Advertisement
Quick Links
Read all instructions before assembling crib.
Save instructions for future use.
Adult assembly required.
Small parts may present choking hazard prior to assembly.
Enclosed please find simple step-by-step instructions to help
you quickly assemble your products.Before you begin we
recommend that you following the steps below:
1.Please read the instructions thoroughly.
2. Identify all parts and hardwares
3.You will need the following tools:
Philips head screw driver
Flat head screw driver Hammer
Do Not Use Power Drills or Drivers
To protect your parts during assembly please place them on a
soft surface.
To clean surface use only water on a damp cloth. Do not use
window cleaners or cleaning abrasives as it will scratch the
surface and could damage the protective coating.
Please note that the warning sticker is placed on the cribs to keep parents and
caregivers informed it is a requirement by law under CPSC And ASTM.
We do apologize for any inconvenience this may cause you.
STYLE NO: 663
1
DREAM ON ME INC.
125 HELEN STREET
S.PLAINFIELD NJ 07080
908-791-0555
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Dream On Me Crib 663
Summary of Contents for Dream On Me Crib 663
- Page 1 DREAM ON ME INC. 125 HELEN STREET STYLE NO: 663 S.PLAINFIELD NJ 07080 908-791-0555 Read all instructions before assembling crib. Save instructions for future use. Adult assembly required. Small parts may present choking hazard prior to assembly. Enclosed please find simple step-by-step instructions to help you quickly assemble your products.Before you begin we...
- Page 2 PARTS OR SHARP EDGES BEFORE AND AFTER ASSEMBLY.A FREQUENT CHECK SHOULD BE MADE DURING USE.DO NOT USE CRIB IF ANY PARTS ARE MISSING, DAMAGED OR BROKEN.CONTACT DREAM ON ME INC.125 HELEN STREET S.PLAINFIELD NJ 07080 FOR REPLACEMENT PARTS AND INSTRUCTIONAL LITERATURE IF NEEDED.DO NOT SUBSTITUTE PARTS.
-
Page 3: Connection Hardware
CONNECTION HARDWARE d:3” Allen head bolt (4pcs) a: 1-5/8” Allen head b:Wood dowels (12pcs) c:Allen wrench (1pc) bolt (18 pcs) e:Barrel nuts (14 pcs) f: 3/4” Allen head bolt (4 pcs) g: 2-1/5” Allen head bolt (10 pcs) h:1-1/5” Screw (3 pcs) m:Belt (1pc) k:Washer (2pcs) j:Shelf support (8pcs) - Page 4 Changer front bar I:Changing surface (1pc) K:Changer bottom shelf (1pc) J:Changer middle panel F: T op (1pc) G: Middle (1pc) H:Bottom (1pc) M:Left back leg (1pc) P:Back top rail(1pcs) L:Changer left side (1pc) N:Left board (1pc) O:Left front leg (1pc) Q:Back rail bottom (1pc) R:Metal spring support platform (1pc) S:Front rail bottom (1pc)
- Page 5 CRIB ASSEMBLY STEP 1 Attach The changer back(B&C) , and The changer middle(D&E) , and The changer front (F,G,&H) toThe changer right side (A) using wood dowels (b), bolts (a),bolts (g) and barrel nuts(e) by allen wrench (c) . Model shown is example only. Styles may vary .
- Page 6 STEP 3 Attach The changer back (B&C) and The changer middle (D&E) and The changer front (F,G&H) to The changer left side (L) using wood dowels (b),bolts (a) and bolts (q) by allen wrench (c) . Model shown is example only. Styles may vary .
- Page 7 STEP 5 Attach The top rail (P) and the bottom rail (Q) to The changer side (L) and left headboard using wood dowels(b),bolts(q&g) and barrel nuts(e) by allen wrench. Model shown is example only. Styles may vary . STEP 6 Locate the mattress support (R) with tabs .
- Page 8 STEP 7 Attach The bottom front rail (S) to The changer side (L) and the left head board using bolts (g),barrel nuts (e) and allen wrench (c) . Model shown is example only. Styles may vary . STEP 8 Attach left side panel (U) & right side panel (V) to back panel (W) by inserting cross screw (p) into the holes on left side panel (U) &...
- Page 9 STEP 9 Slide the bottom panel (X) painted side up , into grooves of the left side panel (U) and the right side panel (V) . In the end , insert the bottom (X) into the groove of back panel (W) . Model shown is example only.
- Page 10 STEP 11 Insert the shelf supports (j) in the holes in the posts of changing table. Then place the changer middle shelf (Y) inside the shelf support. Tighten the screws in the shelf supports (j) . Model shown is example only. PHILLIPS-- HEAD SCREWDRIVER REQUIRED Styles may vary .
- Page 11 STEP 12 1.Slide the drawers into rails on head board (A&L) . 2.Assembly the belt (m) to the changer side (A&L) using washer(k) and bolt(l). 3.Add the pad (Z) . 4.Put the child on the pad,then insert safty restraint system of the tape across child's waist. The tightness can be adjusted by increasing the tension of the tape.
- Page 12 Converting crib to a toddler bed You have the option to convert crib to a toddler bed 1:Remove the front rail (S) ; 2:Install the mattress support (R) in its lowest position . 3:Assemble the guard rail (α) to the left front leg (O) and changer left side (L) by bolts (g) used on front rail and allen wrench(c).
- Page 13 Converting crib to a day bed You have the option to convert crib to a day bed 1:Remove the front rail bottom(S) 2:Install the mattress support (R) in its lowest position. Model shown is example only. Styles may vary . Converting crib to a full size bed I Converting kit is sold separately You have the option to convert...
- Page 14 Converting crib to a full size bed II LEFT FOOT PLATFORM RIGHT FOOT PLATFORM RAIL POST x 1 POST x 1 POST x 1 NOT INCLUDED NOT INCLUDED NOT INCLUDED Converting kit is sold separately You have the option to convert crib to a full size bed II 1:Use the back rail as the headboard of full size bed.
- Page 15 FURNITURE TIPPING DETERRENT HARDWARE HOW TO LOCK Tipping furniture may injure young children. Use of this tipping restraint hardware is highly recommended. When properly instated this hardware could provide protection against the unexpected tipping of furniture due to improper use. WARNING This hardware is only a deterrent.Adult supervision is the only proper deterrent to prevent improper use of any potentially hazardous product.
Need help?
Do you have a question about the Crib 663 and is the answer not in the manual?
Questions and answers