Table of Contents
Advertisement
Quick Links
GETTING STARTED GUIDE
NI PXIe-5698
RF Preamplifier Module
Note
Before you begin, install and configure your chassis and controller.
This document explains how to install, configure, and test the NI PXIe-5698 (NI 5698). The
NI 5698 is an RF preamplifier module designed to work with the NI 5668R vector signal
analyzer. The NI 5698 also functions as a stand-alone preamplifier. The NI 5698 ships with the
NI-RFSA instrument driver, which you use to program the device.
To access NI 5698 documentation, navigate to Start»All Programs»National Instruments»
NI-RFSA»Documentation.
Caution
manner not described in this document.
Hot Surface
temperatures and cause burns. Allow the NI 5698 to cool before removing it from
the chassis.
Contents
Electromagnetic Compatibility Guidelines............................................................................... 2
Verifying the System Requirements..........................................................................................2
Unpacking the Kit..................................................................................................................... 2
Verifying the Kit Contents................................................................................................ 3
Preparing the Environment....................................................................................................... 3
Installing the Software.............................................................................................................. 4
Installing the NI 5698............................................................................................................... 4
Direct Connections to the NI 5698................................................................................... 6
Connecting to the NI 5668R............................................................................................. 6
NI 5698 Front Panel.......................................................................................................... 8
Configuring the NI 5698 in MAX.............................................................................................9
Troubleshooting...................................................................................................................... 10
Why Is the ACCESS LED Off When the Chassis Is On?...............................................11
What Should I Do if the NI 5698 Doesn't Appear in MAX?.......................................... 11
What Should I Do if the Module Fails the Self-Test?..................................................... 11
Where to Go Next................................................................................................................... 12
Worldwide Support and Services............................................................................................ 12
The protection provided by this product may be impaired if it is used in a
If the NI 5698 has been in use, it may exceed safe handling
Advertisement
Table of Contents
Related Manuals for National Instruments PXIe-5698
Summary of Contents for National Instruments PXIe-5698
-
Page 1: Table Of Contents
Before you begin, install and configure your chassis and controller. This document explains how to install, configure, and test the NI PXIe-5698 (NI 5698). The NI 5698 is an RF preamplifier module designed to work with the NI 5668R vector signal analyzer. -
Page 2: Electromagnetic Compatibility Guidelines
Furthermore, any modifications to the product not expressly approved by National Instruments could void your authority to operate it under your local regulatory rules. -
Page 3: Verifying The Kit Contents
(IEC 60068-2-1, IEC 60068-2-2) Operating relative humidity 10% to 90%, noncondensing (IEC 60068-2-56) Maximum altitude 2,000 m (800 mbar) (at 25 °C ambient temperature) Pollution Degree Indoor use only. NI PXIe-5698 Getting Started Guide | © National Instruments | 3... -
Page 4: Installing The Software
Remove the black plastic covers from all the captive screws on the module front panel. Identify a supported slot in the chassis. The following figure shows the symbols that indicate the slot types. 4 | ni.com | NI PXIe-5698 Getting Started Guide... - Page 5 11. Cover all empty slots with filler panels or use slot blockers to maximize cooling air flow. NI PXIe-5698 Getting Started Guide | © National Instruments | 5...
-
Page 6: Direct Connections To The Ni 5698
800 MHz RF OUT 4 GHz +25 dBm MAX 0 VDC 10 MHz – 26.5 GHz 3.2 GHz - 8.3 GHz SENSITIVE ALL PORTS Ω 1. Semi-rigid 2.92 mm-to-2.92 mm Coaxial Cable 6 | ni.com | NI PXIe-5698 Getting Started Guide... - Page 7 10 If an issue persists after you complete a troubleshooting procedure, contact NI technical support or visit ni.com/support. Configuring the NI 5698 in MAX on page 9 NI PXIe-5698 Getting Started Guide | © National Instruments | 7...
-
Page 8: Ni 5698 Front Panel
The signal pins of this product's input/output ports can be damaged if subjected to ESD. To prevent damage, turn off power to the product before connecting cables and employ industry-standard ESD prevention measures during installation, maintenance, and operation. 8 | ni.com | NI PXIe-5698 Getting Started Guide... -
Page 9: Configuring The Ni 5698 In Max
Use Measurement & Automation Explorer (MAX) to configure your NI hardware. MAX informs other programs about which devices reside in the system and how they are configured. MAX is automatically installed with NI-RFSA. NI PXIe-5698 Getting Started Guide | © National Instruments | 9... -
Page 10: Troubleshooting
Troubleshooting If an issue persists after you complete a troubleshooting procedure, contact NI technical support or visit ni.com/support. Related Information Connecting to the NI 5668R on page 6 10 | ni.com | NI PXIe-5698 Getting Started Guide... -
Page 11: Why Is The Access Led Off When The Chassis Is On
Windows 7 Select Start»Control Panel»Device Manager. If you are using a PXI or PXI Express controller, verify that a National Instruments entry appears in the system device list. Reinstall NI-RFSA and the device if error conditions appear in the list. If you are using an MXI controller, right-click PCI-to-PCI Bridge, and select Properties from the shortcut menu to verify that the bridge is enabled. -
Page 12: Where To Go Next
The NI website is your complete resource for technical support. At ni.com/support, you have access to everything from troubleshooting and application development self-help resources to email and phone assistance from NI Application Engineers. 12 | ni.com | NI PXIe-5698 Getting Started Guide... - Page 13 United States, visit the Worldwide Offices section of ni.com/ niglobal to access the branch office websites, which provide up-to-date contact information, support phone numbers, email addresses, and current events. NI PXIe-5698 Getting Started Guide | © National Instruments | 13...
- Page 14 CONTAINED HEREIN AND SHALL NOT BE LIABLE FOR ANY ERRORS. U.S. Government Customers: The data contained in this manual was developed at private expense and is subject to the applicable limited rights and restricted data rights as set forth in FAR 52.227-14, DFAR 252.227-7014, and DFAR 252.227-7015. © 2016 National Instruments. All rights reserved. 376530A-01 Apr16...