Related Manuals for ToolKitRC M6D
Summary of Contents for ToolKitRC M6D
- Page 1 Manual V1.0 2020.04 www.toolkitrc.com ToolkitRC Technology (Shenzhen) Co.. Ltd @ ToolkitRC 2020...
-
Page 2: Introduction
Introduction Thank you for purchasing the ToolkitRC M6D multi-function charger, please read this manual carefully before use. Key Points Tips Important Information Further information To ensure you have the best experience with this product please scan the QR code below to stay up to date with news, information and firmware updates for your charger. -
Page 3: Safety
Safety 1，M6D allows input voltage of 7-28V. Please ensure that the power supply voltage is in line with this range. Pay attention to the positive and negative polarities of the power supply when connecting. 2，Do not use this product in a hot area or near a heat source. -
Page 4: Table Of Contents
Contents Introduction ............2 Key Points ............. 2 Further information..........2 Safety ..............3 Contents..............4 M6D Layout ............8 Quick start ............. 9 Charge and discharge settings ....... 11 1，Battery type ........... 11 2，Number of cells........... 14 3，Mode............. 15 4，Discharge mode.......... 16 5，Input MaxVoltage ........ - Page 5 9，Loop setting..........22 10，Power mode setting ........24 11，Smart battery ..........24 Charge and discharge work......26 System settings..........31 other functions...........35 Specification ............37 @ ToolkitRC 2020...
- Page 6 Product description M6D is a dual-channel balanced charger product. Small size, high power density, innovative design, charging accuracy can be as low as 5mV.. Charge, discharge and balance management of LiPo, LiHV, LiFe Lion 1-6S, NiMh 1-16S, PB 1-10S batteries.
- Page 7 USB 2.1A@5.0V output, rechargeable mobile device. The device connects to PC like a USB drive for easy firmware upgrades. Simply copy and paste new firmware files to update. @ ToolkitRC 2020...
-
Page 8: M6D Layout
M6D Layout Scroll wheel Turn: left or right Exit key Display Press: OK CH key Main port Balance port Temp. Sensor Port Front Input port USB Output Cooling fan &upgrade Back @ ToolkitRC 2020... -
Page 9: Quick Start
Quick start 1，Connect a 7-28V power supply or input battery to the input port on the back of the M6D. 2，The display shows the boot logo and stays for 2 seconds. 3，At the same time accompanied by do-re-mi's boot sound. - Page 10 1，Short press [Scroll Wheel] once， to confirm the key function 2，Press and hold [Scroll Wheel] for 2 seconds， to delete the key function 3，If any key is operated successfully, there will be a di-di prompt tone. ================================= @ ToolkitRC 2020...
-
Page 11: Charge And Discharge Settings
1，Battery type Scroll [Scroll Wheel], move the cursor, select the stored battery type, or create a new battery, press [Enter] to enter the battery setting interface, the display is as follows: @ ToolkitRC 2020... - Page 12 Move the cursor to [Battery Type] and press [OK] to modify the battery type, as shown below: The charger supports charging and discharging of 6 types of batteries: Lipo, LiHV, LiFe, Lion, NiMh, and PB. And two modes of power supply and the smart battery @ ToolkitRC 2020...
- Page 13 3.30V and a fully charged battery of 3.60V. 4, Lion: often referred to as a lithium-ion battery with a nominal voltage of 3.60V and a fully charged battery of 4.10V. 5, NiMh: often called NiMH battery, nominal voltage 1.20V. @ ToolkitRC 2020...
-
Page 14: 2，Number Of Cells
Turn [Scroll wheel] to adjust the value. When set to [Auto], the charger will automatically recognize the number of connected battery cells according to the battery voltage connected to the output port. Short press [OK] and [Exit] to take effect and return to the previous interface. @ ToolkitRC 2020... -
Page 15: 3，Mode
3，After Lixx battery is connected to the balance port, the number of battery cells can be more accurately identified. =================================== 3，Mode Move the cursor to [Mode] and press [OK] to modify the working mode, as shown below: @ ToolkitRC 2020... -
Page 16: 4，Discharge Mode
When the working mode selects discharge, storage, and cycle mode, the battery setting interface will increase the discharge mode. As shown below. Move the cursor to [Discharge Mode] and press [OK] to modify the discharge mode, as shown below. @ ToolkitRC 2020... -
Page 17: 5，Input Maxvoltage
M6D supports two discharge modes. 1. Inter (Internal) Mode, discharge through internal heat consumption, maximum support 3.0A@12W discharge. 2. Recycle mode, when the input is a suitable battery, this function can recover the electric energy from the discharging battery to the input battery, the maximum support is 15.0A@250W discharge. -
Page 18: 6，End Voltage（Tvc
================================= 6，End voltage（TVC） Move the cursor to [End Voltage] and press [OK] to modify the end voltage of the single battery. When the working mode is charging, it is the charging cut-off @ ToolkitRC 2020... - Page 19 2 ， If not familiar with battery characteristics, please do not modify the cut-off voltage. 3，The charging cut-off voltage can be set to a range of plus or minus 50mV of full voltage. 4, Glossary explanation: TVC: English abbreviation for terminal voltage control =================================== @ ToolkitRC 2020...
-
Page 20: 7，Current Setting
1. Please set the charging rate of 1-2C according to the battery capacity. For example: For a battery with a capacity of 2000mAh, please set the charging current to 2.0-4.0A as appropriate. 2. Charging and discharging current are only valid @ ToolkitRC 2020... -
Page 21: 8，Nimh Setting (Peakv)
5mV-15mV, as shown below. =================================== Tips： 1，Only NiMh battery can set negative battery voltage. 2，Glossary explanation: PeakV: When the nickel-metal hydride battery is fully charged, the voltage drop of each piece peaks. ================================= @ ToolkitRC 2020... -
Page 22: 9，Loop Setting
As shown below. Move the cursor to [Cycle times] and press [OK] to set the cycle times to 2-12. The charger will follow the pattern cycle discharging-> charging-> discharging-> charging ... "Discharge-> Charge" is 2 times. @ ToolkitRC 2020... - Page 23 Move the cursor to [Rest time] and press [OK] to set the interval time of the cycle charging. The range is 2 to 10 minutes. As shown below. @ ToolkitRC 2020...
-
Page 24: 10，Power Mode Setting
The range is 0.5A to 15A. 11，Smart battery When the battery type is smart battery, the battery settings are only the drone type and maximum current. As shown below. @ ToolkitRC 2020... - Page 25 Move the cursor to [Drone model] and press [OK] to select different drone models. As shown below. Move the cursor to [Max Current] and press [OK] to set the charging current. The range is 0.5A to 15A. @ ToolkitRC 2020...
-
Page 26: Charge And Discharge Work
Rotate the [Scroll wheel] on this interface to switch the bottom status information and internal resistance voltage value. Short press [OK] to dynamically set the working current or stop working. As shown below. @ ToolkitRC 2020... - Page 27 45.0℃：Charger internal temperature. V: Constant pressure sign. C：Constant current sign. F: Current limit sign. P: power, I: Input overcurrent, C: Maximum current, A: Activate charging, F: The main port is full voltage or a single chip is full voltage. @ ToolkitRC 2020...
- Page 28 As shown below. 1 14mΩ：Internal resistance of the first battery ..Scroll [Scroll Wheel] to switch to the third column of the second channel, which is the information bar. As @ ToolkitRC 2020...
- Page 29 Do not leave charging or discharging batteries unattended. 2. When charging and discharging lithium batteries, only connecting to the main port will not perform balance management. Please pay @ ToolkitRC 2020...
- Page 30 When set to automatically detect the number of battery cells, please pay attention to whether the detected number of cells is consistent with the actual battery. =================================== @ ToolkitRC 2020...
-
Page 31: System Settings
Input power settings: Enter the relevant settings of the power supply. After long-pressing, can select power supply 1, power supply 2, and power supply 3. Short press to expand settings. As shown below. @ ToolkitRC 2020... - Page 32 Max power: the maximum power absorbed from the input port when charging. Max current: the maximum current drawn from the input port during charging. Voltage range: the allowable input voltage range. Charging security Set.: Short press to expand settings. As shown below. @ ToolkitRC 2020...
- Page 33 Support more power. Continuous work: When selected the charger will automatically continue the same charging settings on the next connected battery. Ensure the next connected battery requires the same settings as the previous @ ToolkitRC 2020...
- Page 34 1 to 10 levels Buzzer: The tone of the buzzer can be set to off. Language: The system display language. English, Chinese, etc. can be selected. Default : Restore all settings to factory defaults. @ ToolkitRC 2020...
-
Page 35: Other Functions
1，Firmware upgrade After connecting the M6D to the computer with the USB cable in the box, the computer will recognize a USB disk named Toolkit, download the upgrade file app.upg on the official website Copy and Paste the new file to overwrite the previous files in the USB disk, and the firmware can be upgraded. - Page 36 Just log out or shut down 6，Fully charged When the lithium battery is charged, it prompts "Fast charging has ended". If the battery is not removed, constant voltage trickle charging will be performed automatically to make the battery more fully charged. @ ToolkitRC 2020...
-
Page 37: Specification
（Synchronous mode） Discharging 0.1-15A@250W*2 Recycle Mode Power 0.1-3A@12W*2 Normal Mode 2.1A@5V upgrade@USB3.0 Battery 1.0V-5.0V @1-6S Voltage Battery Internal 1-100mR @1-6S Resistance Display IPS 2.4 inch 320*240 resolution Size 98mm*68mm*35mm Product Weight 220g Size 108.5mm*80.5mm*46mm Individual packing Weight 300g @ ToolkitRC 2020...