Advertisement
Quick Links
Dream On Me Inc.
1532 S WASHINGTON AVE
PISCATAWAY TWP NJ 08854
OFFICE: 732-752-7220
CUSTOMER SERVICE: 732-366-1788
Read all instructions before assembling crib.
Save instructions for future referrence.
Adult assembly required.
Small parts may present choking hazard prior to assembly.
Enclosed are step by step instructions to help you.
quickly assemble your product.Before you begin we recommend
that you follow the steps below:
1. Please read the instructions thoroughly.
2. Identify all parts and hardware.
3. You will need the following tools:
Philips head screw driver
Flat head screw driver Hammer
Do Not Use Power Drills or Drivers
parts during assembly please place them on a soft
To protect
To clean surface use only water on a damp cloth. Do not use
window cleaners or cleaning abrasives as it will scratch the surface
and could damage the protective coating.
ASSEMBLY INSTRUCTIONS
ITEM NO: 656
s
1
surface.
Advertisement
Related Manuals for Dream On Me 656
Summary of Contents for Dream On Me 656
- Page 1 Dream On Me Inc. ASSEMBLY INSTRUCTIONS 1532 S WASHINGTON AVE ITEM NO: 656 PISCATAWAY TWP NJ 08854 OFFICE: 732-752-7220 CUSTOMER SERVICE: 732-366-1788 Read all instructions before assembling crib. Save instructions for future referrence. Adult assembly required. Small parts may present choking hazard prior to assembly.
- Page 3 . Never use this product if there are any loose or missing fasteners, loose joints,broken parts, or torn mesh/fabric. check before assembly and periodically during use. Contact DREAM ON ME for replacement parts and instructional literature if needed. . Never substitute parts, the product including side rails, must be fully erected prior to use.
-
Page 5: Connection Hardware
CONNECTION HARDWARE Allen head bolt (3 pcs) a: 2” b: 1-3/8”Allen head bolt (20 pcs) c: 2-3/8”Allen head bolt (6 pcs) e:Barrel nuts (12 pcs) d:3-1/2”Allen head bolt (6 pcs) f:Wood dowels (20pcs) k: 3/4” Allen head bolt j:Shelf support (4pcs) h:1-3/8”... - Page 6 Changer shelf Changer bar Changer middle panel E1:Bar (5pcs) D1:Top bar (1pc) D2: Panel (1pc) D3:Bottom bar (1pc) E2:Middle bar (2pcs) F1:Changing surface (1pc) F2:Changer middle shelf (1pc) F3:Changer bottom shelf (1pc) E3:Back bottom bar (1pc) Drawer Back rail (1pc) G1:Front panel (3pcs) G2:Left side panel (3pcs) G3: Right side panel (3pcs)
- Page 7 CRIB ASSEMBLY STEP 1 Attach The changer bar(E1&E2&E3) , and The changer middle(D1&D3) toThe changer side (B2) using wood dowels (f),bolts(b) and allen wrench (q). Model shown is example only. Styles may vary . STEP 2 Lay down the assembled parts on the floor .
- Page 8 STEP 3 Attach The changer bar (E1&E2&E3) and The changer middle (D1&D3) to The changer side (B1) using wood dowels (f),bolts (b) and allen wrench (q) . j x4 Model shown is example only. Styles may vary . Insert the shelf supports (j) in the holes in the posts of changing table. Then place the changer middle shelf (F2) inside the shelf support .
- Page 9 Connect the assembled parts of STEP 5 STEP 4 to the assembled parts of STEP 3 by using bolt (a) and allen wrench (q). Connect the assembled parts to left board (A2) by using bolt (c), barrel nuts (e) and allen wrench (q). Attach the left front leg (A3) to the left board (A2) using bolt (d), barrel nuts (e) and allen wrench (q).
- Page 10 Attach The front rail (J) to STEP 7 The changer side (B1) and The left front leg (A3) using bolts (c),barrel nuts (e) and allen wrench (q) . Model shown is example only. Styles may vary . STEP 8 Attach left side panel (G2) & right side panel (G3) to back panel (G4) by inserting cross screw (g) into the holes on left side panel (G2) &...
- Page 11 STEP 9 Slide the bottom panel (G5) painted side up , into grooves of the left side panel (G2) and the right side panel (G3) . In the end , insert the bottom (G5) into the groove of back panel (G4) . Model shown is example only.
- Page 12 STEP 11 1.Slide the drawers into rails on head board (B1&B2) . 2.Assembly the belt (n) to the changer side (B1& B2) using washer (l) and bolt (m) . Note:please assemble the longer belt to the far side from the crib. 3.Add the pad (L) .
- Page 13 Converting crib to a toddler bed Please note that the warning sticker is placed on the cribs to keep parents and caregivers informed it is a requirement by law under CPSC And ASTM. We do apologize for any inconvenience this may cause you. Model shown is example only.
- Page 15 Converting crib to a day bed You have the option to convert crib to a day bed 1:Remove the front rail (J). 2:Install the mattress support (K) in its lowest position. 3:Assembly the bottom bar (M) to left front leg (A3) and changer side (B1) using allen head bolt (c) and barrel nuts (e) as is shown .
- Page 16 Converting crib to a full size bed II (Hollywood bed frame sold separately) PARTS REQUIRED TO COMPLETE STEP LEFT FOOT PLATFORM RIGHT FOOT PLATFORM RAIL POST x 1 POST x 1 POST x 1 NOT INCLUDED NOT INCLUDED NOT INCLUDED You have the option to convert crib to a full size bed II 1:Use the back rail as the headboard of full size bed.
- Page 17 FURNITURE TIPPING DETERRENT HARDWARE HOW TO LOCK Tipping furniture may injure young children. Use of this tipping restraint hardware is highly recommended. When properly instated this hardware could provide protection against the unexpected tipping of furniture due to improper use. WARNING This hardware is only a deterrent.Adult supervision is the only proper deterrent to prevent improper use of any potentially hazardous product.
-
Page 19: Limited Warranty
LIMITED WARRANTY Dream on Me warrants its product to be free from defects in material and workmanship and agrees to remedy any such defect. This warranty covers 30 days from the date of original purchase. This warranty is valid only upon presentation of proof of purchase.
Need help?
Do you have a question about the 656 and is the answer not in the manual?
Questions and answers