2. Installation procedures Note: • This manual provides the illustrations of the accessory parts and machine that may be <Installations to models C554e/C454e/C364e/ slightly different in shape from yours. In that C284e/C224e/C554/C454/C364/C284/C224/554e/ case, instead of the illustrations, use the 454e/364e/284e/224e> appearance of your machine to follow the Follow the installation procedures starting on page installation procedure.
Page 3
(8) Remove the control panel left cover. <When the Working Table WT-506 is mounted to the (Two screws) main body> Refer to the installation manual for the Working Table WT-506 and remove the working table. (4) Remove the scanner right cover. (Three screws).
Page 4
(11) (13) Route the connector of the authentication unit < C554e/C454e/C364e/C284e/C224e/554e/454e/ through the edge cover shown in the illustra- 364e/284e/224e > tion. Remove the harness from the wire saddle. Disconnect the two connectors, and remove the control panel front cover. Connector Wire saddle (14) Attach the supplied double-faced tape A to the...
Page 5
(16) Open the cover shown in the illustration on the (19) Route the USB cable through the harness right side of the main body. guide and the two wire saddles shown in the illustration. Wire saddles (17) Connect the USB cable to the main body. (20) Route the USB cable as shown in the illustra- Note: tion.
Page 6
<Installations to models C368/C308/C258> (24) Attach the authentication label to the cover at the position shown in the illustration. (1) Turn OFF the power switch and unplug the power cord from the power outlet. (2) Attach the ferrite core supplied with the Authenti- cation Unit AU-201S to the Authentication Unit AU-201S at the position shown in the illustration.
Page 7
(6) Remove the cover shown in the illustration from (9) Remove the five screws and two tabs and the main body. remove the control panel front cover. (One screw and one shoulder screw) Note: Do not use too much force to remove the cover as the harness is connected.
Page 8
(12) Pass the authentication unit connector through (15) Open the right rear cover of the main body and the opening shown in the illustration. remove the screw shown in the illustration. (13) Attach the supplied double-faced tape A to the authentication unit at the position shown in the illustration and stick the unit to the holder.
Page 9
(18) Route the USB cable as shown in the illustra- (21) Place the rest of the USB cable in the space tion. Pull the USB cable up in order to remove between the authentication unit and the main slack. body frame. (22) Insert the tab and close the upper right rear cover.
Page 10
<Installations to models C287/C227/367/287/227> (25) Attach the authentication label to the cover at the position shown in the illustration. (1) Turn OFF the power switch and unplug the power cord from the power outlet. (2) Attach the ferrite core supplied with the Authenti- cation Unit AU-201S to the Authentication Unit AU-201S at the position shown in the illustration.
Page 11
<When the optional Keypad KP-101 is not (6) Remove the cable from the control panel assem- mounted> bly. Remove the cover from the main body as shown in the illustration. (Two screws) <Only when the Locale Interface Kit EK-609 is installed>...
Page 12
(10) Attach the authentication unit holder to the main (12) Connect the USB cable to the local interface body. (One supplied screw A) board unit. Note: Note: Install the holder so that it does not incline. Connect to the port at the near side. <C287/C227>...
3. Configuration procedures (16) Attach the authentication label to the cover at the position shown in the illustration. <Installation of the loadable device driver> Install the AU-201S/AU-201 loadable driver (ICC_LDR.tar) to the main body. (1) Prepare a USB memory where only the loadable device driver is stored in the ROOT directory.