Related Manuals for Childcare Argent 2in1
Summary of Contents for Childcare Argent 2in1
- Page 1 Argent 2in1 Swing High Chair “Aztec Teal” Model # 044286-376 IMPORTANT: RETAIN FOR FUTURE REFERENCE, READ CAREFULLY...
-
Page 2: Safety Precautions
SAFETY PRECAUTIONS Read all instructions before assembly and use of the swing high chair. Keep instructions for future use. WARNING FOLLOW THE MANUFACTURER’S INSTRUCTIONS. DO NOT LEAVE CHILDREN UNATTENDED. THE HARNESS MUST ALWAYS BE USED AND CORRECTLY FITTED - MOST INJURIES FROM HIGH CHAIRS ARE CAUSED BY FALLS. - Page 3 SAFETY PRECAUTIONS WARNING FOLLOW THE MANUFACTURER’S INSTRUCTIONS. DO NOT LEAVE CHILDREN UNATTENDED. IT IS DANGEROUS TO USE THE RECLINED SWING ON AN ELEVATED SURFACE (E.G A TABLE). THIS PRODUCT IS NOT INTENDED FOR PROLONGED PERIODS OF SLEEPING. ALWAYS USE THE RESTRAINT SYSTEM. DO NOT USE THIS PRODUCT ONCE YOUR CHILD CAN SIT UP UNAIDED OR WEIGHS MORE THAN 9KG.
- Page 4 Assembly contents list Assembly / Operating instructions How to care for your Argent 2in1 Swing High Chair Due to variations in the style and design of our products, the photographs and illustrations shown in this instruction manual are generic, therefore product fabrics, colour and design may vary from images shown.
- Page 5 ASSEMBLY CONTENTS Check what you have received... You have received 1 box. Please check the contents of the box against the list below. If anything is missing, please contact Customer Service. In Australia, contact CNP Brands on 1300 667 137, in New Zealand contact Wainhouse Distribution on 0800 567 5000.
- Page 6 ASSEMBLY CONTENTS Supplied loose in box continued: Tray USB Power Cord Alternative Power Supply AA Batteries (Not Included) There are no accessories recommended for use with this Childcare Argent 2in1 Swing High Chair.
- Page 7 ASSEMBLY / OPERATING INSTRUCTIONS To assemble Frame... Insert main module arm into ‘A’ slot of front leg tube until you hear the ‘click’ sound. Insert main support arm into ‘B’ slot of front leg tube until you hear the ‘click’ sound. Insert rear leg ‘U’...
- Page 8 ASSEMBLY / OPERATING INSTRUCTIONS To assemble Seat continued... Attach seat locking bar onto the bottom of the seat assembly frame by lining up the corresponding ‘C’ stickers. Insert until your hear the ‘click’ sound. PLEASE NOTE! Teal release button on locking bar should be facing towards the underside of the seat To attach seat assembly to frame, line up the numbers on the inside plastic of the seat support arms with the...
- Page 9 ASSEMBLY / OPERATING INSTRUCTIONS To assemble Tray... To attach tray to high chair, line up tray insert bars with the slots on the front of the seat assembly. Insert until you hear a ‘click’ sound. To adjust Tray... Tray has 3 lockable positions. To adjust the tray, locate the tray adjustment buttons on both the left and right sides of the underside of the tray.
- Page 10 ASSEMBLY / OPERATING INSTRUCTIONS To adjust Seat Height (High Chair Mode)... Seat has 6 adjustable heights. To adjust seat height, locate seat release levers on both sides of seat assembly. Pull up on both levers simultaneously whilst moving seat up or down to desired position. Ensure the seat assembly ‘clicks’...
- Page 11 ASSEMBLY / OPERATING INSTRUCTIONS To operate Seat Recline... Seat has a 3 position reclineable backrest. To recline backrest, squeeze trigger located on back of seat and lower to desired position. Ensure seat ‘clicks’ into place and is secure. PLEASE NOTE! Seat cannot be fully reclined whilst in lowest height position. To adjust Footrest...
- Page 12 ASSEMBLY / OPERATING INSTRUCTIONS To assemble Harness continued... The harness should be carefully adjusted so that it fits your child comfortably. To adjust the shoulder strap height or to remove the harness, flatten the butterfly ends and pass through the slots in the seat (c). To refit the straps, flatten the butterfly ends, pass the ends through the slots in the seat then open the butterfly ends out (d).
- Page 13 ASSEMBLY / OPERATING INSTRUCTIONS To operate Swing Mode... To begin Swing Mode, ensure seat assembly has been released from frame via the seat locking bar. Turn on power via power button (USB power or battery power is available). Controls as per previous page. To install Batteries (not included)...
- Page 14 ASSEMBLY / OPERATING INSTRUCTIONS To insert USB... To use USB Power Cord, locate connection on the bottom left hinge of product. Insert supplied USB into connection. Insert opposite end into an appropriate power supply (not included with product). To fold for Storage... It is recommended to lower the seat to the lowest height position for storage purposes.
-
Page 15: Maintenance
HOW TO CARE FOR YOUR CHILDCARE 2IN1 SWING HIGH CHAIR Cleaning This product has been designed and developed with safety, comfort and functionality in mind. Please take the time to read this manual carefully before using this product and keep it in a safe place for future reference. - Page 16 Distributed in Australia by CNP Brands Distributed in New Zealand by Wainhouse 20 Calarco Drive, Distribution Derrimut, VIC, 3030 2-6 Argyle St, Morningside, Customer Service 1300 667 137 PO Box 41-014, St Lukes, Auckland, New Zealand W: www.cnpbrands.com.au Customer Service: 0800 567 5000 E: info@cnpbrands.com.au F: www.facebook.com/CNPBrands E: helpline@wainhousedist.co.nz...