1. Manuals
  2. Brands
  3. tams elektronik Manuals
  4. Automobile Accessories
  5. FCS Series
  6. Manual

tams elektronik FCS Series Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
FCS-Module
Item no. 54-01016
Emergency vehicle light
Item no. 54-01026
Vehicle module
Item no. 54-01036
Item no. 54-01046
Emergency vehicle module
Item no. 54-01096
Lighting module
tams elektronik
FCS-1
FCS-2
FCS-3
Bus module
FCS-4
FCS-L
Manual
n n n

Advertisement

Table of Contents
loading

Related Manuals for tams elektronik FCS Series

Summary of Contents for tams elektronik FCS Series

  • Page 1 Manual FCS-Module FCS-1 Item no. 54-01016 Emergency vehicle light FCS-2 Item no. 54-01026 Vehicle module FCS-3 Item no. 54-01036 Bus module FCS-4 Item no. 54-01046 Emergency vehicle module FCS-L Item no. 54-01096 Lighting module tams elektronik n n n...
  • Page 2 English FCS modules © 10/2017 Tams Elektronik GmbH All rights reserved. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, without prior permission in writing from Tams Elektronik GmbH.

  • Page 3: Table Of Contents

    FCS modules English Table of contents 1. Getting started................4 2. Safety instructions...............6 3. Safe and correct soldering............9 4. Operation overview..............10 4.1. Voltage supply..............10 4.2. Possible connections............10 4.3. Modes of operation............13 5. Technical specifications..............15 5.1. FCS-1 to FCS-4..............15 5.2. FCS-L................16 6. Special features of the additional components......17 7.

  • Page 4: Getting Started

    English FCS modules 1. Getting started This manual applies to the following FCS modules compatible to the Faller** Car System, so for:  FCS-1 "Emergency vehicle light"  FCS-2 "Vehicle module"  FCS-3 "Bus module"  FCS-4 "Emergency vehicle module" ...
  • Page 5 FCS modules English Checking the package contents Please make sure that your package contains: Module Additional components manual* FCS-1 FCS-2 resistors 10 W resistor 10 kW light sensitive resistor diode 1N4148 transistor BC 327 reed contact dim switch DS-1 FCS-3 resistor 10 kW diode 1N4148 transistor BC 327...

  • Page 6: Safety Instructions

    English FCS modules  electronic tin solder (0.5 mm diameter)  connecting wire, e.g. enamelled copper wire  LEDs for the vehicle´s lighting. Depending on the vehicle´s size and construction you can use for example the following: SMD LEDs type 0402, 0603, 0805 oder 1206 or wired LEDs 1,8 mm ...
  • Page 7 FCS modules English  Connect transformers and soldering irons only in approved mains sockets installed by an authorised electrician.  Observe cable diameter requirements.  After condensation build up, allow a minimum of 2 hours for dispersion.  Use only original spare parts if you have to repair the kit or the ready-built module.
  • Page 8 English FCS modules Other dangers Children can cause any of the accidents mentioned above because they are inattentive and not responsible enough. Children under the age of 14 should not be allowed to work with this kit or the ready-built module.

  • Page 9: Safe And Correct Soldering

    FCS modules English 3. Safe and correct soldering Caution: Incorrect soldering can cause dangers through fires and heat. Avoid these dangers by reading and following the directions given in the chapter Safety instructions.  Use a small soldering iron with max. 30 Watt. Keep the soldering tip clean so the heat of the soldering iron is applied to the solder point effectively.

  • Page 10: Operation Overview

    English FCS modules 4. Operation overview The modules are particularly designed for the use in vehicles compatible to the Faller** car system. The modules FCS-1 to FCS-4 are used in vehicles run with two accumulator batteries, the module FCS-L in vehicles with one accumulator battery or, when reducing the module´s input voltage, in vehicles run with two accumulator batteries, as well.
  • Page 11 FCS modules English FCS-1 FCS-2 FCS-3 FCS-4 FCS-L Front lights (white LEDs) Back lights (red LEDs) Brake lights Dim switch DS-1 Flashing lights + (5) + (2) (blue or orange LEDs) Warning lights (yellow LEDs) Siren (loudspeaker) Motor / acceleration delay Motor / braking delay ...
  • Page 12 English FCS modules Dim switch (FCS-2 only) Depending on the ambient lighting, the lighting of the vehicle is switched on and off via a light sensitive switch. The sensitivity of the switch is set via a trimpot. Flashing lights (FCS-1 and FCS-4) The FCS-1 has 5 outputs, the FCS-4 two outputs for the connection of orange or blue LEDs as flashing lights.

  • Page 13: Modes Of Operation

    FCS modules English 4.3. Modes of operation FCS-1 "Emergency vehicle light" According to the connection of the circuit´s input, the LEDs connected to the five outputs are controlled by two different programmes: Programme 1 "Double flashlight": The LEDs flash twice each and then go out for a short time.
  • Page 14 English FCS modules FCS-4 "Emergency vehicle module" While the vehicle is in motion the flashing lights double flash and the siren is in operation with short breaks. When crossing a stop the back lights are switched brighter for a short time as braking lights and the siren is switched off (provided the reed contact which is in the vehicle is connected to the module).

  • Page 15: Technical Specifications

    FCS modules English 5. Technical specifications 5.1. FCS-1 to FCS-4 Supply voltage 2 - 3 Volt d.c. voltage Current consumption (without connected loads) approx. 2 mA Max. total current 40 mA Total number of outputs max. 6 (depending on the version) Max.

  • Page 16: Fcs-L

    English FCS modules 5.2. FCS-L Supply voltage - vehicles with one battery 0,9 – 1,8 Volt d.c. voltage - vehicles with two batteries 1,6 – 2,5 Volt d.c. voltage Current consumption ca. 25 mA (independent of the voltage applied) Total number of outputs Max.

  • Page 17: Special Features Of The Additional Components

    FCS modules English 6. Special features of the additional components Depending on the specification of the modules, different additional external components have to be connected. These have the following special features: Resistors Resistors reduce current. Their mounting orientation is of no importance.
  • Page 18 English FCS modules Diodes Diodes allow the current to pass through in one direction only (forward direction), simultaneously the voltage is reduced by 0,3 to 0,8 V. Exceeding of the limit voltage always will destroy the diode, and allow current to flow in the reverse direction.
  • Page 19 FCS modules English Transistors Transistors are current amplifiers which convert low signals into stronger ones. There are several types in different package forms available. The type designation is printed on the component. Transistors for a low power rating (e.g. BC types) have a package in form of a half zylinder (SOT-package).

  • Page 20: Mounting

    English FCS modules 7. Mounting 7.1. Mounting the FCS-1 Open housing vehicle. Locate the position for the module.. Connections FCS-1 Connection to the supply voltage "-" of the batteries "+" of the batteries Caution: The module should not be connected the wrong way round.
  • Page 21 FCS modules English Connection of the LEDs for the flashlights Connect the anodes (+) of the LEDs to the soldering points X4 to X8 and the cathodes (-) to the soldering point X3. Note the different functions of the outputs. Additional series resistors are not necessary for the operation of the LEDs for the flashlights.
  • Page 22 English FCS modules Connection of the LEDs for the front light You may connect up to two white LEDs for the front lighting to the module. LED6* | LED7* White LEDs for front lighting R6* | R7* Series resistors for LED6 and LED7 Voltage output (-) of the circuit * Not supplied.

  • Page 23: Mounting The Fcs-2

    FCS modules English 7.2. Mounting the FCS-2 Open the housing vehicle. Locate the position module. Disconnect connections from accumulator batteries, the motor and the mounted reed contact except for the wire to the charging contact. Connections FCS-2 n many vehicles the resistor R7 shown in the connection diagram is mounted into the lead-in wire to the motor.
  • Page 24 English FCS modules "-" of the batteries "+" of the batteries Voltage output (-) of the circuit Front lighting (LED1 and LED2) Light sensitive switch Braking / reversing lights (LED3 and LED4) Motor control Existing reed contact Secondary reed contact External Components D2 (1N4148) Additional diode...
  • Page 25 FCS modules English Connection to the supply voltage Connect the connecting point X2 to the plus pole of the accumulator batteries and the minus pole of the accumulator batteries to the existing switch S of the vehicle. Connect the second pole of the switch to the connecting point X1.
  • Page 26 English FCS modules Connection of the motor Connect the enclosed diode 1N4148 to the connections of the motor. Observe the polarity of the diode. Then connect the minus pole of the motor to the switch switching the minus pole of the accumulator batteries and to the connecting point X1.
  • Page 27 FCS modules English Setting the sensitivity of the light Before closing the housing of the vehicle, you should set the sensitivity of the dim switch to the desired lighting conditions. First set the trim pot to mid-position and change the sensitivity as far as necessary. The circuit requires 3 or 4 seconds to react.

  • Page 28: Mounting The Fcs-3

    English FCS modules 7.3. Mounting the FCS-3 Open the housing of the vehicle. Locate the position for the module. Disconnect all connections from the accumulator batteries, the motor and the mounted reed contact except for the wire to the charging contact.
  • Page 29 FCS modules English "-" of the batteries "+" of the batteries / LED1 and LED4 Voltage output (-) of the circuit Motor control Right indicator (LED3 and LED4) Braking / reversing lights (LED5 and LED6) Left indicator (LED7 and LED8) Existing reed contact Additional reed contact External Components...
  • Page 30 English FCS modules Connection to the supply voltage Connect the connecting point X2 to the plus pole of the accumulator batteries and the minus pole of the accumulator batteries to the existing switch S of the vehicle. Connect the second pole of the switch to the connecting point X1.
  • Page 31 FCS modules English Connection of the motor Connect the enclosed diode 1N4148 to the connections of the motor. Observe the polarity of the diode. Then connect the minus pole of the motor to the switch switching the minus pole of the accumulator batteries and to the connecting point X1.
  • Page 32 English FCS modules Connection of the LEDs for the front light You may connect up to two white LEDs for the front lighting to the voltage output of the module. These LEDs are not controlled by the stored software. They light as soon as the module is connected to the power supply.

  • Page 33: Mounting The Fcs-4

    FCS modules English 7.4. Mounting the FCS-4 Open the housing of the vehicle. Locate the position for the module. Disconnect all connections from the accumulator batteries, the motor and the mounted reed contact except for the wire to the charging contact.
  • Page 34 English FCS modules "-" of the batteries "+" of the batteries / LED1 and LED2 Voltage output (-) of the circuit Flashing light 1 (LED3) Flashing light 2 (LED4) Siren Motor control Braking / reversing lights (LED5 and LED6) Existing reed contact External Components D2 (1N4148) Additional diode...
  • Page 35 FCS modules English Connection to the supply voltage Connect the connecting point X2 to the plus pole of the accumulator batteries and the minus pole of the accumulator batteries to the existing switch S of the vehicle. Connect the second pole of the switch to the connecting point X1.
  • Page 36 English FCS modules Connection of the LEDs for the flashing lights Connect the anodes (+) of the two LEDs for the flashing lights to the connecting points X4 and X5. Connect the cathodes (-) of the LEDs both to the connecting point X3. Additional series resistors are not necessary for the operation of the LEDs for the flashing lights.
  • Page 37 FCS modules English Connection of the diodes for the front light You may connect up to two white LEDs for the front lighting to the voltage output of the module. These LEDs are not controlled by the stored software. They light as soon as the module is connected to the power supply.

  • Page 38: Mounting The Fcs-L

    English FCS modules 7.5. Mounting the FCS-L Open the housing of the vehicle. Locate the position for the module. Connections FCS-L D1, D2 LED, white (not supplied) D3, D4 LED, red (not supplied) if required, e.g. diode 1N4148 connection to "+" of the accumulator batteries connection to "-"...
  • Page 39 FCS modules English Connection to the supply voltage The module is designed for connecting to a supply voltage of 0,9 to 1,8 V (= one accumulator battery). If it is connected to a higher supply voltage of 1,6 bis 2,5 V (= two accumulator batteries) you have to reduce the input voltage by mounting a diode (e.g.

  • Page 40: Check List For Troubleshooting

    English FCS modules 8. Check list for troubleshooting  Parts are getting very hot and/or start to smoke. Disconnect the system from the mains immediately! Possible cause: The connections to the power supply are connected the wrong round. à Check the connection. In this case the module is probably damaged irreparably.
  • Page 41 FCS modules English  FCS-4: The siren does not work. Possible cause: The connections of the transistor are reversed. à Check the connections. Possible cause: The power supply is interrupted. à Check the connections. Possible cause: The vehicle halts at a stop. This is no a fault. The siren is switched off while the vehicle is halting.

  • Page 42: Guarantee Bond

    English FCS modules 9. Guarantee bond For this product we issue voluntarily a guarantee of 2 years from the date of purchase by the first customer, but in maximum 3 years after the end of series production. The first customer is the consumer first purchasing the product from us, a dealer or another natural or juristic person reselling or mounting the product on the basis of self- employment.

  • Page 43: Eu Declaration Of Conformity

    FCS modules English 10. EU declaration of conformity This product conforms with the EC-directives mentioned below and is therefore CE certified. 2004/108/EG on electromagnetic. Underlying standards: EN 55014-1 and EN 61000-6-3. To guarantee the electromagnetic tolerance in operation you must take the following precautions: ...
  • Page 44 Information and tips: http://www.tams-online.de Warranty and service: Tams Elektronik GmbH Fuhrberger Straße 4 DE-30625 Hannover fon: +49 (0)511 / 55 60 60 fax: +49 (0)511 / 55 61 61 e-mail: modellbahn@tams-online.de...

This manual is also suitable for:

Fcs-1Fcs-2Fcs-3Fcs-4Fcs-l54-01016 ... Show all

Table of Contents