Jet 54A Operating Instructions Manual page 3

4. Machine specifications
4.1 Technical data
54A:
Jointing width
Table size 1700 x 200mm
Table height
Fence size
Fence tilt
Depth of cut
Number of knives
Cutterhead diameter
No-load speed n
o
Cuts per minute
Cutter knife length
Cutter knife width
Cutter knife thickness
Weight
Mains 230V ~1/N/PE 50Hz
Output power 0,75 kW ( 1 HP) S1
Reference current
Extension cord (H07RN-F): 3x1,5mm²
Installation fuse protection
60A:
Jointing width
Table size 1820 x 230mm
Table height
Fence size
Fence tilt
Depth of cut
Number of knives
Cutterhead diameter
No-load speed n
o
Cuts per minute
Cutter knife length
Cutter knife width
Cutter knife thickness
Weight
Mains 230V ~1/N/PE 50Hz
Output power 1,1 kW ( 1,5 HP) S1
Reference current
Extension cord (H07RN-F): 3x1,5mm²
Installation fuse protection
Mains 400V ~3/PE 50Hz
Output power 1,5 kW ( 2 HP) S1
Reference current
Extension cord (H07RN-F): 4x1,5mm²
Installation fuse protection
4.2 Noise emission
Determined according to EN 859
(Inspection tolerance 4 dB)
Workpiece pine wood:
W=100mm, L=1000mm, moisture
8,5%
Acoustic power level
(according to EN ISO 3746):
Idling LwA 90,0 dB(A)
Operating LwA 97,5 dB(A)
Acoustic pressure level
(according to EN ISO 11202):
Idling
Operating
max 150 mm
The specified values are emission
920mm
levels and are not necessarily to be
950 x 120mm
seen as safe operating levels.
+45°/90°/-45°
Although there is a correlation
max. 8 mm
between emission and imission levels,
3
these do not constitute a basis for
63 mm
determining the necessity of additional
6000 rpm
safety measures.
18000
154mm
Workplace conditions which could
16mm
influence the noise imission level
2,5mm
include the duration of resonance,
142 kg
spatial particulars, other noise
sources etc. For example, the number
of machines and other work being
performed. The permissible workplace
6 A
levels can vary from country to
country.
16A
This information is intended to allow
the user to make a better estimation
max 200 mm
of the hazards and risks involved.
920mm
950 x 120mm
4.3 Dust emission
+45°/90°/-45°
The jointer has been dust emission
max. 8 mm
inspected.
3
At an air velocity of 20 m/s on the dust
78 mm
port dia 100mm:
6000 rpm
Vacuum pressure
18000
Volume flow
205mm
18mm
The machine meets a workplace dust
3mm
emission limit of 2 mg/m³.
160 kg
4.4 Content of delivery
8 A
Jointer assembly
Jointer fence assly.
16A
Belt cover
Belt
Cutter block guard
4 A
Dust chute 100mm
machine stand
16A
Knife setting gauge
Assembly kit
Operating manual
Spare parts list
5. Transport and start up
5.1 Transport and installation
For transport use a forklift or hand
trolley. Make sure the machine does
not tip or fall off during transport.
LpA 82,9 dB(A)
LpA 89,7 dB(A)
600 Pa
565 m³/h
5
The machine is designed to operate in
closed rooms and must be placed
stable on firm and levelled ground.
The machine can be bolted down if
required.
For packing reasons the machine is
not completely assembled.
5.2 Assembly
If you notice any transport damage
while unpacking, notify your supplier
immediately. Do not operate the
machine!
Dispose of the packing in an
environmentally friendly manner.
Clean all rust protected surfaces with
a mild solvent.
Mount the jointer to the machine stand
and connect with 3 lock bolts (A, Fig1)
and 3 spring washers (B, Fig1)
Fig 1
Install the drive belt.
Adjust the belt tension by changing
the motor mounting position.
Install the belt cover (A, Fig 2) with 4
screws and 4 washers (B, Fig 2).
Fig 2
Mount the jointer fence assembly.
Place the key (A, Fig 3) into the
machined slot of the fence support.
Lightly coat the mating surfaces with
oil.