Soakers, Whirlpools & Air Baths
Optional Equipment Operating Instructions Inline Heater for Whirlpools - The factory installed inline heater used on MTI whirlpool systems is de- signed to maintain the water temperature during the hydrotherapy bath. The heater is not designed to heat cold water. The heater will activate with the pump with no external switch required. The thermostat is pre-set at 102 ○... -
Page 8: Troubleshooting
T R O U B L E S H O O T I N G Please use the following guidelines if you encounter a problem with your MTI BASICS walk-in tub. These are not covered under warranty but are simple repairs. -
Page 9: Cleaning Instructions
For deeper scratches, sand the surface lightly with a 400 grit “wet or dry” paper and buff with a fine grit buffing compound. MTI strongly recommends using a professional acrylic repair person for deep scratches or chips CLEANING INSTRUCTIONS FOR WHIRLPOOL SYSTEMS THE WHIRLPOOL SYSTEM SHOULD BE CLEANED PERIODICALLY. -
Page 10: Residential Warranty
The bath must be water tested for operation and leaks prior to final enclosure of the unit. Failure to do so will void warranty. If a problem is discovered after the final enclosure, MTI will not be responsible for the cost of removing or reinstalling the tub, or for the costs associated with any adjacent materials. -
Page 11: Commercial Warranty
The bath must be water tested for operation and leaks prior to final enclosure of the unit. Failure to do so will void warranty. If a problem is discovered after the final enclosure, MTI will not be responsible for the cost of removing or reinstalling the tub, or for the costs associated with any adjacent materials. - Page 12 Manufactured by MTI Baths, Inc. mtibaths.com 670 N. Price Road Sugar Hill, GA 30518 800 783 8827 770 271 8228 Fax 800 438 8827 © Copyright 2014 by MTI Baths, Inc. Modification Rights Reserved. 0114...
Need help?
Do you have a question about the BASICS Series and is the answer not in the manual?
Questions and answers