Table of Contents
Advertisement
Available languages
Available languages
USE
•
Pull the cord (4) out of the appliance. The cord must not be pulled out any
further than the red mark. Plug in and switch on the power.
•
Press the on/off button (1) to start and stop the appliance.
•
Press the lock button (16) on the tube and push or pull the tube to the required
length.
•
Suction strength can be regulated by opening and closing the air vent (23) on
the handle.
o When the vent closes full suction is achieved. This is the normal setting.
o When the vent opens, more air is allowed in, reducing suction power at the
floor nozzle. This function is for cleaning curtains and other light items which
can get sucked into the nozzle.
•
The floor nozzle brushes (11) have two settings, which can be selected using the
brush switch (12).
o When cleaning hard surfaces (stone or wooden flooring, tiles, lino etc.), the
nozzle brushes should be extended.
o When cleaning carpets and rugs, the brushes should be retracted into the
nozzle.
•
IMPORTANT! If the suction strength of the appliance is reduced, the nozzle,
hose or dust container suction may be blocked, or filters may be blocked or
dirty. Never use the appliance if this is the case, as this will damage the motor
irreparably. Remove the cause of the blockage or clean the filters.
•
IMPORTANT! The appliance is provided with thermostatically controlled
overheat protection that automatically shuts off the motor in case of blockage.
If this happens, turn off the appliance and unplug it. After 30 minutes, the
appliance will have cooled off and will be ready to use when you have removed
the blockage.
Tips
•
There is a nozzle holder (22) on the telescopic
tube for storage of the brush nozzle (13) and
crevice nozzle (14) when these are not in use
(see photo).
•
Each nozzle has a special purpose. Experiment
in order to discover which nozzle functions
best in different situations. The brush nozzle
is suited to vacuuming corners and crevices
because it rotates.
•
If you want to take a break while vacuuming, you can insert the parking bracket
on the back of the floor nozzle (17) or on the tube (17) in the parking holder at
the back of the appliance (2).
•
You can lift and carry the appliance using the carrying handle (6). Never pull or
lift the appliance by the cord.
Changing filters and emptying the dust container
This appliance is not equipped with a dust bag. The dust/dirt is sucked up into
the transparent dust holder instead. Once the dust is in this container, it whirls
around so that it does not block suction. The air sucked in is cleaned by means of
a washable permanent filter in the dust container, a motor protection filter and an
exhaust filter.
We recommend that you clean the filters at least twice a year or as required. We
recommend replacing the filters after 6 to 12 months' use, when they are soiled, or if
the appliance's suction strength is reduced.
IMPORTANT! The appliance must not be used if the filters and the dust container
are not in place.
IMPORTANT! Turn off the appliance and unplug it before changing the filters or
emptying the dust container.
Replacing the Exhaust Filter
•
Remove the exhaust filter cover (a) by grasping the
handle and flipping it up firmly.
•
Remove the filter from the exhaust port and change
it or clean as described in the section on cleaning
below.
•
Replace the exhaust filter in the exhaust port.
•
Fit the cover over the exhaust filter so that the small
pins on the cover engage the upper edge of the
exhaust port. Press the cover into place. You will hear
a 'click' when it locks.
Replacing the Motor Filter
•
Remove the dust container by pressing the lock
button on the handle and removing the container.
•
Press the lock button on the motor filter cover ( c) up
and remove the cover.
•
Grasp the pin at the botton right and remove the filter
element (e) from the appliance.
•
Remove the filter (d) from the filter holder and replace
or clean the filter as described in Cleaning below.
•
Replace the filter in the filter holder.
•
Replace the filter element in the port.
•
Fit the motor filter cover by pushing the upper edge
under the groove and pressing it in until the lock pins
click into place.
•
Replace the dust holder in the appliance.
o Turn the dust container so that the lock button on
the handle faces the appliance.
o Insert the front of the dust container into the slot
on the bottom of the appliance, and press the
handle down until the dust container clicks into
place.
Emptying the dust container and cleaning the permanent filter
It is easy to see when the transparent dust container needs emptying. Empty
the dust container regularly, and never use the appliance when it is full.
•
Remove the dust container by pressing the
lock button on the handle and removing the
container.
•
Take the dust container to a dustbin.
•
Press the release button on the back of the
dust container (see photo). The hinged base
will flip down and the dust will fall out. NB!
Never press the release button unless you are
holding the dust container over a dustbin or
similar waste receptacle.
o Close the dust container again by flipping
the hinged base up and pressing it into
place until the lock pins engage.
•
Take the dust container apart and clean it (refer to the section on cleaning
below).
o Grasp the dust container handle with one hand and support its base with the
other hand. Turn the transparent part (f) until the lock pins disengage and the
"I" marks on the two parts are parallel.
o Remove the handle (i) from the transparent part.
o Pull the inner cylinder (g) on the handle out firmly.
o Screw the inner cylinder (h) loose and remove it.
•
Reassemble the dust container after cleaning.
o Fit the out cylinder on the handle. Next fit the outer cylinder. The parts should
be positioned as indicated on the drawing. Press them firmly into place.
o Insert the handle into the transparent part and turn it until the lock pins
engage and the symbols "I" and "III" on the two parts are parallel.
•
Replace the dust holder in the appliance.
o Turn the dust container so that the lock button on the handle faces the
appliance.
o Insert the front of the dust container into the slot on the bottom of the
appliance, and press the handle down until the dust container clicks into
place.
STORAGE
•
Before putting the appliance away, rewind the cord. Switch off at the socket,
unplug, and press the automatic cord rewind button (5) until the cord is fully
rewound.
o Hold the plug firmly while reeling the cord in to avoid it hitting the appliance
or other nearby objects.
•
Store in a cool dry place. Do not place heavy objects on top of the appliance.
•
The floor nozzle can be parked in the holder on the back of the appliance when
storing horizontally.
CLEANING
•
Clean the appliance by wiping it with a cloth wrung in tepid water. A little
detergent can be added if the appliance is heavily soiled.
•
Do not use scouring pads or any form of strong solvents or abrasive cleaning
agents as they could damage the outside of the appliance.
•
The dust container and the permanent filter can be washed with ordinary soapy
water. Ensure all parts are completely dry before replacing them and using the
apparatus again.
•
Always keep both filters clean (refer to Replacing filters and emptying the dust
container above).
o Shake and beat the filters carefully to remove dust and dirt.
o The filter and the filter element for the motor filter can be washed carefully in
warm water with a little soap if necessary.
o Check it is completely dry before replacing in the appliance. NEVER replace
a filter pad wet.
•
Replace filters with the same type when worn or cannot be cleaned properly.
INFORMATION ON DISPOSAL AND RECYCLING OF THIS PRODUCT
Please note that this Adexi product is marked with this symbol:
This means that this product must not be disposed of together with ordinary
household waste, as electrical and electronic waste must be disposed of separately.
In accordance with the WEEE directive, every member state must ensure correct
collection, recovery, handling and recycling of electrical and electronic waste.
Private households in the EU can take used equipment to special recycling stations
free of charge. In some member states you can, in certain cases, return the used
equipment to the retailer from whom you purchased it, if you are purchasing new
equipment. Contact your retailer, distributor or the municipal authorities for further
information on what you should do with electrical and electronic waste.
GUARANTEE TERMS
The guarantee does not apply:
•
if the above instructions are not followed
•
if the appliance has been interfered with
•
if the appliance has been mishandled, subjected to rough treatment, or has
suffered any other form of damage
•
If faults have arisen because of faults in your electricity supply.
Due to the constant development of our products in terms of function and design,
we reserve the right to make changes to the product without warning.
15
Advertisement
Table of Contents
