Page 1 User's Guide CMP0238-00 EN...
Page 2 (excluding the U.S.) failure to strictly comply with Seiko Epson Corporation's operating and maintenance instructions. Seiko Epson Corporation shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those designated as Original Epson Products or Epson Approved Products by Seiko Epson Corporation.
Page 3: Table Of Contents
Exiting procedure..... . . 45 Using Epson Edge Print..... 46 Maintenance Configuration of main screen.
Page 4 Checking for clogged nozzles....135 Epson Edge Print..... . 205 Print Head Cleaning.
Page 5: Meaning Of Symbols
The video manuals have been uploaded to YouTube. Illustrations Click [Epson Video Manuals (video)] on the top page of the Online Manual, or click the following blue text to view the manuals. The product illustrations and screenshots in this manual may differ slightly from the real things.
Page 6: Viewing Pdf Manuals
SC-F10000 Series User's Guide Notes on Manuals Click the title to open the relevant page. If the subtitles are not displayed when you play the video, click the subtitles icon shown in the image below. Click [+] to open the titles lower in the hierarchy.
Page 7: Introduction
SC-F10000 Series User's Guide Introduction Introduction Printer Parts Front Section Front cover Open when loading media, cleaning the inside of the printer, or removing jammed media. This is normally closed and locked when using the printer. Maintenance cover (left) Open this cover to clean the area around the caps. This is normally closed when using the printer.
Page 8 SC-F10000 Series User's Guide Introduction Ink supply unit Supplies the printer with ink from the ink cartridges. Two ink cartridges for each color can be inserted. Handle After placing the roll core on the left media holder, rotate the handle and press the media holder into the roll core.
Page 9: Ink Supply Unit
SC-F10000 Series User's Guide Introduction Signal lamps Lamps light or flash in 3 colors to notify you of the status of the printer. Basically, the meaning of the lamps' colors are as follows. The color of the lamps, in order from top to bottom, are red, yellow, and green.
Page 10 SC-F10000 Series User's Guide Introduction Ink cartridges Two ink cartridges for each color are inserted. Normally, one ink cartridge continues to be used. Once the ink cartridge is expended, the printer automatically switches to the other ink cartridge. As a result, even if ink is expended during printing, the ink cartridge can be replaced without interrupting printing.
Page 11 SC-F10000 Series User's Guide Introduction Casters Attached to the four legs. Always lock these when using the printer. Ink supply unit wire Use with the wire as connected. If you move the ink supply unit while connected to the printer, without connecting them with the wire, the ink supply tube may be damaged.
Page 12: Right View
SC-F10000 Series User's Guide Introduction Right view Lock release levers Releases the maintenance cover's locks. The same parts are on both the left and the right sides. When opening the maintenance cover, open it while lowering the levers. The maintenance cover will automatically lock when shut.
Page 13 SC-F10000 Series User's Guide Introduction Levelers When installing, check the level gauge, use the levelers to adjust the printer to be level, and then fix the printer in place. Install metallic plates on the bottom to distribute the load. Keep the printer level after moving it.
Page 14: Inside
SC-F10000 Series User's Guide Introduction Inside When the following parts become dirty, they may cause problems with the print results. Regularly clean or exchange these parts as described in the chapters listed in the reference sections below or by following the messages on the screen.
Page 15 SC-F10000 Series User's Guide Introduction Media edge plates The media edge plates prevent the media riding up and keeps fibers on the cut edge of the media from touching the print head. Position the plates at either side of the media before printing.
Page 16: Back
SC-F10000 Series User's Guide Introduction Back Media loading lever After loading media, lower the media loading lever to keep the media in place. Raise the lever to release the media prior to removal. Because this media loading lever has the same function as the media loading lever on the front of the printer, you can operate whichever is the easiest to use in your situation.
Page 17 SC-F10000 Series User's Guide Introduction Media holder Place media on these holders. The same parts are on both the left and the right sides. Roll support Rest media on these supports before placing it on the media holders. The same parts are on both the left and the right sides.
Page 18: Control Panel
SC-F10000 Series User's Guide Introduction Status lamp The color indicates the network's communication speed. Green : 1000Base-T USB port Connects the USB cable. Control panel P light (power light) The printer's operational status is indicated by a lit or flashing light.
Page 19 SC-F10000 Series User's Guide Introduction button: Rewinds the media. button: Feeds the media. When the button is used to rewind, the media will stop when its edge reaches the print start position. Rewind can be resumed by releasing the button and then pressing it again.
Page 20: Understanding And Operating The Display
SC-F10000 Series User's Guide Introduction Understanding and Operating the Display This chapter describes how to understand and operate the screen layout, using the Home screen, Menu screen, and the display for operating procedures screen as an example. Home screen On the Home screen, you can switch between the Status Display screen and the Media Settings screen by pressing the display switching button.
Page 21 SC-F10000 Series User's Guide Introduction Internal lamp Switches the internal lamp on or off. The display changes as follows, depending on the status. Setting Auto for Inside Light in the Printer Settings, turns the light on automatically when operations that need light are done, such as while printing, and turns it off when the operation is complete.
Page 22 SC-F10000 Series User's Guide Introduction During printing, the display switches, as seen in the illustration, and shows the following information and buttons. (1) File name and preview of image being printed (2) The Printed Length of media, Remaining Print Length of media, throughput (print length per hour), throughput (print area per hour), or Time until media replacement Pressing the display area while printing displays the screen to set the display details for (2).
Page 23 SC-F10000 Series User's Guide Introduction Information regarding consumables, such as ink cartridges, are displayed using the following icons and bar lengths. Ink cartridge status Displays the approximate level of remaining ink and the current status. If the amount of ink runs low, the bar becomes shorter.
Page 24 SC-F10000 Series User's Guide Introduction The wiper roll will need to be replaced soon. A new wiper roll needs to be prepared. Pressing the display area shows the Supply Status screen and you can check the part numbers for consumables. You can also switch the ink cartridges to be used.
Page 25 SC-F10000 Series User's Guide Introduction * Maintenance Cleaning is head cleaning that the printer automatically does, after a set period of time has passed, to keep the print heads in good condition. Set Maintenance Cleaning from the Maintenance Setting menu.
Page 26 SC-F10000 Series User's Guide Introduction (4) Strength of the Fan mode The Fan mode is enabled when the heater is Off. Pressing allows you to change the fan's strength. Media Feed Adjustment information during printing If you do Media Feed Adjustment while printing, the adjusted values appear. Pressing the display area shows the Settings screen.
Page 27: Menu Screen
SC-F10000 Series User's Guide Introduction If, in contrast, the feed amount is too large, white bands (pale stripes) will appear; adjust the feed amount downwards. Note: When the settings screen for Media Feed Adjustment is displayed, you can change the values by pressing the buttons on the left side of the screen.
Page 28: Instructions Screen
SC-F10000 Series User's Guide Introduction Appears when all of the buttons, etc., do not fit in the operation area. If the scroll bar is shown, check the buttons, etc., by scrolling up and down. You can scroll by pressing and holding the item you want to scroll and moving it up and down (slide), or by pressing to scroll, as shown in the illustrations below.
Page 29: Types Of Buttons
SC-F10000 Series User's Guide Introduction Step number Displays the total number of steps. The color of the step that is currently shown changes to blue. Types of Buttons Depending on the screen, the following types of buttons appear. Even if they are the same buttons, how they look may change, depending on the situation.
Page 30 SC-F10000 Series User's Guide Introduction This indicates that the button cannot be used. These buttons turn gray only when they cannot be operated for reasons, such as items not being selectable because of unmet conditions. The conditions for being operable change depending on the button.
Page 31: Notes On Usage And Storage
SC-F10000 Series User's Guide Introduction ❏ Maintenance such as cleaning and replacement Notes on Usage and must be performed according to usage frequency or at recommended intervals. Failure to perform Storage regular maintenance could result in loss of print quality. In the absence of the appropriate...
Page 32: Notes On Handling Ink Cartridges
❏ Six months after opening the package of ink Contact your dealer or Epson Support. cartridge ❏ If you have not used the printer for a long time, ❏ If you move ink cartridges from a cold place to a check the print heads for clogging before you start printing.
Page 33: Handling Media
SC-F10000 Series User's Guide Introduction ❏ Removed ink cartridges may have ink around the ❏ When not in use, media should be removed from ink supply port, so be careful not to get any ink on the printer, rewound, and inserted in its original the surrounding area when removing the packaging for storage.
Page 34: Introducing The Supplied Software
Note: Printer drivers are not provided. A software RIP is required for printing. The Epson Software RIP, "Epson Edge Print", is included with this printer on a separate CD. The Epson Web site provides plug-ins for the printer.
Page 35 This is useful as it allows you to enter addresses and names using the keyboard. LFP Accounting Tool The LFP Accounting Tool is not installed automatically. Download it from Epson's website and install it, if necessary. This is software that can calculate costs for printed material printed by this printer (cost of paper, cost of ink, etc.) and can display, total, and output information (in CSV format) about print jobs.
Page 36: Using Epson Edge Dashboard
Linux machines. Register your printer manually from the Printer Registration screen. This screen is displayed The application can be launched using the upon starting up Epson Edge Dashboard for the first following methods. time. For details, see the help for Epson Edge Windows Dashboard.
Page 37: Checking And Managing The Printer's Status
SC-F10000 Series User's Guide Introduction Checking and Managing the Printer's Status Follow the next steps on the Printer Operation screen to check and manage the printer's status. The Printer Operation screen provides a view of the same status information as the printer's control panel screen. It also allows you to perform standard maintenance operations.
Page 38 EPSON Manuals Button Click to view your printer’s "Online Manual". *1 This button is not displayed when accessing and using Epson Edge Dashboard on another computer on the network. For details, see the help for Epson Edge Dashboard. *2 This button is not displayed when using this software on a Linux machine.
Page 39: Downloading And Copying Media Settings Of Emx File
Configuring optimum print settings for the media you use can require pain, time, and efforts. You can use print setting file (EMX file) provided by Epson, which provides optimum print quality settings for the commercially available media being used. (The provided files differ according to the country and region in which you live.)
Page 40 However, you cannot reset the changed items after you click the Apply button. Write to File Button Click to collect the media settings displayed in the current list and save them to a single file on your computer. For details, see the help for Epson Edge Dashboard.
Page 41 Check Registered Media Click to save the list of information for all the media settings currently registered to the Settings Button printer selected in the list of registered printers. For details, see the help for Epson Edge Dashboard. Target Media Settings List...
Page 42 Check the checkbox on the left of You can download only the EMX files corresponding to Media Vendor to select all EMX files displayed the printers you registered on the Epson Edge on the current page. Dashboard. In addition, regardless of the printers...
Page 43 SC-F10000 Series User's Guide Introduction From the source media settings list, select the Important: media settings that you want to add to or change on the printer. If media setting values already registered to the printer are overwritten by an EMX file for...
Page 44: Editing Media Settings
For media settings media settings list, no matter where they have been copied from EMX files, the media name is copied. When you are using Epson Edge Dashboard on entered in the field. a computer that cannot download EMX files, you can You can change a setting’s Media Type only...
Page 45: Exiting Procedure
SC-F10000 Series User's Guide Introduction Exiting procedure Close the Web browser.
Page 46: Using Epson Edge Print
SC-F10000 Series User's Guide Introduction Using Epson Edge Print Configuration of main screen The main screen appears when you start Epson Edge Print. The configuration and functions of the main screen are shown below. Names of parts Functions Menu bar You can do settings and operations in the various menus.
Page 47 (Basic Settings) - Media Size in the Job Settings menu. The distance from the left and right edges of the media to the dotted lines are the margins. You can change the margins in Manage Preset in the Tool menu. For details, see the help for Epson Edge Print.
Page 48 Job List (D). The icons on the right are the Job Setting menu. The content of the setting area changes depending on the items that are selected. For details, see the help for Epson Edge Print. Clicking the in the top right of the setting area closes the setting area so the preview area is enlarged by that amount.
Page 49: Printing Procedure
❏ Epson Edge Print is running. Click (Basic Settings) in the Job Setting ❏ The printer is registered to Epson Edge Print. menu. The setting area changes to Basic Settings, and ❏ The media is loaded on the printer and it is ready to you can set the media size, media name (print print.
Page 50: Using Media Efficiently Without Waste (Nested Printing)
For details about the functions, see the help for Epson using Media Management. Furthermore, do Edge Print. not select the media setting [00 RIP Settings]...
Page 51 SC-F10000 Series User's Guide Introduction ❏ Selecting multiple individual jobs for nesting All the selected jobs appear in the preview area. In the Job List, appears on the left side of the name of the job. ❏ Setting multiple copies with...
Page 52 SC-F10000 Series User's Guide Introduction Confirm that there is sufficient charge remaining Select the root to the nested job (the line in which in the chip unit. is displayed to the left of the job name) in Job List and click (UnNest) in the job toolbar.
Page 53: Printing Repeating Pattern (Step And Repeat)
SC-F10000 Series User's Guide Introduction Example: Shifted 1/2 vertically Printing repeating pattern (Step and Repeat) You can create and print repeating patterns by placing 1 image and shifting it vertically and horizontally. The procedure for setting up a pattern is explained below.
Page 54 SC-F10000 Series User's Guide Introduction If gaps occur between images you You can set from which position of the image the pattern starts. printed You can drag the pattern in the preview area and You can set Overlapping Amount and do adjustments...
Page 55 With step and repeat processes on the printer, once printing is started, Epson Edge Print and the RIP server can be shut down while printing. However, it is not possible to shift and position the image, nor to specify the starting point of the pattern.
Page 56: Using Lfp Accounting Tool
SC-F10000 Series User's Guide Introduction Double-click the LFP Accounting Tool shortcut Using LFP Accounting icon on the desktop. Tool Basic Settings You must perform the basic settings in advance for the LFP Accounting Tool to obtain job information from the printer for the calculation of costs and so on.
Page 57 SC-F10000 Series User's Guide Introduction When you click OK, this software starts Click the Ink Unit Price tab, and then select the acquiring job information from the selected printer. printers. Set the unit prices Set the unit prices for the paper and ink being used by the printer.
Page 58 SC-F10000 Series User's Guide Introduction Make settings for all of the Information on To hide canceled jobs, clear Show canceled or Other Costs items, and then click Register. aborted jobs. You can register up to five additional costs for each job information, such as administration costs, utility costs, or lamination costs.
Page 59 SC-F10000 Series User's Guide Introduction Select Starting Month or Starting Day on the Job Information List screen. Click Search to display jobs that satisfy the search conditions. Click Export to CSV to export the summarized jobs to a CSV file. For details, see the LFP Accounting Tool help.
Page 60: Screen Layout
❏ Double-click this software's icon on the task tray ❏ Right-click this software's icon on the task tray, and then click Job Information ❏ On Epson Edge Dashboard, click the LFP Accounting Tool on the Accounting tab of the Printer Operation screen For details of other screens, see the LFP Accounting Tool help.
Page 61 SC-F10000 Series User's Guide Introduction Item Explanation Starting Day This is available when Year, Half Year, or Quarter is selected from Period. Select from 1 to 31 as the day to start summarizing. Jobs to display Set the maximum number of jobs displayed in list view. You can select from "50", "100", or "200".
Page 62 SC-F10000 Series User's Guide Introduction Item Explanation Set the period for the data to be output to a CSV file. Selected Period/All When you want to output data selected from Period that is displayed in the current list Periods view, set Selected Period.
Page 63: Using Epson Software Updater
Do not turn off the computer or printer while IPv6: https://[2001:db8::1000:1]/ updating. Exiting procedure Note: Software that is not displayed in the list cannot be Close the Web browser. updated using EPSON Software Updater. Check for the latest versions of the software from the Epson Web site. http://www.epson.com...
Page 64: Uninstalling Software
❏ Exit any other applications that may be running. This section describes how to uninstall Epson communications drivers. For uninstallation of other software, see the software help. Turn off the printer, and unplug the interface cable.
Page 65: Basic Operations
1. Register media settings values. (when using the EMX file with the new media) You can easily register media settings values to the printer using Epson Edge Dashboard. If you are registering with Epson Edge Dashboard, download the EMX file 6. Print.
Page 66: Notes On Loading Media
SC-F10000 Series User's Guide Basic Operations Load the media just before printing. The pressure rollers may crease media left in the printer. The media may also become wavy or curled, causing jams or resulting in the media coming into contact with the print head.
Page 67: Loading Media
SC-F10000 Series User's Guide Basic Operations While holding the tabs of the media edge plate on both sides, move the plate out of the way toward both edges of the platen. Raise the media loading lever. Loading media You can check the procedure in a video on YouTube.
Page 68 SC-F10000 Series User's Guide Basic Operations Place the media on the roll support. Have the roll Important: support moved inward for about 20 cm from the roll end. If the right holder handle shaft is not visible, rotate the handle forward until it stops. The media can not be properly loaded if the handle shaft is not visible.
Page 69 SC-F10000 Series User's Guide Basic Operations While lifting the right lift lever, firmly insert the While pressing from the top of the media holder, media holder onto the roll core of the media. tighten the fixing screw until it no longer turns.
Page 70 SC-F10000 Series User's Guide Basic Operations Insert the media approximately 20 cm into the Note: opening, then lower the media loading lever. You can change the media suction on the platen through the screen operation. Increasing the media The media that you inserted is clamped and does suction lowers the possibility of media falling down.
Page 71 SC-F10000 Series User's Guide Basic Operations c. Hold the center of the media in one hand, and For each step given below, be sure to slacken the pull out the media until its edge reaches the media before pulling it out. The media may get media holder.
Page 72 SC-F10000 Series User's Guide Basic Operations “Using the Auto Take-up Reel Unit” on Move to the front side, and while holding the tabs page 74 of the media edge plate on both sides, move the plate to the top edge of the media.
Page 73 SC-F10000 Series User's Guide Basic Operations Close the front cover, and then move the left and right lock levers inward. Set the media information on the screen, and press OK. Do the following settings here. ❏ Media: Set the media to use for printing ❏...
Page 74: Using The Auto Take-Up Reel Unit
SC-F10000 Series User's Guide Basic Operations Using the Auto Take-up Important points for correct take-up Reel Unit Observe the following points for correct take-up of The Auto Take-up Reel Unit automatically takes up media. media as it is printed, improving the efficiency of ❏...
Page 75: Attaching The Roll Core
SC-F10000 Series User's Guide Basic Operations Attaching the Roll Core Important: Always press the media feed switch to feed the What You’ll Need media. If the media is pulled by hand, the media may twist during take-up. ❏ Take-up roll core that is the same width as the...
Page 76 SC-F10000 Series User's Guide Basic Operations Align and move the right-side media holder to Check that the left-side media holder is fully the right edge of the media. inserted into the roll core and that the roll core and edges of the media are not misaligned.
Page 77 SC-F10000 Series User's Guide Basic Operations While pressing from the top of the media holder, Leave a 10 to 20 cm wide section in the center of tighten the fixing screw. the media, and cut at least 25 cm in height from the left and right corners of the media.
Page 78: Take-Up With The Normal Feeding Procedure
SC-F10000 Series User's Guide Basic Operations Flip the Auto switch to Take-up with the Normal Feeding Procedure Printed side in While pulling the center of the media straight down, wrap it around the roll core from back to front, and affix it using commercially available adhesive tape.
Page 79 SC-F10000 Series User's Guide Basic Operations Printed side out Flip the Auto switch to While pulling the center section of the media straight down, affix the media to the take up roll core with commercially available adhesive tape. Confirm that the media is attached without looseness.
Page 80: Take-Up With The Take-Up Feeding Procedure
SC-F10000 Series User's Guide Basic Operations Repeat the following procedure and take-up the Take-up with the Take-Up media for a double wrap around the roll core. Feeding Procedure a. Hold the button pressed to slightly slacken the media at the back side.
Page 81 SC-F10000 Series User's Guide Basic Operations Flip the Auto switch to Note: You can confirm differences in tension by lightly tapping both edges of the media as shown in the illustration below. Lower the media loading lever. Confirm that the media is attached without Move to the front side, and while holding the tabs looseness on the front and back sides.
Page 82 SC-F10000 Series User's Guide Basic Operations Printed side out Close the front cover, and then move the left and right lock levers inward. Move the lock lever on the left and right side outwards to open the front cover. Set the media information on the screen, and press OK.
Page 83 SC-F10000 Series User's Guide Basic Operations Repeat the following procedure and take-up the Flip the Auto switch to media for a double wrap around the roll core. a. Hold the button pressed to slightly slacken the media at the back side.
Page 84 SC-F10000 Series User's Guide Basic Operations Close the front cover, and then move the left and Note: right lock levers inward. You can confirm differences in tension by lightly tapping both edges of the media as shown in the illustration below.
Page 85: Removing The Take-Up Roll
SC-F10000 Series User's Guide Basic Operations Removing the Take-up Cutting Media Roll Caution: ❏ The dryer may be hot; observe all necessary Follow the steps below when replacing the media. precautions. Failure to observe the necessary precautions could result in burns.
Page 86: Removing Media
SC-F10000 Series User's Guide Basic Operations When information, such as the remaining Rotate the left media holder handle to the far side amount of media, is printed, a line is printed at until it stops. the cut position. Print Information is printed on...
Page 87: Removing The Loaded Media
SC-F10000 Series User's Guide Basic Operations Loosen the right media holder fixing screw and While holding the tabs of the media edge plate on remove the media holder. both sides, move the plate out of the way toward both edges of the platen.
Page 88 SC-F10000 Series User's Guide Basic Operations Rotate the right media holder handle to the near To prevent the media from dropping, lift up the side until it stops. left lift lever to support media. The part A on the illustration and the shaft of the handle will be visible.
Page 89: When The Remaining Media Runs Out
SC-F10000 Series User's Guide Basic Operations Close the front cover, and then move the left and Move to the back side and check the condition of right lock levers inward. the media. If the media is affixed to the roll core, then cut it apart using scissors as seen in the illustration, and move on to the next procedure.
Page 90: Before Printing
SC-F10000 Series User's Guide Basic Operations Lower the media loading lever. Print Adjustments Use this menu in the following cases. Using new media not registered to the printer Perform Automatic Adjustment after loading media to the printer. When banding or graininess is found in the print...
Page 91: Print Head Alignment
SC-F10000 Series User's Guide Basic Operations Adjustment Procedure Print Head Alignment Check that the printer is ready, and load the media according to the actual usage conditions. Auto When using the Auto Take-up Reel Unit, attach The same adjustment as Print Head Alignment of the media to the roll core.
Page 92: Media Feed Adjustment
SC-F10000 Series User's Guide Basic Operations 600x600dpi -2.5 pass : Approx. 250 mm The screen for entering confirmation results for the adjustment pattern is displayed. 600x600dpi -3.1 pass : Approx. 200 mm On the entry screen of each block, set the number...
Page 93 SC-F10000 Series User's Guide Basic Operations ❏ When Auto and Manual(Standard) adjustments If there are patterns where the overlapping or have failed gaps are the same, enter the middle value in Step ❏ When banding can be seen in the print results even Enter “-0.15%”...
Page 94 SC-F10000 Series User's Guide Basic Operations When adjustments are complete, the Home screen is displayed.
Page 95: Printable Area
SC-F10000 Series User's Guide Basic Operations Printable area Left and Right Edge Positions of Media The left and right edges of media recognized by the printer vary, as shown below, according to the Width Detection settings. Width Detection On : The printer automatically detects the left and right edges of the loaded media.
Page 96: Printable Area And Image Print Area
SC-F10000 Series User's Guide Basic Operations Printable Area and Image Print Area ❏ When not using the Information Printing function As shown in the illustration, the printable area can be used as an image print area for all jobs.
Page 97 SC-F10000 Series User's Guide Basic Operations ❏ When using the Information Printing function As shown in the illustration, the size of the left and right sides of the image print area is reduced by the amount of information to print.
Page 98 SC-F10000 Series User's Guide Basic Operations The details of are shown below. Position Explanation Available Setting Range *1, *3 Half the value selected for Margin Between Pages in the printer's setup 5 to 499.5 mm Trailing edge menu. To maintain media feeding accuracy, if the settings are less than 10 mm, the settings are switched to 5 mm.
Page 99 SC-F10000 Series User's Guide Basic Operations Note: If the following points are not observed when Width Detection is Off, printing may occur outside the left and right edges of the media. Ink used outside the edges of the media will stain the inside of the printer.
Page 100: Maintenance
SC-F10000 Series User's Guide Maintenance Maintenance When to Perform Various Maintenance Operations Cleaning and replacement of consumables must be performed to ensure the print quality of the printer. Failure to perform appropriate maintenance could result in reduced print quality. Read the following to perform appropriate maintenance.
Page 101 SC-F10000 Series User's Guide Maintenance When to perform Component to be cleaned When a cleaning message is displayed on Anti-drying caps the control panel “Cleaning anti-drying caps” on page 110 You can check the procedure in a video on YouTube.
Page 102: Replacing Consumables
SC-F10000 Series User's Guide Maintenance Replacing Consumables When to perform Component to be replaced When ink low warning is displayed on the Ink cartridge control panel display “Replacement procedure” on page 117 When a prepare and replacement Waste Ink Bottle message is displayed on the control panel “Disposing of Waste Ink”...
Page 103 SC-F10000 Series User's Guide Maintenance When to perform Operation When a clog is found after checking for Cleaning the print head clogged nozzles “Print Head Cleaning” on page 136 Once a month Checking the circuit breaker’s performance “Checking the circuit breaker’s performance” on page 137...
Page 104: What You'll Need
SC-F10000 Series User's Guide Maintenance Media Cleaner Brush (supplied with the printer) What You’ll Need Use when cleaning with media cleaner. Ready the following items before beginning cleaning and replacement. When the supplied parts have been completely used, purchase new consumables.
Page 105: Cleaning
SC-F10000 Series User's Guide Maintenance ❏ Touch a metallic object before starting work to Caution: discharge any static electricity. ❏ Store ink cartridge, cleaning fluid, and waste ink in a location out of the reach of children. Cleaning ❏ During maintenance, wear protective clothing, including protective eyewear, gloves, and a mask.
Page 106 SC-F10000 Series User's Guide Maintenance Soak a soft cloth in water, wring it out Soak a soft cloth in water, wring it out thoroughly, and then wipe off any ink, lint, or thoroughly, and then wipe off any ink, lint, or dust that has adhered to the platen.
Page 107 SC-F10000 Series User's Guide Maintenance Open the left-side maintenance cover while Soak a soft cloth in diluted neutral detergent, lowering the lock release levers. wring it out thoroughly, and then wipe off any glue or ink that has adhered to the front and back of the media edge plates.
Page 108: Using Cleaning Liquid
SC-F10000 Series User's Guide Maintenance (2) Hook into the rear of tab: Front corner of the After wiping off stains, insert the media edge platen plate from the left side of the platen. Insert the right media edge plate also from the left side.
Page 109: Cleaning The Media Cleaners
SC-F10000 Series User's Guide Maintenance Put the cup supplied with the Cleaning Kit on the Check the on-screen message, and then move to tray, and pour approximately 10 ml of Cleaning the back side and remove the media cleaners. liquid into the cup.
Page 110: Cleaning Anti-Drying Caps
SC-F10000 Series User's Guide Maintenance When you finish cleaning a media cleaner, install Important: it to the printer. When using a cleaning stick to wipe off a cap, do not Hold the tabs as you insert the media cleaner wipe off the area around the hole inside the cap. The until you hear a click.
Page 111 SC-F10000 Series User's Guide Maintenance When there is lint or dust on the cap Lower the lock release lever to open the left-side maintenance cover. Remove it by using the tip of the cleaning stick. Dampen the cleaning stick with cleaning fluid.
Page 112 SC-F10000 Series User's Guide Maintenance Hold the cleaning stick in a perpendicular Use a new dry cleaning stick to wipe up all the ink orientation, and wipe the inside of the cap. and cleaning fluid on the inside, edges, and area around the cap.
Page 113: Cleaning Suction Caps
SC-F10000 Series User's Guide Maintenance Wipe up all the ink and cleaning fluid, leaving no Lower the lock release lever to open the right-side residue, as shown in the illustration below. If any maintenance cover. ink or cleaning fluid is left over, it could clog the nozzles.
Page 114: Cleaning Around The Print Head
SC-F10000 Series User's Guide Maintenance Close the maintenance cover. Confirm that the print head has moved to the right side, and then press the lock release lever to open the right-side maintenance cover. On the control panel screen, press Done.
Page 115: Cleaning The Inside Light
SC-F10000 Series User's Guide Maintenance Wipe off any ink, lint, or dust that is stuck to the Close the maintenance cover. area shown in the illustration. On the control panel screen, press Done. Cleaning the inside light The printer has an inside light inside the front cover and maintenance covers to make it easy to check print results and areas for maintenance.
Page 116: Cleaning The Front Cover
SC-F10000 Series User's Guide Maintenance Soak a soft cloth in water, wring it out Soak a soft cloth in water, wring it out thoroughly, and then wipe any dirt off of the thoroughly, and then wipe any dirt off of the inside light surfaces shown in the illustration.
Page 117: Replacing Consumables
Replacement procedure Important: ❏ Epson recommends the use of genuine Epson Wipe the inner side of the window. ink cartridges. Epson cannot guarantee the quality or reliability of non-genuine ink. The...
Page 118 SC-F10000 Series User's Guide Maintenance Opening and shaking Important: Place a new ink cartridge on a flat surface with the Do not use a cutter to cut along the dashed ink supply outlet slot facing up. lines. Failure to observe this precaution could damage the internal parts and cause ink to leak.
Page 119 SC-F10000 Series User's Guide Maintenance Take out the ink supply outlet from inside and fix it as shown in the illustration. Remove tape from the surface of ink supply outlet. Place the ink cartridge with the ink supply outlet facing the side, and slide the ink cartridge back and forth longitudinally within the range of approximately 10 cm for ten times.
Page 120 SC-F10000 Series User's Guide Maintenance ❏ When using 3 L ink cartridge Turn over the ink cartridge and repeat the same cycle for ten times. Move the ink cartridge at a rate of one back-and-forth cycle per second. ❏ When using 10 L ink cartridge...
Page 121 SC-F10000 Series User's Guide Maintenance While pressing the levers on both sides of the Remove the used ink cartridge from the ink connector, pull the connector toward you to supply unit. remove it, and place the connector on the rear surface of the ink cartridge cover.
Page 122 SC-F10000 Series User's Guide Maintenance ❏ When using 3 L ink cartridge Install the connector to the ink supply outlet. Insert the connector until you hear a click.
Page 123: Replace The Wiper Roll
SC-F10000 Series User's Guide Maintenance “Precautions regarding maintenance” on Raise the ink cartridge cover. page 104 Replacement procedure Check the on-screen message, and then press Start. Lower the lock release lever to open the right-side maintenance cover. Repeat the opening, shaking and replacement procedures to replace other ink cartridges.
Page 124 SC-F10000 Series User's Guide Maintenance Open the left and right covers outwards. Install a new wiper roll. Insert the shaft into the groove on the wiper unit, and press inward until you hear a click. Hold the shaft and roll and pull them out, and remove the wiper roll.
Page 125: Disposing Of Waste Ink
SC-F10000 Series User's Guide Maintenance Maintenance menu U “Maintenance menu” on Install the wiper unit at an angle from above the page 165 printer, and then press the lock lever. Waste Ink Counter U “Waste Ink Counter” on page 125...
Page 126: Replacing The Media Holder
SC-F10000 Series User's Guide Maintenance Remove the waste ink bottle from the holder. Insert the waste ink tube into the mouth of the new waste ink bottle and place it in the holder. Remove the waste ink bottle sideways, without tipping it, as shown in the illustration.
Page 127 SC-F10000 Series User's Guide Maintenance Replace the media holders that have switches, for Remove the cables from the clamps. feeding and the media holders for take-up. Make sure you use a replacement media holder for this printer. “Options and Consumable Products” on...
Page 128 SC-F10000 Series User's Guide Maintenance Use the hex wrench to loosen the head of the Insert the new media holder from the outer side. screw so it rises up about 5 mm as shown in the illustration. Insert the parts you pulled out in Step 6.
Page 129 SC-F10000 Series User's Guide Maintenance “Removing the Take-up Roll” on page 85 Connect the 2 cables to the printer. Remove the cables from the clamps. Pass the cables through the clamps. Remove the 2 cables from the printer. On the screen, press Done.
Page 130 SC-F10000 Series User's Guide Maintenance Loosen the fixing screw on the media holder. Attach the end cover and use a Phillips screwdriver to tighten the screw. Use a Phillips screwdriver to remove the screw shown in the illustration, and then remove the end cover.
Page 131: Other Maintenance
SC-F10000 Series User's Guide Maintenance Pass the cables through the clamps. Make sure the printer is on, and then lower the ink cartridge cover of the ink cartridge to be shaken, toward you. The ink cartridge with a flashing left (blue) lamp is the one that needs to be shaken.
Page 132 SC-F10000 Series User's Guide Maintenance While pressing the levers on both sides of the Remove the ink cartridge from the ink supply connector, pull the connector toward you to unit, and place it on a flat surface with the ink remove it, and place the connector on the rear supply outlet facing the side.
Page 133 SC-F10000 Series User's Guide Maintenance ❏ When using 10 L ink cartridge ❏ When using 10 L ink cartridge ❏ When using 3 L ink cartridge Turn over the ink cartridge and repeat the same ❏ When using 3 L ink cartridge cycle for three times.
Page 134 SC-F10000 Series User's Guide Maintenance Place the shaken ink cartridge such that the ink Install the connector to the ink supply outlet. supply hole faces the connector. Insert the connector until you hear a click. ❏ When using 10 L ink cartridge...
Page 135: Checking For Clogged Nozzles
SC-F10000 Series User's Guide Maintenance Set Nozzle Check between Pages. Raise the ink cartridge cover. A check pattern is printed according to the Execution Timing that is set. You can visually inspect the check pattern to determine whether there may be faint or missing colors in the preceding or following printout.
Page 136: Print Head Cleaning
SC-F10000 Series User's Guide Maintenance When Saving Mode is On Perform head cleaning as necessary. ❏ If the width is equal to or greater than 26 inches Perform head cleaning if there are faint or missing parts of the check pattern that was printed.
Page 137: Checking The Circuit Breaker's Performance
SC-F10000 Series User's Guide Maintenance Checking the circuit breaker’s Execute Print Head Refresh if there are multiple large performance clogs, even though you executed Cleaning(Heavy). When you execute Print Head Refresh, the suction caps need to be cleaned, because of this, the cleaning...
Page 138 ON. breaker switch once and turn it back ON. Repeat Steps 2 to 5 to check the performance of the other circuit breaker. If any abnormality is found, contact your local dealer or Epson service call center.
Page 139: Disposal Of Used Consumables
Dispose of items according to local laws and regulations. For example, contract a industrial waste disposal company for disposal. In such cases, submit the “Safety data sheet” to the industrial waste disposal company. You can download it at your local Epson Web site.
Page 140: Control Panel Menu
SC-F10000 Series User's Guide Control Panel Menu Control Panel Menu Menu List The following items and parameters can be set and executed in the Menu. See the reference pages for more details on each item. General Settings For more information on these items, see U “General Settings menu”...
Page 141 SC-F10000 Series User's Guide Control Panel Menu Item Parameter LCD Brightness 1 to 9 Sound Button Press 0 to 3 Alert 0 to 3 Completion Notice 0 to 3 Warning Notice Volume 0 to 3 Repeat Never, Until Stopped Error Tone...
Page 142 SC-F10000 Series User's Guide Control Panel Menu Item Parameter Margins Side(Right) 3 to 25 mm Side(Left) 3 to 25 mm Margin Between Pages 0 to 999 mm Width Adjustment -10 to +10 mm Print Start Position 0 to 1000 mm...
Page 143 SC-F10000 Series User's Guide Control Panel Menu Item Parameter Actions after Media Scuffing Stop Immediately, Stop when Continuously Detected, Ignore Nozzle Check between Pages Execution Timing Print Length 1 to 9999 meters Print Page Each 1 to 9999 pages Print Duration...
Page 144 SC-F10000 Series User's Guide Control Panel Menu Item Parameter Network Settings Network Status Wired LAN Status, Email Server Status, Print Status Sheet Advanced Device Name TCP/IP Proxy Server Email Server Server Settings, Connection Check IPv6 Address Enable, Disable Link Speed & Duplex...
Page 145 SC-F10000 Series User's Guide Control Panel Menu Item Parameter 01 XXXXXXXXXX to 50 XXXXXXXXXX Change Name Media Type Ultra-Thin, Thin, Med-Thick, Thick Pass Mode 300x600dpi -1.1pass, 300x600dpi -1.5pass, 300x600dpi -2.1pass, 300x600dpi -3.1pass, 600x600dpi -2.1pass, 600x600dpi -2.5pass, 600x600dpi -3.1pass, 600x600dpi -4.3pass, 600x1200dpi -5.0pass, 600x1200dpi -5.0pass HD, 1200x1200dpi -9.0pass HD...
Page 146 SC-F10000 Series User's Guide Control Panel Menu Item Parameter Drying Time 300x600dpi -1.1pass 0 to 200 sec 300x600dpi -1.5pass 0 to 200 sec 300x600dpi -2.1pass 0 to 200 sec 300x600dpi -3.1pass 0 to 200 sec 600x600dpi -2.1pass 0 to 200 sec 600x600dpi -2.5pass...
Page 147 SC-F10000 Series User's Guide Control Panel Menu Item Parameter Feeding Tension Lv1 to Lv4 Paper Suction Lv0 to Lv10 Media Feed Speed Limitation On, Off Pressure Roller Load Light, Standard Remove Skew On, Off Stick Prevention On, Off Rewind Tension 300x600dpi -1.1pass...
Page 148 SC-F10000 Series User's Guide Control Panel Menu Item Parameter Saving Mode On, Off Print Position Right, Center Right, Center Left, Left Print Head Cleaning Auto Cleaning, Cleaning(Light), Cleaning(Medium), Cleaning(Heavy), Print Head Refresh Cleaning the Maintenance Parts Anti-Drying Caps, Around the Head, Suction Cap, Media Cleaner...
Page 149 SC-F10000 Series User's Guide Control Panel Menu Item Parameter Operation Report Total Print Area, Total Media Feed Length, Total Carriage Pass...
Page 150: Details Of The Menu
SC-F10000 Series User's Guide Control Panel Menu Details of the Menu General Settings menu * indicates default settings. Item Parameter Explanation Basic Settings...
Page 151 Date/Time Set the printer’s built-in clock. The time and date set here are displayed on the Home screen. It is also used for job logs and the printer's status as shown in Epson Edge Dashboard. Time Difference -12:45 to +13:45 Set the time difference with coordinated universal time (UTC) in 15 minute increments.
Page 152 SC-F10000 Series User's Guide Control Panel Menu Item Parameter Explanation Language Japanese Select the language used in the control panel display. English French Italian German Portuguese Spanish Dutch Russian Turkish Korean Simplified Chinese Traditional Chinese Background Color Gray Select the color scheme used in the control panel display. You can set a color scheme that is easy to see in the environment in which the printer is installed.
Page 153 SC-F10000 Series User's Guide Control Panel Menu Item Parameter Explanation Margins Side(Right) Choose the width of the right margin when media is loaded in the printer. 3 to 25 mm (7 See the following for more information. “Printable area” on page 95 Side(Left) Choose the width of the left margin when media is loaded in the printer.
Page 154 SC-F10000 Series User's Guide Control Panel Menu Item Parameter Explanation Information Printing When this is turned On, a mark and the nozzle check pattern are printed on the end of the media, so it is easier to check print quality.
Page 155 SC-F10000 Series User's Guide Control Panel Menu Item Parameter Explanation Actions after Media The printer constantly monitors for striking of the media and print head Stop Immediately Scuffing while printing, so set the operation for when striking occurs. Stop when...
Page 156 SC-F10000 Series User's Guide Control Panel Menu Item Parameter Explanation Information Printing at Media Cut When the media is cut, information, such as the remaining amount of media, is printed before and after the cut position. The information is Paper Remaining In‐...
Page 157 SC-F10000 Series User's Guide Control Panel Menu Item Parameter Explanation Cleaning Setting The printer constantly monitors the condition of the print head nozzles while printing, so set the operation for when clogged nozzles (missing Threshold Of Clog‐ nozzles) are detected during monitoring.
Page 158: Media Settings Menu
SC-F10000 Series User's Guide Control Panel Menu Item Parameter Explanation Advanced Do a variety of network settings. Device Name TCP/IP Proxy Server Email Server Server Settings Connection Check IPv6 Address Enable Disable Link Speed & Duplex Auto 10BASE-T Half Duplex...
Page 159 Manual(Measureme Media Management 01 XXXXXXXXXX to 50 XXXXXXXXXX Change the registered media settings. New registrations are normally done when loading media or in advance on the provided Epson Edge Dashboard. “Media Setting Item” on page 160 Manage Remaining Amount Manage Remaining...
Page 160 Media Setting Item When loading media, select Media Type or register the media settings on the printer using the supplied Epson Edge Dashboard, to set the optimal media setting values. Normally, use this as it is. When using specific media or when a problem such as head striking or banding is detected in printing results, change the settings.
Page 161 SC-F10000 Series User's Guide Control Panel Menu Item Parameter Explanation Pass Mode 300x600dpi -1.1pass Pass Mode allows you to register the setting values, for each number of passes, of 3 items, Temperature, Drying Time, and Rewind Tension in the 300x600dpi -1.5pass Advanced Settings.
Page 162 SC-F10000 Series User's Guide Control Panel Menu Item Parameter Explanation Dryer Heater Select whether to use (On)/not use (Off) the heater to dry media after printing. Temperature Set the heater's temperature. You can set it for each number of passes.
Page 163 SC-F10000 Series User's Guide Control Panel Menu Item Parameter Explanation Set the heater to Off, and by setting the Fan to Low or High so media is dried after printing by only the fan operating at the set level. Use this if the media could be damaged by the heater during drying.
Page 164 SC-F10000 Series User's Guide Control Panel Menu Item Parameter Explanation Feeding Tension Lv1 to Lv4 Normally, use the default setting values. Increase tension if creases appear in the media during printing. The higher the value, the greater the tension. Paper Suction Lv0 to Lv10 Set the strength of the suction by the platen on the media.
Page 165: Maintenance Menu
SC-F10000 Series User's Guide Control Panel Menu Item Parameter Explanation Rewind Tension Normally, use the default setting values. The higher the value, the greater the tension. 300x600dpi -1.1pass Lv1 to Lv9 If creases appear in the media while printing, we recommend setting a smaller value.
Page 166: Supply Status Menu
SC-F10000 Series User's Guide Control Panel Menu Item Parameter Explanation Print Head Cleaning Auto Cleaning Execute Print Head Cleaning. Perform Auto Cleaning first. If the clogs are not cleared by doing it, then do in the order of Cleaning(Light), Cleaning(Light) Cleaning(Medium), and Cleaning(Heavy) until the clogs are cleared.
Page 167: Replacement Part Information Menu
Ink Tube Printer Status menu Item Parameter Explanation Firmware Version Shows and prints the selected information. The Printer Name is the name set in Epson Edge Dashboard. Printer Name Fatal Error Log Operation Report Total Print Area Total Media Feed Length...
Page 168: Problem Solver
SC-F10000 Series User's Guide Problem Solver Problem Solver When a Message is Displayed If one of the following messages is displayed, read and follow the instructions below. Messages What to do The waste ink bottle is nearing the end of The Waste Ink Bottle is getting full.
Page 169: When An Error Message Is Displayed
One of the parts in the printer is nearing printer. the end of its service life. Contact your dealer or Epson Support and tell them the maintenance request Note the code and call for service. code. End Of Parts Service Life XXXXXXXX...
Page 170 Turn the power off and on again. printer, disconnect the power cable from the outlet and from the AC inlet on the If the problem persists, contact Epson printer, and then reconnect. Turn on the printer again multiple times. Support.
Page 171: Troubleshooting
OFF, turn it ON, and try turning on the power. If it immediately turns OFF, unplug the power cord and contact your local dealer or Epson service call center. Connect the printer directly to the computer using a USB cable, and then try to print.
Page 172: The Printer Sounds Like It Is Printing, But Nothing Prints
Are you using a genuine Epson ink cartridge? “Print Head Cleaning” on page 136 This printer is developed for use with Epson ink cartridges. If you use non-Epson ink cartridges, printouts may be faint, or the color of the printed...
Page 173 SC-F10000 Series User's Guide Problem Solver Are media settings correct? Is the media skewed? Confirm that the media settings in the software RIP or If the media is not loaded correctly, the media may on the printer match the media actually in use.
Page 174: Media
SC-F10000 Series User's Guide Problem Solver Move the lock levers on the left and right sides Media outwards to open the front cover. Media Jams. Is media curled, folded, curved, creased, or waved? Cut and remove the curled, folded, curved, creased, or waved part.
Page 175 SC-F10000 Series User's Guide Problem Solver Raise the media loading lever. Move to the back side, and take up the media by operating the drive switch according to how the media is rolled. Use scissors, at the platen, to cut away the torn or Move to the front side, check the platen, and if wrinkled parts.
Page 176: Others
Forgotten password for network setup protection Contact your dealer or Epson Support. The red light is on inside the printer. This is not a failure. The red light is a light inside the printer.
Page 177: Appendix
SC-F10000 Series User's Guide Appendix Appendix For the latest information, see the Epson Web site. (as of January, 2020) Options and Consumable Products Ink cartridges Printer model Product Part number SC-F10000 Ink cartridges (10000 ml) High Density Black T43H1 SC-F10060...
Page 178: Others
Epson recommends the use of genuine Epson ink cartridges. Epson cannot guarantee the quality or reliability of nongenuine ink. The use of non-genuine ink may cause damage that is not covered by Epson's warranties, and under certain circumstances, may cause erratic printer behavior.
Page 179: Supported Media
SC-F10000 Series User's Guide Appendix Supported Media Moving and Transporting the Printer The following media can be used with the printer. This section describes how to move and transport the Print quality is greatly affected by the type and quality of product.
Page 180 SC-F10000 Series User's Guide Appendix Pull screw (3) out as is. Important: ❏ The printer can be moved across bumps of less than 5 mm and gaps of less than 30 mm. Before you start, check the bumps and gaps of the route to move the printer.
Page 181 SC-F10000 Series User's Guide Appendix Loosen the screw shown in the illustration inside Lightly tighten the screw. the front cover about halfway. If a screw is difficult to loosen by hand, use a hex wrench. Insert the screws removed in Step 5 into the 2 holes in the bottom part of the anchor, and lightly tighten them.
Page 182 SC-F10000 Series User's Guide Appendix Loosen and remove the 2 screws inside the Insert the screw removed in Step 5 into the hole maintenance cover, as shown in the illustration. in the bottom part of the anchor, and lightly tighten it.
Page 183 SC-F10000 Series User's Guide Appendix (3) Continue to turn it counter-clockwise until the “Removing the Loaded Media” on page 87 adjuster is higher than the caster. On the left side, raise the center adjuster so it is higher than the caster.
Page 184 SC-F10000 Series User's Guide Appendix Post-Move Installation Repeat Steps 19 and 20 on the right side to raise those adjusters so they are higher than the After moving the printer, follow the steps below to ready casters. it for use.
Page 185 SC-F10000 Series User's Guide Appendix Use a hex wrench to loosen the 3 screws on Use a hex wrench to loosen and remove the 2 anchor B, and then remove the screws and bottom screws on anchor A. anchor B.
Page 186 SC-F10000 Series User's Guide Appendix Tighten the top screw. Align anchor A and B with the screw hole positions on the printer as shown in the illustration. Open the right-side maintenance cover. Use the screws removed in Steps 3 and 5, and insert and tighten 2 of them into screw holes (1) and (2), and insert 1 of them into hole (3).
Page 187 SC-F10000 Series User's Guide Appendix Place the metal plates under the printer's 6 Adjust the adjusters so the printer is level. adjusters. Turn the bottom nut of the adjuster until the air bubble in the level gauge is centered. On the right side, use the front and back adjusters on the printer to suspend the casters.
Page 188 SC-F10000 Series User's Guide Appendix When the air bubble is toward the front side On all 6 adjusters, turn the top nut clockwise until it reaches the top part and stops. Turn the nut on the back adjuster clockwise. After it reaches the top part, tighten it securely to fix it.
Page 189: Transport
SC-F10000 Series User's Guide Appendix The illustration shows an example of pressure Transport rollers pressing on the right end of the media. If the edge of the media is in the A position, install Before transporting the printer, contact your dealer or the spacers on the pressure rollers.
Page 190: How To Remove Spacers
SC-F10000 Series User's Guide Appendix Move to the back side and remove the spacers How to remove spacers from where they are stored. Raise the media loading lever. Move to the back side and remove the 4 spacers Insert the spacers into the holes on the back side and return them to where they are stored.
Page 191: Parallel Adjustments For The Auto Take-Up Reel Unit
SC-F10000 Series User's Guide Appendix Parallel Adjustments for 1. Checking the Parallelism the Auto Take-up Reel Attach the adjustment tool to confirm there is no misalignment in the parallelism of the Auto Take-up Reel Unit. If there is no misalignment, then adjustment is not Unit necessary.
Page 192 SC-F10000 Series User's Guide Appendix Remove the screws in the illustration below, and Important: then turn the cover to open it. If the left-side media holder handle's shaft is not visible, rotate the handle as shown in the illustration until it stops. The roll core cannot be properly loaded if the handle's shaft is not visible.
Page 193 SC-F10000 Series User's Guide Appendix Pass film through the roll core. Move the film to the left side, insert its leading edge into the printer, and pass it through to the back side. Insert it into the bottom of the dryer and then out the top part, over the platen and through to the back.
Page 194 SC-F10000 Series User's Guide Appendix Align the film with the tips of the triangles on the After the film stops swinging, read the value on top and bottom of the left side of the dryer. the scale at the position on the platen shown in the illustration, and record that value.
Page 195 SC-F10000 Series User's Guide Appendix “Completing Adjustments” on page 197 Completely loosen the adjustment screws on both sides in the illustration below. Confirm that the film is aligned with the tips of the triangles on the right side, read the value on the scale at the position on the platen shown in the illustration, and record that value.
Page 196 SC-F10000 Series User's Guide Appendix (2) While checking the scale, turn the adjustment Move the film to align with the tips of the screw clockwise until the difference in the triangles on the left side. values for both sides is less than 0.5 mm.
Page 197 SC-F10000 Series User's Guide Appendix Completing Adjustments Loosen the right media holder fixing screw and remove the media holder. Remove the weight attached to the film at the back of the printer. Remove the roll core. Pull film out from the front of the printer.
Page 198 SC-F10000 Series User's Guide Appendix Loosen the locking screw on the left media holder locking screw and move the left and right media holders inward. Turn the cover in the illustration below to close it, and then tighten the screw.
Page 199: Media Settings List For Each Media Type
SC-F10000 Series User's Guide Appendix Media Settings List for Each Media Type The following table shows the media settings registered when a Media Type is selected. Ultra-Thin Pass Mode (*: Default value) 1200x 300x600dpi 600x600dpi 600x1200dpi 1200dp Item 5.0pas 9.0pass...
Page 200 SC-F10000 Series User's Guide Appendix Thin Pass Mode (*: Default value) 1200x 300x600dpi 600x600dpi 600x1200dpi 1200dp Item 5.0pas 9.0pass s HD Heater Temperature Drying Time Proceed to Drying after Print Drying Action Auto Platen Gap Feeding Tension Paper Suction Media Feed Speed...
Page 201 SC-F10000 Series User's Guide Appendix Med-Thick Pass Mode (*: Default value) 1200x 300x600dpi 600x600dpi 600x1200dpi 1200dp Item 5.0pas 9.0pass s HD Heater Temperature Drying Time Proceed to Drying after Print Drying Action Auto Platen Gap Feeding Tension Paper Suction Media Feed Speed...
Page 202: How To Read The Signal Lamps
SC-F10000 Series User's Guide Appendix Thick Pass Mode (*: Default value) 1200x 300x600dpi 600x600dpi 600x1200dpi 1200dp Item 5.0pas 9.0pass s HD Heater Temperature Drying Time Proceed to Drying after Print Drying Action Auto Platen Gap Feeding Tension Paper Suction Media Feed Speed...
Page 203 SC-F10000 Series User's Guide Appendix Green Yellow Status Explanation Power off The power is off. Doing start up operations after the Starting/stopping Flashing power is turned on, or doing shut down operations operations after the power is turned off. Idling Idling in a normal state.
Page 204: System Requirements
The Epson Edge Dashboard can be used in the following environments. Important: Make sure the computer on which the Epson Edge Dashboard is installed meets the following requirements. If these requirements are not met, the software cannot monitor the printer correctly.
Page 205: Epson Edge Print
SC-F10000 Series User's Guide Appendix Display resolution 1280 x 1024 or better Communication interface High Speed USB Ethernet 1000Base-T Browser Safari 6 or later Linux Distribution Debian 8.6 64 bit (MATE desktop environment only) or later Multi-core processor (3.0 GHz or more recommended)
Page 206: Web Config
SC-F10000 Series User's Guide Appendix Web Config Windows Browser Internet Explorer 11, Microsoft Edge, Mozilla Firefox , Google Chrome * Use the latest version Browser Safari , Mozilla Firefox , Google Chrome * Use the latest version...
Page 207: Specifications Table
SC-F10000 Series User's Guide Appendix Specifications Table Printer Specifications Temperature and humidity range Gray area: While operating Printer Specifications Cross-hatch line area: Recommended Printing method On-demand ink jet Nozzle configuration 400 nozzles x 2 rows x 4 chips x 4...
Page 208 SC-F10000 Series User's Guide Appendix Important: Interface Specifications Use this printer at altitudes below 2000 m. USB port for a USB 3.0 (SuperSpeed USB) computer Warning: Wired LAN 1000Base-T compliance This is a class A product. In a domestic environment...
Page 209 SC-F10000 Series User's Guide Appendix Interface Specifications Ink Specifications Security IEEE802.1X (Ethernet) standards/ Type Special ink cartridges IPsec (v4/v6), IP filtering protocols Sublimation dye High Density Black, Cyan, Magenta, SSL/TLS: Yellow Use by date See the date printed on the ink...
Page 210: Where To Get Help
Support Technical Support Web Before Contacting Epson Site If your Epson product is not operating properly and you cannot solve the problem using the troubleshooting Epson's Technical Support Web Site provides help with information in your product documentation, contact problems that cannot be solved using the Epson support services for assistance.
Page 211: Help For Users In North America
Friday. Days and hours of support are subject to change without notice. Toll or long distance charges may apply. ❏ Product usage questions or problems Before you call Epson for support, please have the ❏ Enquiries on repair service and warranty following information ready: ❏...
Page 212: Help For Users In Australia/New Zealand
No.530, Sec. 4, Henan Rd., Nantun Dist., Taichung City 408, Epson Helpdesk Taiwan Epson Helpdesk is provided as a final backup to make 05-2784222 05-2784555 No.463, Zhongxiao Rd., East Dist., Chiayi City sure our clients have access to advice. Operators on the...
Page 213: Help For Users In Thailand
SC-F10000 Series User's Guide Where To Get Help Epson HelpDesk World Wide Web (Phone: (65) 6586 3111) (https://www.epson.co.id) Our HelpDesk team can help you with the following ❏ Information on product specifications, drivers for over the phone: download ❏ Sales enquiries and product information ❏...
Page 214: Help For Users In Hong Kong
603-56288222 Internet Home Page ❏ Enquiries on repair services & warranty, product usage and technical support (Techline) Epson Hong Kong has established a local home page in both Chinese and English on the Internet to provide Phone: 603-56288333 users with the following information: ❏...
Page 215 SC-F10000 Series User's Guide Where To Get Help Helpdesk (63-2) 706 2625 Direct Line: E-mail: epchelpdesk@epc.epson.com.ph World Wide Web (https://www.epson.com.ph) Information on product specifications, drivers for download, Frequently Asked Questions (FAQ), and E-mail Enquiries are available. Toll-Free No. 1800-1069-EPSON(37766) Our Hotline team can help you with the following over the phone: ❏...

This manual is also suitable for:

Sc-f10000Sc-f10060 Sc-f10030 Sc-f10080

Epson SC-F10000 Series User Manual

Notes on Manuals

Basic Operations

Maintenance

Control Panel Menu

Problem Solver

Appendix

Where to Get Help

Quick Links

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Epson SC-F10000 Series

Summary of Contents for Epson SC-F10000 Series

This manual is also suitable for:

Table of Contents