RCA 54-45 Manual page 11

Connect a 3/4" piece of BARE WIRE from XV1-1 (C) to XV1-3 (S1).
�.
( ) CUT a 5" piece of BLACK COAXIAL CABLE. STRIP off 3/4" of the outer insulation from
both ends so that the braided shield is visible.
tool, UNRAVEL the exposed braids covering the INNER CONDUCTORS. Twist the strands to­
gether, then remove 1/4" of insulation from the CONDUCTORS. CUT OFF
SHIELD from one end and CONNECT the INNER CONDUCTOR of this end to XV1-2( � . ROUTE
the other end to the front of the CHASSIS as shown. It will be connected later.
l , 3 . ( ) Connect a 2-1/2" piece of VIOLET WIRE from XY1-� (S1) to TB4-1 (C).
L;t' .
( ) Connect a 8" piece of THICK WHITE WIRE to XV2-1 (C). ROUTE the other end through
hole "A" to the top of the chassis. It will be connected later.
( ) Cut a 6" piece of BLACK COAXIAL CABLE as described previously. CUT OFF the
BRAIDED SHIELD from one end and CONNECT the INNER CONDUCTOR of this end to XV2-2
(C). ROUTE the other end through the switch cutout to the front of the CHASSIS as shown. It
will be connected later.
I.E(
( ) Connect a 3/4" piece of BARE WIRE from XV2-3 (C) to XV2-8 (C).
V 7. ( ) Connect a 5-1/2" piece of BROWN WIRE from XV2-g (C) through XV2-, 4 (S1)
l/8. ( ) Connect a 3-1/2" piece of BROWN WIRE from XV2-5 (S3) to XV4-12 (C).
l-- · g .
( ) Connect a 2" piece of VIOLET WIRE from XV2-7 (�1) to TB4-l (C).
l).O. ( ) Connect a 4" piece of YELLOW WIRE from XV2-9 (C) to XV4-1 (S2).
v!1· ( ) Connect a 3/4" piece of BARE WIRE from XV4-3 (S1) to XV4-6 (C).
li2. ( ) Connect a 1/2" piece of BARE WIRE from XV4-4 (S1) to lug "X" (S1) on XV4.
U3.
n
( ) Connect
u4.
( ) Connect a 2-1/2" piece of GRAY WIRE from XV4-9
J/
15. ( ) CUT an 8-1/2" piece of BLACK SHIELDED CABLE as described previously. CUT off the
[
16. ( ) Connect a 3" piece of BROWN WIRE from XV4-12 (S
\.
17. ( ) Connect a 2-1/2" piece of VIOLET WIRE from XV6-7 (81) to TB7 -4 (C).
vf8. ( ) Twist a 13" piece of THICK BROWN WIRE and a 13" piece of HEAVY YELLOW WIRE to­
gether. Connecj
(C), to XV5-4
connected later.
lJ.9. ( ) Connect a 3" piece of ORANGE WIRE from TB5-1 (C) to TB6-4 (C).
2-1/2" piece of GREEN WIRE from XV4-5
YELLOW WIRE to XV5-9 (C). Connect the BROWN WIRE through XV5-5
ROUTE the other ends of the twisted pair through HOLE "C". It will be
FIGURE 5
DO
NOT CUT the braid. Using a sharp pointed
l.-·
(r/r)
(dr)
to TB6-2 (C).
� �
10
/
the
to
to TB6-1 (C).
)'.
XV6-3 (s1
XV5-5C.