Table of Contents
Advertisement
Quick Links
I. Machine Combination Examples
[MFP 105ppm series]
FS-503+Machine+PF-701
•
FS-503+SD-501+Machine+PF-701
•
(FS-503+SD-501+FD-501+Machine+PF-701)
FS-503+LS-501+Machine+PF-701
•
FS-503+FD-501+Machine+PF-701
•
• For installation procedures for FS-503 + MFP
105ppm series, see pages 3 to 6, and 18 to 19.
• For installation procedures for FS-503 + LS-501
+ MFP 105ppm series, see pages 10 to 12, and
18 to 19.
• For installation procedures for FS-503 + FD-501
+ MFP 105ppm series, see pages 13 to 15, and
18 to 19.
• For installation procedures for FS-503 + SD-501
+ MFP 105ppmseries, see pages 15 to 19.
FS-503
INSTALLATION MANUAL
15AEIXE001SA
Finisher
Applied Machine:MFP 105ppm/COLOR MFP 65ppm
For Product Code 56U*-Z*/564*-7*, A03U, A03V
[COLOR MFP 65ppm series]
FS-503+RU-504+Machine+PF-601
•
FS-503+FD-501+RU-504+Machine+PF-601
•
FS-503+LS-501+RU-504+Machine+PF-601
•
FS-503+SD-501+FD-501+RU-504+Machine+PF-601
•
• For installation procedures for FS-503 + RU-504
+ COLOR MFP 65ppm series, see pages 7 to 10,
and 18 to 19.
• For installation procedures for FS-503 + LS-501
+ RU-504 + COLOR MFP 65ppm series, see
pages 10 to 12, and 18 to 19.
• For installation procedures for FS-503 + FD-501
+ RU-504 + COLOR MFP 65ppm series, see
pages 13 to 15, and 18 to 19.
• FS-503 + SD-501 + FD-501 + RU-504 + COLOR
MFP 65ppm series, see pages 15 to 19.
*
When installing the FS-503 on the COLOR
MFP 65ppm series, a RU-504 is required.
E-1
15AEIXE002SA
15AE955011
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Konica Minolta FS-503
Summary of Contents for Konica Minolta FS-503
- Page 1 13 to 15, and 18 to 19. + MFP 105ppmseries, see pages 15 to 19. • FS-503 + SD-501 + FD-501 + RU-504 + COLOR MFP 65ppm series, see pages 15 to 19. When installing the FS-503 on the COLOR MFP 65ppm series, a RU-504 is required.
- Page 2 Accessory parts M4x6 15AEIXE003SA 11. TP screw M4x10 12. Installation manual [Note: Case of MFP 105ppm series] When FS-503 is installed in MFP 105ppm series, be sure to execute; • Setting of DIP SW • Perform a software update (ISW)
- Page 3 15AEIXE006SA V. Installation Procedure Installation procedure for [FS-503+ MFP 105ppm series] 15AEIXE004SA 3. Pull out the stacker and remove the locking tapes. Remove the locking materials (2 pieces) within the 1. Turn OFF the machine’s Sub and Main switches, stacker.
- Page 4 7. Remove the jumper connector from the clamp. CN-19 Connector cover Jumper connector 15AEIXE008SA 4. Remove the back cover of the FS-503.(5 screws) 15AEIXE065SA 8. Connect the jumper connector to CN-19 on the board. Note: Unless the jumper connector is connected, the ISW cannot be performed.
- Page 5 9. Install the back cover of the FS-503 (5 screws). Note: 10. Remove the protective cover from the connector If the vertical opening between the FS-503 and the of the FS-503, and pull out the connector toward machine is not even and their heights are different, the back cover.
- Page 6 (4) Secure the upper part of the FS-503 to the 13.Install the main tray on the main tray up-down machine with a screw. (TP screw M4x10: 1 pc.) portion on the FS-503 (Truss screw M4x6: 2 pcs.) Note: When installing the main tray, hook the main tray guide holes to the four auxiliary metal hooks and secure the tray.
- Page 7 5. Align the bottom hole of the FS-503 with the posi- Installation procedure for tioning pin on the power supply unit, and lock [FS-503 + RU-504 + COLOR MFP 65ppm series] them by sliding the FS-503 toward the back. For the installation procedure for the RU-504, FS-503 see the RU-503/504 installation manual.
- Page 8 When removing conveyance unit, being to use the lock shaft, keep. Lock shaft 15AQIXC008SA 9. Connect the four FS-503 connector jacks to the connector plugs of the power supply unit. 15AQIXE053SA 12. Pull out the conveyance unit, secure it with screws [TP screw (black) 3x8: 2pcs.: included...
- Page 9 13. Loosen two screws, and remove the connector 16. Install the connector cover on the RU convey- cover on the back side of the RU conveyance ance segment.(2 screws) segment. Note: Put the wire bundled into the RU machine so that it will not get hooked when the conveyance segment is pulled out.
- Page 10 Installation procedure for position or angle of the front cover. If the actuator [FS-503 + LS-501 + MFP 105ppm series] does not turn the interlock switch ON, adjust the [FS-503 + LS-501 + RU-504 position of the actuator adjustment plate as well.
- Page 11 3. Remove the back cover of the FS-503. (5 screws) 7. Install the FS-503 to the LS-501. (MFP 105ppm series only) (1) Connect the four FS-503 connector jacks to the con- nector plugs of the LS-501 on the paper exit side.
- Page 12 TP screws(Black) secure the tray. M3x6 Connector cover Main tray 15AEIXE024SA (4) Secure the upper part of the FS-503 to the LS- 501 with a screw. (TP screw M4x10: 1 pc.) 15AEIXE017SA TP screw M4x10 Truss screws M4x6 15AEIXE014SA (5) Install the Installation plate/4 to secure the 10.
- Page 13 FD-501.(1 screw) Installation plate/3 Installation plate/1 Engraved marking FS503 15AEIXE025SA 3. Remove the back cover of the FS-503. (5 screws) (MFP 105ppm series only) Connector cover 15AEIXE026SA 7. Install the FS-503 to the FD-501. (1) Connect the four FS-503 connector jacks to the connector plugs of the FD-501 on the paper exit side.
- Page 14 FS-503 FD-501 Connector cover Installation plate/1 Holes 15AEIXE029SA (4) Secure the upper part of the FS-503 to the FD- 501 with a screw. (TP screw M4x10: 1 pc.) Bottom 15AEIXE028SA Note: If the vertical opening between the FS-503 and the...
- Page 15 (included in the machine pack- 15AEIXE032SA age) FD-501 Machine RU-504 3. Remove the back cover of the FS-503 (5 screws). (MFP 105ppm series only) Power cord 15AEIXE064SA 11. Perform a software update (ISW). (MFP 105ppm series only) For ISW procedures, see the service manual.
- Page 16 4. Turn OFF DIP SW2. (2) Align the top and bottom holes of the FS-503 (MFP 105ppm series only) to the Installation plate/1 pins, and lock them by sliding the FS-503 to the back. Note: • This procedure is required because by default it is set for a COLOR MFP 65ppm series.(Factory default of SW2: ON)
- Page 17 (4) Secure the upper part of the FS-503 to the SD- 9. Install the main tray on the main tray up-down 501 with a screw. (TP screw M4x10: 1 pc.) portion on the FS-503 (Truss screw M4x6: 2 pcs.) Note:...
- Page 18 VI. Serial Number Registration [For the COLOR MFP 65ppm series] Register the serial number of the FS-503 to the Step machine memory. 1. Plug the power cord into the outlet and turn The location of the serial number is shown in the fig- ON the Main power switch.
- Page 19 IX. Adjustment Data Backup If the FS-503 adjustment data is changed, back up the machine finisher data to the FS-503 memory. If a FS-503 and other optional units are connected, the data will be backed up to both memories at the same time.
Need help?
Do you have a question about the FS-503 and is the answer not in the manual?
Questions and answers