Page 5
Bestimmungsgemäßer Gebrauch von Siemens-Produkten Beachten Sie Folgendes: WARNUNG Siemens-Produkte dürfen nur für die im Katalog und in der zugehörigen technischen Dokumentation vorgesehenen Einsatzfälle verwendet werden. Falls Fremdprodukte und - komponenten zum Einsatz kommen, müssen diese von Siemens empfohlen bzw. zugelassen sein.
Page 6
Warnhinweiskonzept Dieses Handbuch enthält Hinweise, die Sie zu Ihrer persönlichen Sicherheit sowie zur Vermeidung von Sachschäden beachten müssen. Die Hinweise zu Ihrer persönlichen Sicherheit sind durch ein Warndreieck hervorgehoben, Hinweise zu alleinigen Sachschäden stehen ohne Warndreieck. Je nach Gefährdungsstufe werden die Warnhinweise in abnehmender Reihenfolge wie folgt dargestellt.
Betriebsanleitung beschriebenen Verwendung eingesetzt werden. Kombinationen mit Geräten oder Komponenten anderer Hersteller sind erlaubt, wenn diese durch Siemens freigegeben wurden. Eine korrekte und sichere Funktion des Geräts ist nur dann sichergestellt, wenn es entsprechend der Empfehlung transportiert, aufbewahrt, aufgestellt, installiert, benutzt und gepflegt wird.
Muttern: 4x M5, 2x M8 ● 1x Kompaktbetriebsanleitung Lieferumfang prüfen 1. Prüfen Sie die Lieferung auf Vollständigkeit. 2. Setzen Sie sich bei unvollständiger Lieferung oder bei äußeren Beschädigungen mit Ihrem Lieferanten oder der örtlichen Siemens-Geschäftsstelle in Verbindung. Antenne ANT793-8DK A5E03484060-03, 09/2017...
Beschreibung Optionales Zubehör Verbindungsleitung N-Connect/R-SMA Zum Anschließen an SCALANCE W700 mit R-SMA-Anschlüssen, z.B. SCALANCE W700 RJ45, ist die flexible Verbindungsleitung N-Connect/R-SMA Male/Male als Zubehör lieferbar. Länge in m Artikelnummer 6XV1875-5CH50 6XV1875-5CN10 Verbindungsleitung N-Connect/N-Connect Zum Anschluss an einen SCALANCE W700 M12 mit N-Connect oder zur Verbindung mit dem Blitzschutzelement LP798-1N/LP798-2N ist die flexible Verbindungsleitung N-Connect/N-Connect Male/Male als Zubehör lieferbar.
Montieren Wandmontage ① Antenne ② Halteblech zur Befestigung der Antenne ③ Zwischengelenk ④ Halterung ⑤ Bohrungen zur Befestigung an der Wand (4 Stk.) ⑥⑦ Gewindebolzen für Zwischengelenk ⑧ Gewindebolzen zur Befestigung der Antenne (4 Stk.) Bild 3-1 Wandmontage Antenne ANT793-8DK A5E03484060-03, 09/2017...
Page 12
2BMontieren Vorgensweise ② ① 1. Befestigen Sie das Halteblech an der Rückseite der Antenne mit vier ⑧ Gewindebolzen M5 . Verwenden Sie Feder- und Unterlegscheiben. Das Anzugsmoment beträgt 5,7 Nm. ③ ② 2. Befestigen Sie das Zwischengelenk am Halteblech mithilfe des ⑦...
2BMontieren Mastmontage Dicker Mast (1,75''- 3'') Dünner Mast (1'' - 1,75'') ① Klemmbügel ② Halterung ③ Halteblech zur Befestigung der Antenne ④ Antenne ⑤ Gewindebolzen zur Befestigung der Antenne (4 Stk.) ⑥ Gewindebolzen zur Befestigung der Halterung am Halteblech ⑦ Gewindebolzen zur Befestigung am Mast (2 Stk.) Bild 3-2 Mastmontage...
Page 14
2BMontieren Vorgensweise ③ ④ 1. Befestigen Sie das Halteblech an die Rückseite der Antenne mit vier ⑤ Gewindebolzen M5 . Verwenden Sie Feder- und Unterlegscheiben. Das Anzugsmoment beträgt 5,7 Nm. ② ③ 2. Befestigen Sie die Halterung am Halteblech mithilfe des Gewindebolzen ⑥...
Anschließen WARNUNG Lebensgefahr durch Blitzschlag Antennen im Außenbereich müssen sich im Fangbereich eines Blitzableiters befinden. Stellen Sie sicher, dass für alle von außen eingeführten leitfähigen Systeme die Möglichkeit eines Blitzschutz-Potenzialausgleichs besteht. Beachten Sie bei der Umsetzung Ihres Blitzschutzkonzepts unbedingt die Anforderungen der Normen VDE 0182 bzw.
4BTechnische Daten Vorgehensweise 1. Schrauben Sie die flexible Verbindungsleitung zum SCALANCE W700 an die Antenne an. Das Anzugsmoment am N-Connector beträgt 1,7 Nm. 2. Stellen Sie sicher, dass durch die flexible Verbindungsleitung weder für den SCALANCE W700 noch für die Antenne eine Zugbelastung entsteht. Wenn nötig, entlasten Sie die Leitungen.
Maßbilder Antenne Rück- und Seitenansichten Die Maße sind in mm angegeben. Antenne ANT793-8DK A5E03484060-03, 09/2017...
Page 22
5BMaßbilder Halterung Seiten- und Draufansichten Bild 6-1 Maßbild Halterung Die Maße sind in mm angegeben. Antenne ANT793-8DK A5E03484060-03, 09/2017...
Page 23
5BMaßbilder Wandmontage Rück- und Seitenansichten Bild 6-2 Maßbild Wandmontage Die Maße sind in mm angegeben. Antenne ANT793-8DK A5E03484060-03, 09/2017...
Page 24
5BMaßbilder Mastmontage Rück-, Drauf- und Seitenansichten Bild 6-3 Maßbild Mastmontage Die Maße sind in mm angegeben. Antenne ANT793-8DK A5E03484060-03, 09/2017...
Page 25
Marken Alle mit dem Schutzrechtsvermerk ® gekennzeichneten Bezeichnungen sind eingetragene Marken der Siemens AG. Die übrigen Bezeichnungen in dieser Schrift können Marken sein, deren Benutzung durch Dritte für deren Zwecke die Rechte der Inhaber verletzen kann. Haftungsausschluss Wir haben den Inhalt der Druckschrift auf Übereinstimmung mit der beschriebenen Hard- und Software geprüft.
Page 26
Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems.
Page 27
Warning notice system This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage have no safety alert symbol.
The device (and its components) may only be used for the application described in the catalog or the operating instructions. Combinations with devices or components of other manufacturers are permitted it they have been approved by Siemens. Correct and safe operation of the device is guaranteed only when it is transported, stored, set up, installed, used and maintained according to the recommendations.
● 1x Compact operating instructions Checking the components of the product 1. Check that all components are present. 2. If it is not complete or there are signs of external damage, please contact your supplier or your local Siemens office. Antenna ANT793-8DK A5E03484060-03, 09/2017...
Description Optional accessories N-Connect/R-SMA connecting cable For connection to SCALANCE W700 with R-SMA connectors, e.g. SCALANCE W700 RJ45, the flexible connecting cable N-Connect/R-SMA Male/Male can be supplied as an accessory. Length in m Article number 6XV1875-5CH50 6XV1875-5CN10 N-Connect/N-Connect connecting cable For connection to a SCALANCE W700 M12 with N-Connect or for connecting the lightning protection element LP798-1N/LP798-2N the flexible connecting cable N-Connect/N-Connect Male/Male can be supplied as an accessory.
Installation Wall mounting ① Antenna ② Holding plate for securing the antenna ③ Intermediate hinge ④ Support ⑤ Bore holes for securing to the wall (pack of 4) ⑥⑦ Threaded bolts for the intermediate hinge ⑧ Threaded bolts for securing the antenna (pack of 4) Figure 3-1 Wall mounting Antenna ANT793-8DK...
Page 33
8BInstallation Procedure ② ① 1. Secure the holding plate to the back of the antenna with four threaded ⑧ bolts M5 . Use spring washers and normal washers. The tightening torque is 5.7 Nm. ③ ② 2. Secure the intermediate hinge to the holding plate using the threaded ⑦...
8BInstallation Mast mounting Thick mast (1.75''- 3'') Thin mast (1'' - 1.75'') ① Clamping bracket ② Support ③ Holding plate for securing the antenna ④ Antenna ⑤ Threaded bolts for securing the antenna (pack of 4) ⑥ Threaded bolts for securing the support to the holding plate ⑦...
Page 35
8BInstallation Procedure ③ ④ 1. Secure the holding plate to the back of the antenna with four threaded ⑤ bolts M5 . Use spring washers and normal washers. The tightening torque is 5.7 Nm. ② ③ ⑥ 2. Secure the support to the holding plate using the threaded bolt M8x40 and the nut.
Connection WARNING Danger due to lightning strikes Antennas installed outdoors must be within the area covered by a lightning protection system. Make sure that all conducting systems entering from outdoors can be protected by a lightning protection potential equalization system. When implementing your lightning protection concept, make sure you adhere to the VDE 0182 or IEC 62305 standard.
10BTechnical data Procedure 1. Screw the flexible connecting cable for the SCALANCE W700 to the antenna. The tightening torque at the N connector is 1.7 Nm. 2. Make sure that the flexible connecting cable does not cause any tensile load on the SCALANCE W700 nor on the antenna.
Dimension drawings Antenna Rear view and side views The dimensions are specified in mm. Antenna ANT793-8DK A5E03484060-03, 09/2017...
Page 43
11BDimension drawings Support Side views and view from above Figure 6-1 Dimensional drawing support The dimensions are specified in mm. Antenna ANT793-8DK A5E03484060-03, 09/2017...
Page 44
11BDimension drawings Wall mounting Rear view and side views Figure 6-2 Dimensional drawing wall mounting The dimensions are specified in mm. Antenna ANT793-8DK A5E03484060-03, 09/2017...
Page 45
11BDimension drawings Mast mounting Back view, view from above and side views Figure 6-3 Dimensional drawing mast mounting The dimensions are specified in mm. Antenna ANT793-8DK A5E03484060-03, 09/2017...
Page 46
Trademarks All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owner. Disclaimer of Liability We have reviewed the contents of this publication to ensure consistency with the hardware and software described.
Need help?
Do you have a question about the SIMATIC NET ANT793-8DK and is the answer not in the manual?
Questions and answers