Advertisement
6.4.8. Function Setting
This procedure changes the function settings used to control the indoor
unit according to the installation conditions. Incorrect settings can cause
the indoor unit to malfunction. Perform the "Function Setting" according to
the installation conditions using the remote controller.
• Refer to the indoor unit installation manual for details on the function
numbers and setting numbers, before the start of function setting.
1.
Touch the [Function Setting] on the "Maintenance" screen. The
"Function Setting" screen is displayed.
Touch the [Address] on the "Function Setting" screen. The "Address"
screen is displayed.
2.
Touch [ ] or [ ] to select the address of the indoor units to be
confi gured. (To set all indoor units at the same time, touch [All].)
Touch [OK] to return to the Function Setting screen.
3.
Touch the [Function No.] on the "Function Setting" screen. The
"Function No." screen is displayed.
1.
2.
Function Setting
Address
Address
[002–01]
002–01
Function No.
[00]
Setting No.
[00]
Back
Setting
Cancel
4.
Touch [ ] or [ ] to set the function number. Touch [OK] to return to
the "Function Setting" screen.
5.
Touch the [Setting No.] on the "Function Setting" screen. The "Set-
ting No." screen is displayed.
6.
Touch [ ] or [ ] to set the setting number. Touch [OK] to return to
the "Function Setting" screen.
4.
5.
Function No.
Function Setting
Address
00
Function No.
Setting No.
Cancel
OK
Back
7.
Touch [Back] to return to the "Maintenance"
screen.
6.4.9. Installer Password Change
Change the Installer password.
1.
Touch the [Installer Password Change] on the "Maintenance"
screen. The "Installer Password Verifi cation" screen is displayed.
Enter the current password, then touch the [OK].
The default password is "0000" (4 digits).
2.
The "Installer Password Change" screen is displayed.
Enter the new password, then touch the [OK]. It returns to the
"Maintenance" screen.
1.
2.
Installer Password Verification
Installer Password Change
Enter Current Password
Enter New Password
0
0
1
2
3
4
0
CL
CL
5
6
7
8
9
5
Cancel
OK
Cancel
6.4.10. Initialization
Require an Installer password.
1.
Touch the [Initialization] on the "Main-
tenance" screen. Enter the Installer
password. The "Initialization" screen is
displayed.
When the [OK] is touched, this unit restarts
automatically after initialization. Perform
each setting.
When relocating the set remote controller, initialize it.
3.
Function Setting
All
Address
[002–01]
Function No.
Setting No.
OK
Back
Setting
6.
Function Setting
Address
[002–01]
[002–01]
Function No.
Setting No.
[00]
00
[00]
Setting
Cancel
OK
Function Setting
Address
[002–01]
Function No.
Setting No.
Back
Setting
1
2
3
4
6
7
8
9
OK
Initialization
Remote controller will be initialized
to the factory default setting. OK?
Cancel
OK
7. TEST RUN
• Refer to the indoor unit installation manual.
For how to carry out a test run, refer to 6. 4. Maintenance (Other Settings)
→ 6.4.5. Test Run.
8. ERROR CODES
Check the error
1.
If an error occurs, an error icon appears on the "Monitor mode
screen".
Touch the [Status] on the "Monitor mode screen". The "Status"
screen is displayed.
2.
Touch the [Error Information] on the "Status" screen. The "Error
Information" screen is displayed. (If there are no errors, the [Error
Information] will not be displayed.)
3.
2-digit numbers correspond to the error code in the table below.
Touch the [Next page] (or [Previous page]) to switch to other con-
nected indoor units.
1.
[00]
Fri 10:00AM
[00]
Mode
Set Temp.
Fan
Status
Menu
For the details of the indoor unit or outdoor unit error, refer to the error
codes in each installation manual.
Error code
CC.1
Sensor error
C2.1
Transmission PCB error
[00]
12.1
Wired remote controller communication error
Number excess of device in wired remote controller
12.3
system
12.4
Wired remote controller system start-up error
26.4
Address duplication in wired remote controller system
[00]
26.5
Address setting error in wired remote controller system
[00]
15.4
Data acquisition error
2.
3.
Status
Page 1/ 4
Error Information
Air Flow Direction
Address
VT
HZ
02-01
1
3
Error Code
Individual
14,15, 41, 44
Economy
Anti Freeze
Off
Off
Next
Error
Monitor
Back
Page
Information
Contents
Page 1/ 5
Next
Page
En-9
Hide quick links:
Advertisement
