Bosch SHU43E Installation Instructions Manual
Bosch dishwasher
Hide thumbs
Also See for SHU43E:
- Use and care manual (49 pages) ,
- Installation instructions manual (34 pages) ,
- Installation instructions manual (19 pages)
Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Bosch SHU43E
Summary of Contents for Bosch SHU43E
- Page 1 DISHWASHER Installation Instructions LAVE-VAISSELLE LAVADORA DE PLATOS Instructions Instrucciones d’installation de instalación On/Off SHI66A, SHU33A, SHU43C, SHU53A, SHU66C, SHU43E, SHU53E, SHU66E, SHV46C, SHV66A, SHX33A, SHX46A, SHX46B, SHX56B, SHY56A, SHY66C...
-
Page 2: Table Of Contents
MATERIALS SUPPLIED ..4 CHOOSING LOCATION ..5 PLUMBING PREPARATION ..6 ELECTRICAL PREPARATION ..7 PLACING THE DISHWASHER ..8 DRAIN HOSE CONNECTION ..9 HOT WATER CONNECTION ... 10 ELECTRICAL SUPPLY CONNECTION ... 11 GROUNDING INSTRUCTIONS ... 11 DOOR PANEL INSTALLATION ... -
Page 3: Introduction
C22.1 -latest edition/Provincial and Municipal codes and/or local codes. Please read these installation instructions completely and carefully . They will save you time and effort and help to ensure optimum dishwasher performance. Be sure to observe all listed warnings and cautions. (Look for the triangles with exclamation marks inside.) -
Page 4: Tools And Materials Needed
(30” or sufficient length for your installation). Hot Water Supply Line - Minimum 3/8” O.D. copper tubing or metal braided dishwasher supply line. Shut-off valve and fittings for hot water supply line. 90° elbow with 3/8” N.P.T. external threads on one end and sized to fit your water supply line on the other end. -
Page 5: Materials Supplied
MATERIALS SUPPLIED Accessory Parts Supplied Accessory Parts for your model dishwasher will come in one or more plastic bags. Check to make sure that the parts supplied for your model are all there. See Figure 3. If any parts are missing contact your dealer immediately. -
Page 6: Choosing Location
Figure 5. If the dishwasher is to be installed in a corner, make sure there is adequate clea- rance to open the door. See Figure 6. Figure 4 23-9/16”... -
Page 7: Plumbing Preparation
Figure 9. 1. In order to reduce running time, Bosch recommends 140° F water inlet temperature. Your dishwasher will perform equally as well at 120° F water temperature, but the run time will be extended. 6 - ENGLISH... -
Page 8: Electrical Preparation
120V, 60 Hz, AC, connected to a dishwasher-dedicated electrical circuit with a fuse or breaker rated for 15 amps. If the dishwasher is connected with a food disposer, a 20 amp (and no higher) fuse or circuitbreaker may be used. No other appliances or outlets should be connected to the dishwasher supply circuit. -
Page 9: Placing The Dishwasher
(see Figure 11). • Level & Align (initial adjustments). • Guide the drain hose carefully (avoiding kinks in hose) as the dishwasher is slid into the cabinet opening. • Make final leveling adjustments (see FINAL STEPS Section). -
Page 10: Drain Hose Connection
(Figure 14). Openings for drain lines must be installed in the marked areas as shown in Figures 8 and 9 to avoid interference with the dishwasher frame or other components. CAUTION Failure to provide the proper drain connection height, 20” (508mm) -
Page 11: Hot Water Connection
• If using a solder joint instead of a com- pression fitting, be sure to make all solder connections before connecting the water line to the dishwasher . • Make sure there are no sharp bends or kinks in the water line which might restrict water flow. -
Page 12: Electrical Supply Connection
The dishwasher must be properly grounded before operating. Make sure that the dishwasher is connected to a suitable... -
Page 13: Door Panel Installation
Accessory Panel Installation SHU Models If you have an SHU model and have ordered an accessory panel kit it must be installed prior to sliding the dishwasher into place. Dimensions of panel size that may be used is shown in Figure 19. - Page 14 DOOR PANEL INSTALLATION SEE FOLDED PANEL INSTALLATION TEMPLATE SHEET FOR STEP BY STEP INSTRUCTIONS ON HOW TO INSTALL YOUR DISHWASHER PANEL(S). " " A " " B " 6 " 6 Table 2 - " - " Table 3 25”...
-
Page 15: Door Tension Adjustment
FINAL ADJUSTMENTS Door Tension Adjustment (only in SHI and SHV models) After installation of the dishwasher, open and close the door several times to make sure that it does so with ease. If the door closes too quickly or if the door falls open, the spring tension needs to be adjusted. -
Page 16: Base And Toe Panel
(Figure 26). • Drop screws inside holes in base part. • Slip Base Part under and up front bottom panel of dishwasher. Tighten Base Part Screws - LOW TORQUE, USE HAND TOOL ONLY. • Slip Cotton Insulation Strip under unit, between the bottom of Base Part and the floor. -
Page 17: Toe Panel And Handle
• Obtain Toe Panel Screws from the Dishwasher Installation Kit bag (see Figure 3). • Insert screws through the Toe Panel. • With a Torx screwdriver, fasten screws and toe panel into dishwasher base. 16 - ENGLISH Figure 28 www.boschappliances.com... -
Page 18: Final Checklist
120°F-140°F (49°C-60°C). Operate the dishwasher through one cycle and check for plumbing leaks. If the dishwasher does not operate properly, refer to the SELF- HELP, CUSTOMER SERVICE and WARRANTY sections in the Use and Care Manual. Customer Service Information If service becomes necessary, contact your dealer or installer or an authorized service center. - Page 19 18 - ENGLISH www.boschappliances.com...