Bernini Self-Contained 4-in-1 Fountain Tower with Planter Bowl Owner's Manual

*PLEASE READ THESE INSTRUCTIONS COMPLETELY BEFORE ATTEMPTING TO ASSEMBLE YOUR NEW FOUNTAIN
CONTENTS:
Dancing Water
Self-Contained
Fountain Tower
Please note, images of parts
are not to scale with one another.
STEP
2.

Assembly

Battery Compartment Battery Compartment
Retaining Screws X2 Retaining Screws X2
Figure 1a
Figure 1b
Battery Cover Battery Cover
O-Rings O-Ring
Figure 3a
1. Take the Fountain Top/Battery Compartment and Water Pump, connect one side of the Water Tube to the Water Pump and the other end to the bottom side of the
Battery Compartment (A & B of Figure 4).
2. Find a suitable bowl and place it on a flat, level surface. Place the Fountain Base, without the Fountain Top with Battery Compartment and Water Pump, into the center of the bowl.
3. Lower the Fountain Top with Battery Compartment and Water Pump into the Fountain Base.
you align the Fountain Top to the Fountain Base. Fit these into place and your Fountain Top and Base should be secure. Fountain Battery Compartment should be flush with fountain top (Figure 6).
4. Fill bowl with water, water level should be 4 inches from the bottom of the Fountain Base. (Diagram 1a).
STEP 3.
Turn Fountain on and set timer: When the Fountain is off, set the run time from 1 to 4 hours by slowly pressing the button 1 to 4 times (Figure 7a & 7b). 3 seconds after pressing
the button, the LED light will repeatedly flash the number of times the button was pressed (Figure 7a). This indicates the number of hours the Fountain will run every day. The
Fountain will turn on at the same time, for the selected number of hours, daily thereafter.
Stop Fountain for one day: To stop the Fountain manually for one day, press the button once (Figure 7a & 7b). The Fountain will turn off for one day, but will still turn on at the same time,
for the same number of hours selected, daily thereafter.
Reset/Change the timer: To change the run time, stop the Fountain if its running by press the button once (Figure 7a & 7b). The Fountain will stop. Once the Fountain is off, you can press
the button again to set the duration (See Step 1). Fully shut off and clear timer: To fully turn off the Fountain so that it will not turn on automatically the next day, press the button once to
turn it off (Figure 7a & 7b). When the Fountain is NOT operating, simply press hold the button again for over 2 seconds, the LED will come on for 3 seconds steady to confirm daily program
is off.
DANCING WATER ATTACHMENTS: (OPTIONAL): To prevent overspray there are 3 Dancing Water Attachments designed for large bowls and 1 designed for small bowls please use
accordingly. When Fountain is not running, select one of the Dancing Water Attachments and attach to the outlet in the middle of the Fountain Tower (Figure 8a, 8b & 8c).
Button Button
Figure 7a
Self-Contained 4-in-1 Fountain Tower with Planter Bowl
Diagram 1a:
Start/Stop
Button
Battery
Attachments
Compartment
Screws x2
Max. Water
Level
(2 inches
from top of
Planter Bowl)
Battery Compartment,
Water Tube
& Water Pump
Locating Locating
Figure 2a
Figure 7: (Below)
On Spout Side of
Self-Contained
Fountain Tower
Align LED to
arrow for
correct placement.
Figure 3b
Figure 7b
Dowel Dowel
Figure 7
Dancing Water Attachments
Please use accordingly
to prevent overspray
Large Bowls Small Bowls
17 in (43.18cm) 11.5 in (29.21cm)
diameter or to 17 in (43.18cm)
larger bowls diameter bowls
Figure 8a
O W N E R S M A N U A L
STEP

INSTALLING BATTERIES:

1. Lift Fountain Top with Battery Compartment & Water
Pump out of the Fountain Base (Figure 5). Disconnect
Dancing
the Water Tube from the Battery Compartment.
Water
Attachments
2. Unscrew (counter clockwise) the Battery Compartment
Screws and open cover (Figure 1a, 1b). Note: Cover fits tightly
Fountain
Top
4. Insert x2 D Batteries with the (+) side facing up in
Battery Compartment and x2 D Batteries with the (-) facing up in
Battery Compartment (Figure 2a).
Battery
Compartment
5. Reinstall the Fountain Top by aligning the locating dowel in
(4 1.5v D
the Battery Compartment and Fountain Top. Set the Battery
Batteries
Not Included)
Cover down onto the Battery Compartment ensuring the dowel
sets into the alignment hole. Apply pressure and tighten the
Fountain
Battery Cover Screws by turning clockwise. NOTE: Pressure must
Base
be applied to the Battery Compartment while tightening the
Water Pump
screws for the threads to catch and assure the compartment is
Tube
properly sealed. If needed while holding battery compartment
and place upside-down on an even surface to tighten screws.
Planter Bowl

CHANGING BATTERIES:

Minimum
1. Remove any Dancing Water Attachment, lift Battery
Water Level
Compartment and Water Pump out of the Fountain (Figure 5),
(3 inches from
ensure Battery Compartment and Water Pump are completely
bottom of
dry before opening Battery Compartment. It is important that
Fountain Base)
no water enters the Battery Compartment.
Water
2. See Installing Batteries Section above on how to reinstall
Pump
batteries and reassemble.
3. Set the Battery Compartment and Water Pump back into the
Fountain (Figure 6).
A
Figure 2b
B
Figure 4
Figure 8b
TM
Figure 5 Figure 6
Figure 8c