H3C WX3800H Series Installation Manual
Hide thumbs
Also See for WX3800H Series:
- Command reference manual (27 pages) ,
- Installation manual (49 pages)
Table of Contents
Advertisement
Quick Links
Contents
Installing the device ·········································································· 1
Confirming installation preparations ······························································································· 1
Installation flow ·························································································································· 2
Mounting the device on a workbench ····························································································· 2
Installing the device in a 19-inch rack ····························································································· 3
Mounting bracket ················································································································· 3
Mounting the device in a rack ································································································· 3
Grounding the device ·················································································································· 5
Grounding the device by using a grounding strip ········································································ 5
Grounding the device by using a grounding point on the rack ························································ 6
Grounding the device by using a grounding conductor buried in the earth ········································ 7
(Optional) Installing network port lightning protectors ········································································· 8
(Optional) Installing a surge protected power strip ············································································· 9
Connecting interface cables ········································································································· 9
Connecting the console cable and setting terminal parameters ····················································· 9
Connecting Ethernet cables ································································································· 10
Installing a power module ·········································································································· 11
Connecting a power cord ··········································································································· 12
Verifying the installation ············································································································· 12
Starting the device ··················································································································· 12
i
Advertisement
Table of Contents
Related Manuals for H3C WX3800H Series
Summary of Contents for H3C WX3800H Series
-
Page 1: Table Of Contents
Contents Installing the device ·········································································· 1 Confirming installation preparations ······························································································· 1 Installation flow ·························································································································· 2 Mounting the device on a workbench ····························································································· 2 Installing the device in a 19-inch rack ····························································································· 3 Mounting bracket ················································································································· 3 ... -
Page 2: Installing The Device
H3C Support for permission. Otherwise, H3C will not be liable for any consequence caused thereby. The installation procedure is the same for the WX3800H series access controllers. This section uses the WX3840H access controller as an example. -
Page 3: Installation Flow
Installation flow Figure 1 Installation flow Mounting the device on a workbench CAUTION: Do not place heavy objects on the device. If a standard 19-inch rack is not available, you can mount the device on a clean, flat workbench. To mount the device on a workbench:... -
Page 4: Installing The Device In A 19-Inch Rack
Place the device upside down. Clean the recessed areas on the chassis bottom. Attach the four rubber feet to the recessed areas on the chassis bottom. Place the device on the workbench with the upside up. Make sure the four rubber feet stand firmly on the workbench. - Page 5 Figure 4 Installing cage nuts Use the M3 screws supplied with the mounting brackets to secure the mounting brackets to both sides of the device. Figure 5 Installing the mounting brackets Supporting the device bottom with one hand and holding the device front with the other, place the device gently in the rack.
-
Page 6: Grounding The Device
Figure 6 Installing the device in the rack Grounding the device WARNING! • Correctly connecting the grounding cable is crucial to lightning protection and EMI protection. • Connect the grounding cable to the grounding system in the equipment room. Do not connect it to a fire main or lightning rod. -
Page 7: Grounding The Device By Using A Grounding Point On The Rack
Figure 7 Grounding the device by using a grounding strip Grounding the device by using a grounding point on the rack CAUTION: To ground the device by using a grounding point on the rack, make sure the rack is reliably grounded. -
Page 8: Grounding The Device By Using A Grounding Conductor Buried In The Earth
Figure 8 Grounding the device by using a grounding point the rack Grounding the device by using a grounding conductor buried in the earth If earth is available at the installation site, hammer a 0.5 m (1.64 ft) or longer angle iron or steel tube into the earth to serve as a grounding conductor. -
Page 9: (Optional) Installing Network Port Lightning Protectors
(Optional) Installing network port lightning protectors IMPORTANT: • Before installing a network port lightning protector, read the instructions in the document that comes with the protector. • Network port lightning protectors are available only for 10M/100M/1000M RJ-45 Ethernet copper ports. •... -
Page 10: (Optional) Installing A Surge Protected Power Strip
Figure 10 Installing a lightning protector for a network port (Optional) Installing a surge protected power strip IMPORTANT: Before installing a surge protected power strip, read the instructions in the document that comes with the strip. If you use an AC power line routed from outdoors for the device, use a surge protected power strip for the device to protect against damages caused by lightning strikes. -
Page 11: Connecting Ethernet Cables
• Stop bits—1. • Parity—None. • Flow control—None. Connecting Ethernet cables Connecting an Ethernet copper port Connect one end of the Ethernet cable to an Ethernet copper port on the device, and the other end to an Ethernet port on the peer device. After powering on the device, examine the LEDs of the fixed copper Ethernet port. -
Page 12: Installing A Power Module
Figure 11 Connecting an optical fiber Installing a power module The device supports only AC power modules. To install a power module: Remove the blank filler panel (if any) from the slot where you want to install a power module with a Phillips screwdriver. -
Page 13: Connecting A Power Cord
Connecting a power cord CAUTION: Before powering on the device, make sure the device is reliably grounded. After you connect a power cord for the device, examine the power module status LED to verify that the power module is operating correctly. For the power module LED description, see "Appendix B LEDs."... - Page 14 Press Ctrl+T to start heavy memory test Booting Normal Extended BootWare The Extended BootWare is self-decompressing..Done. **************************************************************************** H3C WX3840H BootWare, Version 5.12 **************************************************************************** Copyright (c) 2004-2018 New H3C Technologies Co., Ltd. Compiled Date : Jan 15 2018 CPU Type : XLP432 CPU Clock Speed...
- Page 15 Line con0 is available. Press ENTER to get started. Press Enter at the prompt, and you can configure the device when the prompt <H3C> appears. NOTE: The CPLD version is automatically upgraded to the latest version during the start-up process.
Need help?
Do you have a question about the WX3800H Series and is the answer not in the manual?
Questions and answers