Table of Contents
Advertisement
Quick Links
Gift Kit GK-1
Using the Gift Kit
• To ensure safe usage with a full understanding of this product's performance, please be sure to read
through this manual completely.
• Store this manual in a safe place where it can be referred to when needed.
• Reproduction, citation, or translation, in whole or in part, of this manual is prohibited without express
written consent.
• The contents of this document and the specifications of this product are subject to change without
notice.
• Roland DG Corp. assumes no responsibility for any damage that may occur through use of this prod-
uct, regardless of any failure to perform on the part of this product or of any errors in this document.
Damages include but are not limited to damage caused by the specifications or performance of the
product, damage caused by non-use of the product, and damage caused by deliverables obtained
through use of this product. Such damages can be either direct or indirect.
R1-160810
Advertisement
Table of Contents
Related Manuals for Roland Metaza MPX-95 Gift Kit GK-1
Summary of Contents for Roland Metaza MPX-95 Gift Kit GK-1
- Page 1 • The contents of this document and the specifications of this product are subject to change without notice. • Roland DG Corp. assumes no responsibility for any damage that may occur through use of this prod- uct, regardless of any failure to perform on the part of this product or of any errors in this document.
-
Page 3: Table Of Contents
Movable Center Vise ............................13 Windows® is a registered trademark or trademark of Microsoft® Corporation in the United States and/or other countries. Company names and product names are trademarks or registered trademarks of their respective holders. http://www.rolanddg.com/ Copyright © 2016 Roland DG Corporation... -
Page 5: Using The Gift Kit
Using the Gift Kit Using the Gift Kit... -
Page 6: Getting Started
Getting Started What This Document Assumes • This document describes how to use the MPX-95 optional kit. • Refer to the MPX-95 User’s Manual for information such as important notes and basic usage guidelines for using the MPX-95. Features The Gift Kit includes a center vise that can be used to secure three-dimensional objects that cannot be se- cured using the grid table included with the printer, such as pens, allowing for imprinting to be performed on variously shaped gifts. -
Page 7: Using The Vise
Using the Vise Using the Center Vise Names of Components Vise Retaining screw Mounting to a Metal Printer Insert the protrusions on the bottom of the center vise into the holes on the base table or base plate. Center vise Frame and holes on top of the base plate * This illustration shows a base table and a base plate being used together. - Page 8 Using the Vise Securing the Material • With the center vise, you secure material in place by clamping. Clamp the material in place in the vise, and tighten the retaining screw enough to keep the material from easily coming loose. Be careful not to overtighten, because doing so may damage the material. Vise Retaining screw •...
-
Page 9: Using The Movable Center Vise
Using the Vise Using the Movable Center Vise Names of Components Vise Retaining screw Fine adjustment dial Lock lever Mounting to a Metal Printer With the lock lever side facing toward you, insert the protrusions on the bottom of the movable center vise into the holes on the base table or base plate. - Page 10 Using the Vise Securing the Material 1: Securing with a Vise • Clamp the material in place in the vise, and tighten the retaining screw enough to keep the material from easily coming loose. Be careful not to overtighten, because doing so may damage the material. •...
- Page 11 Using the Vise Securing the Material 2: Securing with Clamp Pins • Secure the material in place using the clamp pins mounted in the holes on the vise. The position of the vise can be adjusted using the retaining screws even when using the clamp pins. Be careful not to over- tighten, because doing so may damage the material.
- Page 12 Using the Vise When the imprint surface height is lower than the clamp pin height The area that can be imprinted will be limited. Set the imprint area according to the illustration below. Clamp pin Imprint surface Clamp pin Material <...
- Page 13 Using the Vise Secure in 4 places To prevent material that moves easily from moving, secure the material using the clamp pins in four locations. Securing using both large and small clamp pins Using a combination of the larger and smaller clamp pins makes it easier to secure the material in a horizontal position even if the bottom surface of the material is not flat.
- Page 14 Using the Vise Adjusting the Position Procedure Press the laser pointer button. The laser pointer is irradiated. If the machine is idle for 5 minutes, the laser pointer is automatically turned off. Adjust the vise unit position. Move the unit so that laser pointer points to the center of the area to be imprinted on the material. Raise the lock lever.
-
Page 15: Location Of Serial Number Label
Location of Serial Number Label Center Vise The serial number can be found on the bot- tom toward the rear. Movable Center Vise The serial number can be found on the bot- tom toward the rear. Using the Gift Kit...