Load And Test Cycle Function Number - Maytag MVWB835DW Service Manual

FOR SERVICE TECHNICIAN'S USE ONLY
'off' to 'on' or from 'on' to 'off'. If the selected
function is currently active (commanded
'on'), the seven segment display will flash
the function number at a 1 Hz rate (1 flash per
second). If the function is currently commanded
'off', the seven segment display will show
the function number without flashing. NOTE:
Activating any of the spin or agitate functions
will result in functions 10–14 reporting their
status as 'on' because reported status is based
on motor motion being commanded.
Chart 1 – Load and Test Cycle Function Number
NOTE: Some functions will not be available on all models
Display
000 Toggle Lid Lock
001 Toggle Cold Valve
002 Toggle Hot Valve
003 Toggle Fresh Fill Valve
004 Toggle Detergent Valve
005 Toggle Fabric
Softener Valve
006 Toggle Oxi Valve
007 Toggle Bleach Valve
008 Toggle Drain Pump
009 Toggle Recirc. Pump
010 Toggle Low
Speed Spin
011 Toggle Mid
Speed Spin
012 Toggle High
Speed Spin
013 Toggle Slow Agitate
014 Toggle Fast Agitate
015 Toggle Shifter
016 Toggle Basket Light
017 Toggle Heater
050 Run Factory Calibration
051 Service Diagnostics
Verification Cycle
052 Run Load Size
Calibration Cycle
053 Run Dry Factory
Calibration Cycle
075 Set Life Test Mode
PAGE 4
Function
Note: To lock or unlock the lid, all functions (pumps, motor,
valves, and heater) must be off and the lid must be closed.
N/A
N/A
For water to flow, cold water should be turned on first.
Note: If the fabric softener valve is turned "ON" without the
cold water valve "ON", water can overflow the front of the tray.
For water to flow, hot water should be turned on first.
Note: If the Oxi valve is turned "ON" without the hot water valve
"ON", water can overflow the front of the tray.
Note: Oxi not available on all models.
Note: On models with dump bleach dispenser, toggling this load
will turn on the Oxi valve.
Note: Not available on all models.
Lid must be closed and locked for this to be enabled.
Note: The basket must be empty for this function.
Lid must be closed and locked for this to be enabled.
Note: The basket must be empty for this function.
Lid must be closed and locked for this to be enabled.
Note: The basket must be empty for this function.
Lid must be closed and locked for this to be enabled.
Note: The basket must be empty for this function.
Lid must be closed and locked for this to be enabled.
Note: The basket must be empty for this function.
Switch in and out of Spin. Shifter On = Spin and Shifter Off =
Agitate. Note: This can only be commanded while the motor is
not running. The shifter will also be on when spin functions
10–12 are active.
N/A
Note: To actuate the heater, all functions (pumps, motor, and valves)
must be off and water level must be above the impeller.
Note: For factory test only.
Service Diagnostics for repair verification and installation
verification. The Soil Level and Temperature buttons can be
used to review step results if Pass/Fail criteria exist. If a step
has no Pass/Fail criteria, --- will be displayed.
This calibrates the main control to the washer for optimal load size
sensing. Upon completion, the UI will display 000.
Note: For factory test only.
Note: For factory test only. If life test mode is accidentally
activated, Life Test can be exited by removing power from the
washer and waiting for the control to power down as indicated
by the diagnostic LED ceasing to flash (see Figure 1, page 2).
Failure to Turn Function On Indication
If the number of functions (pumps, valves,
and motor) allowed on at the same time or
the conditions to actuate the function are not
correct, the display will turn off momentarily
and a tone will sound.
The chart below indicates function and test
cycle function numbers:
Notes
DO NOT REMOVE OR DESTROY