Table of Contents
Advertisement
Quick Links
Contents
2 Installing the device ····································································· 2-1
Installation prerequisites ··········································································································· 2-1
Installation flowchart ················································································································ 2-1
Mounting the device on a workbench ·························································································· 2-2
Mounting the device in a 19-inch rack ·························································································· 2-3
Connecting the grounding cable ································································································· 2-5
Attaching the ring terminal to a grounding cable ······································································ 2-5
Connecting the grounding cable ·························································································· 2-5
(Optional) Installing network port lightning protectors ······································································ 2-8
(Optional) Installing a surge protected power strip ·········································································· 2-9
Connecting interface cables ······································································································ 2-9
Connecting the console cable and setting terminal parameters ·················································· 2-9
Connecting Ethernet cables ······························································································ 2-10
Connecting the power cord ····································································································· 2-11
Connecting the power adapter for the WX1804H-PWR/WX1820H access controller ····················· 2-11
Connecting the AC power cord for the WX1810H-PWR/WX1840H access controller ···················· 2-12
Verifying the installation ·········································································································· 2-12
Starting the device ················································································································ 2-13
i
Advertisement
Table of Contents
Related Manuals for H3C WX1804H-PWR
Summary of Contents for H3C WX1804H-PWR
-
Page 1: Table Of Contents
Connecting Ethernet cables ······························································································ 2-10 Connecting the power cord ····································································································· 2-11 Connecting the power adapter for the WX1804H-PWR/WX1820H access controller ····················· 2-11 Connecting the AC power cord for the WX1810H-PWR/WX1840H access controller ···················· 2-12 Verifying the installation ·········································································································· 2-12 ... -
Page 2: Installing The Device
Installing the device IMPORTANT: Keep the tamper-proof seal on a mounting screw on the chassis cover intact, and if you want to open the chassis, contact H3C for permission. Otherwise, H3C shall not be liable for any consequence. Installation prerequisites •... -
Page 3: Mounting The Device On A Workbench
Figure2-2 Installation flowchart for the WX1810H-PWR/WX1840H access controller Mounting the device on a workbench CAUTION: • To avoid damaging the device and affecting heat dissipation, do not place heavy objects on the device. • Make sure the workbench is anti-static. -
Page 4: Mounting The Device In A 19-Inch Rack
The workbench-mounting procedure is similar for WX1800H series access controllers. The following procedure uses the WX1804H-PWR access controller as an example. To mount the device on an anti-static workbench: Place the device upside down on the workbench. Use a cloth to clean the recessed areas on the bottom. - Page 5 Use the M4 screws supplied with the mounting brackets to attach the mounting brackets to both sides of the device. Figure2-5 Attaching the mounting brackets to the device Supporting the bottom of the device with one hand and holding the front of the device with the other, put the device in the rack.
-
Page 6: Connecting The Grounding Cable
Attaching the ring terminal to a grounding cable No grounding cable is provided with the WX1804H-PWR or WX1820H access controller. You need to purchase a grounding cable and attach the ring terminal provided with the access controller to the grounding cable. - Page 7 b. Use the grounding screw to attach the ring terminal of the grounding cable to the grounding hole and fasten the screw. Connect the other end of the grounding cable to the grounding strip. Make sure the grounding strip is reliably grounded. Figure2-8 Grounding the device by using a grounding strip Grounding the device by using a grounding point on the rack CAUTION:...
- Page 8 Figure2-9 Grounding the device by using a grounding point the rack Grounding the device by using a grounding conductor buried in the earth The WX1800H series access controllers use the same procedure for grounding by using a grounding conductor buried in the earth. The following uses the WX1840H access controller as an example. If earth is available at the installation site, hammer a 0.5 m (1.64 ft) or longer angle iron or steel tube into the earth to serve as a grounding conductor.
-
Page 9: (Optional) Installing Network Port Lightning Protectors
(Optional) Installing network port lightning protectors IMPORTANT: • Before installing a network port lightning protector, read the instructions in the document that comes with the protector. • Network port lightning protectors are available only for 10M/100M/1000M RJ-45 Ethernet copper ports. •... -
Page 10: (Optional) Installing A Surge Protected Power Strip
Figure2-11 Installing a lightning protector for a network port (Optional) Installing a surge protected power strip IMPORTANT: Before installing a surge protected power strip, read the instructions in the document that comes with the strip. If you use an AC power line routed from outdoors for the device, use a surge protected power strip for the device to protect against damages caused by lightning strikes. -
Page 11: Connecting Ethernet Cables
The following are the required terminal settings: • Bits per second—9600. • Data bits—8. • Stop bits—1. • Parity—None. • Flow control—None. Connecting Ethernet cables Connecting an Ethernet copper port Connect one end of the Ethernet cable to an Ethernet copper port on the device, and the other end to an Ethernet port on the peer device. -
Page 12: Connecting The Power Cord
Connecting the power adapter for the WX1804H-PWR/WX1820H access controller If you use the local power source for the WX1804H-PWR/WX1820H access controller, use a power adapter to connect the device to the power source. To connect the power adapter for the WX1804H-PWR/WX1820H access controller: Make sure the device is reliably grounded. -
Page 13: Connecting The Ac Power Cord For The Wx1810H-Pwr/Wx1840H Access Controller
Figure2-13 Connecting the power adapter for the WX1804H-PWR access controller Connecting the AC power cord for the WX1810H-PWR/WX1840H access controller Make sure the device is reliably grounded. Connect one end of the AC power cord to the AC power receptacle on the device. -
Page 14: Starting The Device
Starting the device The following procedure uses the WX1804H-PWR access controller as an example. To start the device: Power on the device. The device initializes its memory and runs the BootWare image. The following information appears on the terminal screen: System is starting... - Page 15 Press Enter at the prompt, and you can configure the device when the prompt <H3C> appears. NOTE: The CPLD version is automatically upgraded during the start-up process. 2-14...
Need help?
Do you have a question about the WX1804H-PWR and is the answer not in the manual?
Questions and answers