Advertisement
7. SIGNALS
Sensor damaged, disconnected or out of temperature range.
[Err,]
[Ctrl][On,,]
Control functions on.
Control functions off.
[Ctrl][OFF,]
Lock functions.
[LOC,][On,,]
Unlocking functions.
[LOC,][OFF,]
[vap,]
Steam.
[nvap]
Invalid conditions for activating the steam.
[prep]
Pre-process in progress.
[StA1]
[StA2]
Start of the process time.
[StA3]
[StA4]
[End1]
[End2]
End of the process time.
[End3]
[End4]
[Tmr1]
[Tmr2]
Remaining time of process.
[Tmr3]
[Tmr4]
8. OPTIONAL ITEMS - Sold Separately
8.1 EasyProg - version 2 or higher
It is an accessory that has as its main function to store the parameters of the controllers. At any time, you
can load new parameters of a controller and unload them on a production line (of the same controller), for
example. It has three types of connections to load or unload the parameters:
- Serial RS-485: It connects via RS-485 network to the controller (only
for controllers that have RS-485).
- USB: it can be connected to the computer via the USB port, using
Sitrad's Recipe Editor.
- Serial TTL: The controller can be connected directly to
EasyProg by the TTL Serial connection.
8.2 Ecase
It is recommended for the Evolution line, keeps water from entering the back part of the instrument. It also
protects the product when the installation site is washed.
8.3 Extension Frame
The Full Gauge Controls extension frame allows the installation of Evolution / Ri line with measures
76x34x77 mm (dimensions of the clipping for fixing in the extension frame is 71x29mm) in varied
situations, since it eliminates precision cut to embed the instrument. Allows customization via a sticker with
the brand and the company contact, and accompany two 10A (250 Vac) switches that can trigger internal
light, air curtain, on / off system or fan.
EASYPROG
8.4 Surge Protective Device (SPD)
Wiring diagram for instalation of SPD in magnectic
contactor
A1
A1 and A2 are the terminals
of the contactor coil.
A2
Wiring diagram for instalation of SPD in line with
loads
For direct drive take in to
LOAD
consideration the specified
maximum current.
ENVIRONMENTAL INFORMATION
Packaging:
The materials used in the packaging of Full Gauge products are 100% recyclable. Try to
perform disposal through specialized recyclers.
Product:
The components used in Full Gauge controllers can be recycled and reused if
disassembled by specialized companies.
Disposal:
Do not incinerate or dispose the controllers that have reached the end of their service as
household garbage. Observe the laws in your area regarding disposal of electronic
waste. If in doubt, please contact Full Gauge Controls.
Products manufactured by Full Gauge Controls, as of May 2005, have a two (02) year
warranty, as of the date of the consigned sale, as stated on the invoice. They are guaranteed
against manufacturing defects that make them unsuitable or inadequate for their intended
use.
The Warranty does not cover expenses incurred for freight and/or insurance when sending
products with signs of defect or faulty functioning to an authorized provider of technical
support services. The following events are not covered either: natural wear and tear of parts;
external damage caused by falls or inadequate packaging of products.
Products will automatically lose its warranty in the following cases:
- The instructions for assembly and use found in the technical description and installation
procedures in Standard IEC60364 are not obeyed;
- The product is submitted to conditions beyond the limits specified in its technical
description;
- The product is violated or repaired by any person not a member of the technical team of
Full Gauge Controls;
- Damage has been caused by a fall, blow and/or impact, infiltration of water, overload
and/or atmospheric discharge.
To make use of the warranty, customers must send the properly packaged product to Full
Gauge Controls together with the invoice or receipt for the corresponding purchase. As much
information as possible in relation to the issue detected must be sent to facilitate analysis,
testing and execution of the service.
These procedures and any maintenance of the product may only be provided by Full
Gauge Controls Technical Support services in the company's headquarters at Rua Júlio de
Castilhos, 250 - CEP 92120-030 - Canoas - Rio Grande do Sul – Brasil
Copyright 2015
RC FILTER
EXCEPTIONS TO WARRANTY
LOSS OF WARRANTY
USE OF WARRANTY
All rights reserved.
Rev. 03
Advertisement
