Download
Share
Print this page
Ricoh Martini-P1 Technical Bulletin
  1. Manuals
  2. Brands
  3. Ricoh Manuals
  4. Printer
  5. Martini-P1
  6. Technical bulletin
Ricoh Martini-P1 Technical Bulletin

Ricoh Martini-P1 Technical Bulletin

Hide thumbs

Advertisement

Quick Links

Download this manual
Reissued: 8-Apr-05
Model:
Martini-P1
RTB Correction
The items in bold italics have been corrected or added.
Subject:
MT-P1 Service Manual
From:
2nd Tech Support Sec. Service Support Dept.
Classification:
Troubleshooting
Mechanical
Paper path
Product Safety
AN OVERVIEW OF THE SERVICE MANUAL DIFFERENCES
A Service Manual will not be released for the MT-P1 (G126), so refer to this RTB and
the MT-C1/C2 Service Manual for the differences.
The areas that are
Some details are shown in other RTB/MBs.
e.g. The Installation Procedure differences are shown in RTB RG126002.
Note: MT-P1 mass production begins from March 2005.
T
echnical
BETWEEN THE MT-P1 AND MT-C1/C2
highlighted in blue
are unique to the MT-P1.
B
ulletin
Date:
2-Mar-05
Prepared by:
Part information
Electrical
Transmit/receive
Other (
)
PAGE: 1/7
No.:
RG126001a
S. Watanabe
Action required
Service manual revision
Retrofit information

Advertisement

loading
Need help?

Need help?

Do you have a question about the Martini-P1 and is the answer not in the manual?

Questions and answers

Related Manuals for Ricoh Martini-P1

Summary of Contents for Ricoh Martini-P1

  • Page 1 PAGE: 1/7 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126001a RTB Correction The items in bold italics have been corrected or added. Subject: Prepared by: MT-P1 Service Manual S. Watanabe From: 2nd Tech Support Sec. Service Support Dept.
  • Page 2 PAGE: 2/7 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126001a 1. INSTALLTION PROCEDURE See RTB RG126002. 2. PREVENTATIVE MAINTENANCE PM procedures: Same with all three models. PM parts: No unique parts for the P1 (see table below). Unique/Common...
  • Page 3 PAGE: 3/7 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126001a Part Q'ty/ Unique or Description Number Unit Interval Common Fusing unit AE045046 Cleaning WEB 300k Cleaning WEB Pressure AE040038 600k Roller Cleaning WEB Pressure 600k AE031026 Roller Bearing...
  • Page 4 PAGE: 4/7 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126001a 3. REPLACEMENT AND ADJUSTMENT Procedures: Same for all three models. Components: (See the table below). Components Note EXTERIOR Upper Cover Unique to this model Call Light Unique to this model...
  • Page 5 PAGE: 5/7 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126001a 4. TROUBLESHOOTING Same for all three models. 5. SP TABLES, ACCESS METHOD SP tables: Same for all three models. Access method: 5-1. To Enter SP Mode Press the “Up/Down” arrow keys together for about 5 seconds, and then press the “Enter”...
  • Page 6 PAGE: 6/7 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126001a 1. LCT LCIT RT43 (B473: Maui) 2. LG/B4 Option 81/2"x14" Paper Size Tray Type 1075 (B474) 3. Cover Interposer Cover Interposer Tray Type 1075 (B470) 4. 100-staple Finisher SR841 (B706: Victoria-D) 5.
  • Page 7 PAGE: 7/7 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126001a Print Paper Weight Paper Tray 52.3 ~ 127.9 g/m (14 ~ 34 lb.) Duplex 64 ~ 127.9 g/m (17 ~ 34 lb.) By-pass: Standard 52.3 ~ 157 g/m (14 ~ 43 lb.)
  • Page 8 PAGE: 1/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a RTB Reissue Two illustrations were corrected (pg. 10, pg. 65). Subject: Prepared by: MT-P1 Installation Procedure S. Watanabe From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting...
  • Page 9 PAGE: 2/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a INSTALLATION PROCEDURE Model MT-P1 (Machine Code: G126)
  • Page 10 PAGE: 3/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a IMPORTANT SAFETY NOTICES PREVENTION OF PHYSICAL INJURY 1. Before disassembling or assembling parts of the printer and peripherals, make sure that the power supply cord is unplugged. 2. The wall outlet should be near the machine and easily accessible.
  • Page 11 PAGE: 4/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a SAFETY AND ECOLOGICAL NOTES FOR DISPOSAL 1. Do not incinerate toner bottles or used toner. Toner dust may ignite suddenly when exposed to an open flame. 2. Dispose of used toner, developer, and organic photoconductors in accordance with local regulations.
  • Page 12 PAGE: 5/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a 1. Installation Requirements Operating Environment 1. Temperature Range: Recommended: 15°C to 25°C (59°F to 77°F) Possible: 10°C to 32°C (50°F to 90°F) 2. Humidity Range: 15% to 80% RH (27°C 80%, 32°C 54%) 3.
  • Page 13 PAGE: 6/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a 9. Place the printer on a strong and level base with the front and back of the machine within ±5 mm (0.2") of level. 10. Do not place the machine where it may be subjected to strong vibrations.
  • Page 14 PAGE: 7/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a Minimum Space Requirements Place the printer near the power source, providing minimum clearance as shown below. The same amount of clearance is necessary when optional peripheral devices are installed.
  • Page 15 PAGE: 8/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a Power Requirements CAUTION 1. Make sure that the wall outlet is near the main machine and easily accessible. Make sure the plug is firmly inserted in the outlet.
  • Page 16 PAGE: 9/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a 2. Main Machine (G126) Accessory Check Check the accessories and their quantities against this list: Description Q’ty 1. Model Name Decal ( -22 Only ) ..........1 2. Decal – Paper Size..............1 3.
  • Page 17 PAGE: 10/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a Installation Procedure Removing Tapes and Retainers CAUTION To avoid serious injury, do not connect the power plug to the machine until you are instructed to do so. G126I151.WMF 1.
  • Page 18 PAGE: 11/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a 6. Open the front door, open the toner bottle holder [C], then remove all tape and shipping retainers. B064I007.WMF 7. Remove the PCU inner cover [D] (2 screws) and disconnect the fan motor [E] (1 connector).
  • Page 19 PAGE: 12/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a 8. Lower the transfer unit by turning its knob [A]. 9. Remove the bracket [B], and the red tag from the transfer belt (1 screw). 10. Remove the pin [C], and the red tag from the cleaning plate.
  • Page 20 PAGE: 13/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a 11. Open the tandem tray (top paper tray) and remove the metal retainer bracket [D] (1 screw), wire, and red tag. B064I401.WMF...
  • Page 21 PAGE: 14/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a Removing and Filling the Development Unit IMPORTANT: Before you begin, remove the toner bottle if it is installed. Note: If the toner bottle is in the machine when you do this procedure, the toner bottle holder can be damaged.
  • Page 22 PAGE: 15/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a 6. Disconnect the development unit [F] (2 connectors). NOTE: If the LCT is installed, you may need to disconnect it so the front door can open far enough to allow removal of the development unit.
  • Page 23 PAGE: 16/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a Re-installing the Development Unit Push the development unit all the way to the right. Continue to hold the unit to the right and push it into the machine. IMPORTANT: Make sure the pin [A] goes into the left side of the hole in the development unit plate.
  • Page 24 PAGE: 17/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a Initializing the Drum Settings You must do SP2963 (Installation Mode) to 1) Initialize the developer and do a forced toner supply to the development unit, and 2) Initialize the auto process control settings.
  • Page 25 PAGE: 18/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a Tandem Tray Before shipping the machine, the tandem tray is set for A4 or LT LEF and must be adjusted if the customer wants to use the tandem tray for another paper size.
  • Page 26 PAGE: 19/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a 6. Remove the tray cover [A] (2 screws). 7. Remove the motor cover [B] (4 screws). B064I566.WMF 8. Re-position the side fences [C] (8 screws). The outer slot position is used when loading A4 size paper.
  • Page 27 PAGE: 20/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a Machine Level 1. Set a stand [A] at each corner of the machine. 2. Place a level on the exposure glass and use a wrench to turn each nut [B] and level the machine to ±5 mm of the horizontal.
  • Page 28 PAGE: 21/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a Call Light Setting 1. Do an accessory check. Check the accessories and their quantities against this list: Description Q’ty LED Stand ................... 1 LED Stand Front Cover ............... 1 LED Stand Rear Cover..............
  • Page 29 PAGE: 22/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a 5. Remove the right cap. 6. Attach the LED Stand (4 screws). 7. Connect one end of the long harness to the LED Stand Front Cover (CN592). CN592...
  • Page 30 PAGE: 23/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a 10. Attach the LED Stand Front Cover. 11. Attach the LED Stand Rear Cover (1 screw). LED Stand Rear Cover...
  • Page 31 PAGE: 24/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a 3. A3/DLT Feeder Kit (B475) Accessory Check Check the accessories and their quantities against this list: Description Q’ty 1. A3/DLT Tray ................1 2. Short connector ..............1 3.
  • Page 32 PAGE: 25/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a Installation Procedure CAUTION Switch the machine off and unplug the machine before starting the following procedure. 1. Draw out the tandem tray completely to separate the left and right sides of the tray, then remove the front cover [A] (2 screws).
  • Page 33 PAGE: 26/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a 4. Remove the right tandem tray [A] (2 screws). Save these screws. B475I709.WMF 5. Connect the short connector [B] to the left tandem tray terminal [C]. B475I201.WMF 6. Remove the stay [D] (2 screws) and re- install it.
  • Page 34 PAGE: 27/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a 4. LCT (B473) Accessory Check Check the accessories and their quantities against this list: Description Q’ty 1. Flat-head shoulder screw - M4 x 6 ........1 2. Upper docking pins (grooved) ..........2 3.
  • Page 35 PAGE: 28/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a Installation Procedure B473I001.WMF B473I002.WMF Removing Tape 1. Remove the filament tape from the body [A] and top cover [B] of the LCT. 2. Remove the tape under the lid [C] of the LCT.
  • Page 36 PAGE: 29/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a Preparing the Main Machine CAUTION Switch the machine off and unplug the machine before starting the following procedure. 1. Remove the LCT installation cover [A] from the right side of the machine.
  • Page 37 PAGE: 30/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a B473I005.WMF 2. Align the holes on the side of the LCT [A] with the docking pins on the side of the machine [B], then slowly push the LCT onto the pins.
  • Page 38 PAGE: 31/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a 5. LG/B4 Feeder Kit (B474) ACCESSORY CHECK Check the accessories and their quantities against this list: Description Q’ty 1. Tapping screws - M4 x 8 ............4 2. Tapping hex screws - M4 x 8..........6 3.
  • Page 39 PAGE: 32/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a Installation Procedure If the LCT is connected to the machine 1. Open the cover and remove the paper. 2. Lower the LCT tray. Cover the near end sensor [A], then press the tray down button [B] to lower the tray bottom plate.
  • Page 40 PAGE: 33/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a 5. Remove the LCT cover [A] (1 screw). 6. Remove the right stay [B] and re-attach it below (2 screws). 7. Remove the right cover [C] (2 screws).
  • Page 41 PAGE: 34/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a 13. Move the front side fence [A] to the LG position and fasten (1 screw). 14. Move the rear side fence [B] to the LG position and fasten (1 screw).
  • Page 42 PAGE: 35/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a 6. 3000-Sheet Finishers (B674) Accessory Check Check the accessories and their quantities against this list: Description Q’ty 1. Rear joint bracket ..............1 2. Front joint bracket..............1 3.
  • Page 43 PAGE: 36/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a Installation Procedure This section describes the common installation instructions for these finishers: • B674 Booklet Finisher, which can do punching, shifting, stapling, and saddle stitching with staples. B468I001.WMF Removing Tapes and Retainers 1.
  • Page 44 PAGE: 37/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a Installation CAUTION Switch the machine off and unplug the machine before starting the following procedure. B468I003.WMF 1. Install the front [A] and rear [B] joint brackets (2 screws each, M4x 14).
  • Page 45 PAGE: 38/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a B468I004.WMF 3. Peel the cover tape from the sponge cushion [A], then install it in the upper slot. NOTE: If you will also install the cover interposer tray, do not attach the cushion here.
  • Page 46 PAGE: 39/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a B674 B468I005.WMF 1. Install the lower output tray [A] (2 screws). NOTE: Only the lower output tray has a movable support tray [B]. 2. Install the upper output tray [C] (2 screws).
  • Page 47 PAGE: 40/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a Enabling Booklet Binding To enable booklet binding, you must select the ‘center stapling’ position. These SP adjustments are available but not required at installation. SP6902 Fold Position Use this SP to fine adjust the fold and staple positions if they Adjustment are not aligned correctly.
  • Page 48 PAGE: 41/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a 7. Punch Unit (B377) The Punch Unit B377 is installed in the 3000-Sheet Finishers B674. Accessory Check Check the accessories and their quantities against this list: Description Q’ty 1.
  • Page 49 PAGE: 42/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a B377I201.WMF B377I103.WMF B377I202.WMF Installation Procedure CAUTION Switch off the main machine and unplug its power cord. 1. If the finisher is connected to the machine, disconnect it. 2. Unpack the punch unit and remove all tapes and shipping retainers.
  • Page 50 PAGE: 43/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a B377I203.WMF B377I105.WMF B377I106.WMF 8. Remove the shipping bracket [A] (2 screws). 9. Position the 2 mm spacer [B] and secure the punch unit (2 screws). 10. Secure the punch unit at the front with the shoulder screw [C] (1 screw).
  • Page 51 PAGE: 44/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a 8. Cover Interposer Tray (B470) Accessory Check Check the accessories and their quantities against this list: B470I006.WMF Description Q’ty 1. Front door extension (Top) ............ 1 2. Rear cover extension (bottom) ..........1 3.
  • Page 52 PAGE: 45/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a Installation Procedure This procedure shows you how to install the Cover Interposer Tray B470 on the: • 3000-sheet Finisher (Booklet Finisher) B674 • 3000-sheet Finisher B706. NOTE: The B674 requires installation of only the front spacer.
  • Page 53 PAGE: 46/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a Attaching the Extensions B470I003.WMF CAUTION Make sure that the finisher is disconnected from the main machine and that the machine is turned off and disconnected from the power outlet before you start the following procedure.
  • Page 54 PAGE: 47/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a Attaching the Interposer Tray Booklet Finisher B674 Only B470I004.WMF 1. If you install the cover interposer tray on the B674 finisher, install the spacer [A]. You will hear a click when it is installed correctly.
  • Page 55 PAGE: 48/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a Attaching the Corner Plates for the B706 The corner plates are installed on the B706 only. Attach the cover interposer tray to the finisher before you attach the corner plates.
  • Page 56 PAGE: 49/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a Right Front Corner Plate (B706 only) B470I008.WMF 1. Temporarily set the screw [A] (1 screw, M4 x 8) (with approximately two turns) to attach the panel at the right front corner.
  • Page 57 PAGE: 50/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a Attaching the Finisher to the Machine B470I005.WMF 1. Attach the sponge strip [A] (this is supplied with the finisher). NOTE: If you will install the cover interposer tray with a finisher that was installed on the machine before this time, remove the strip from the finisher and attach it to the cover interposer tray.
  • Page 58 PAGE: 51/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a 9. Switch on the machine, and select the default paper size for the cover interposer. IMPORTANT: Be sure to execute the correct SP code for the machine. Please refer to the table below.
  • Page 59 PAGE: 52/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a 9. 3000 Sheet Finisher (B706) Accessory Check Check the accessories and their quantities against this list: Description Q’ty 11. Cushion ................. 1 12. Table Extension..............1 13. Leveling Shoes..............1 14.
  • Page 60 PAGE: 53/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a B706I201A.WMF...
  • Page 61 PAGE: 54/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a B478I002.WMF B478I003.WMF B478I014.WMF B478I019.WMF Installation Procedure CAUTION Unplug the machine power cord before starting the following procedure. 1. Unpack the finisher and remove all tapes and shipping retainers.
  • Page 62 PAGE: 55/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a B478I004.WMF B478I005.WMF 0 ~ 2 mm 0 ~ 5 mm B478I107.WMF 5. Install the grounding plate [A] (2 screws, M3 x 6). NOTE: Set the grounding plate so that there is no gap between the grounding plate and the bottom frame of the finisher (as shown).
  • Page 63 PAGE: 56/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a B478I534.WMF B478I006.WMF 9. Attach the shift tray [A] (4 screws, M3 x 8). 10. Open the front door of the finisher, and remove the screw from the locking lever, then pull out the locking lever [B].
  • Page 64 PAGE: 57/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a When you move the finisher to a new location Before you move the finisher, do SP6107-003. This moves the mechanisms to their home positions. After you move the finisher, the mechanisms go back to the ready condition automatically,...
  • Page 65 PAGE: 58/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a 10. Punch Unit (B531/A812) The Punch Unit B531/A812 is installed in the 3000-Sheet Finisher B706. Accessory Check Check the accessories and their quantities against this list: B531I001.WMF Description Q’ty...
  • Page 66 PAGE: 59/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a B531I09.WMF B531I002.WMF Installation Procedure CAUTION Switch the machine off and unplug the machine before starting the following procedure. 1. If the finisher is connected to the machine, disconnect it.
  • Page 67 PAGE: 60/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a B531I004.WMF B531I003.WMF 7. Remove the paper guide [A] (4 screws). 8. Install the sensor arm [B] (1 screw, small step screw, M3 x 4). NOTE: Make sure that the sensor arm swings freely on the step screw.
  • Page 68 PAGE: 61/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a B531I006.WMF B531I005.WMF 10. At the front, secure the punch unit [A] with the large step screw (1 screw, M4 x 10). 11. At the rear, position the 2 mm spacer [B] and attach the punch unit [C] (2 screws, M4 x 10).
  • Page 69 PAGE: 62/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a B531I007.WMF B531I008.WMF 13. Connect the PCB harness connector [A] to CN129 of the finisher PCB and to CN600 of the punch unit PCB. 14. Connect the HP Sensor 2 harness connector [B] to CN130 of the finisher PCB and to HP Sensor 2.
  • Page 70 PAGE: 63/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a 11. Jogger Unit (B513) The Jogger Unit B531 is installed in the 3000-Sheet Finisher B706. Accessory Check Check the accessories and their quantities against this list: Description Q’ty 1.
  • Page 71 PAGE: 64/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a B513I001.WMF B513I002.WMF B513I003.WMF Installation Procedure 1. Turn the main machine switch off and disconnect the finisher from the main frame. 2. Use the flat head of a screwdriver to remove the left upper cover [A] from the finisher and discard it.
  • Page 72 PAGE: 65/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a 12. USB 2.0 interface Board (B596) Accessory Check Check the accessories and their quantities against this list: Description Q’ty 1. USB 2.0 Interface Board............1 Installation Procedure You can only install one of these cards, because only one PCI slot (B4) is available for these options: •...
  • Page 73 PAGE: 66/66 Reissued: 8-Apr-05 Model: Date: No.: Martini-P1 2-Mar-05 RG126002a 13. IEEE 802.11b Interface Unit (G813) Accessory Check Check the accessories and their quantities against this list: Description Q’ty 1. IEEE 802.11b Interface Board ..........1 2. WLAN PIC Card ..............1 3.
  • Page 74 PAGE: 1/1 Model: Date: No.: Martini-P1 8-Apr-05 RG126003 Subject: Prepared by: Firmware Release History (BCU - Engine) S. Watanabe From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision...
  • Page 75 PAGE: 1/1 Reissued: 04-Aug-06 Model: Date: No.: Martini-P1 8-Apr-05 RG126004d RTB Reissue The items in bold italics ha ve been added. Subject: Prepared by: Firmware Release History (Controller - System) S.Ishizu From: 2nd Tech Support Sec. Service Support Dept.
  • Page 76 PAGE: 1/1 Reissued: 23-Aug-06 Model: Date: No.: Martini-P1 8-Apr-05 RG126005d RTB Reissue The items in bold italics have been added. Subject: Prepared by: Firmware Release History (Printer) S. Watanabe From: 2nd Tech Support Sec. Service Support Dept. Troubleshooting...
  • Page 77 PAGE: 1/1 Reissued: 23-Aug-06 Model: Date: No.: Martini-P1 8-Apr-05 RG126006c RTB Reissue The items in bold italics have been added. Subject: Prepared by: Firmware Release History (NCS) S. Watanabe From: 2nd Tech Support Sec. Service Support Dept. Troubleshooting...
  • Page 78 PAGE: 1/1 Model: Date: No.: Martini-P1 12-Apr-05 RG126007 Subject: Prepared by: Firmware Release History (Netfile) S. Watanabe From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Paper path...
  • Page 79 PAGE: 1/1 Reissued: 3-Aug-05 Model: Date: No.: Martini-P1 12-Apr-05 RG126008b RTB Correction The items in bold italics have been corrected. Subject: Prepared by: Firmware Release History (WebSys) S. Watanabe From: 2nd Tech Support Sec. Service Support Dept. Classification:...
  • Page 80 RB140011 PAGE: 1/1 Reissued: 23-Aug-06 Model: Date: No.: Martini-P1 12-Apr-05 RG126009b RTB Reissue The items in bold italics have been added. Subject: Prepared by: Firmware Release History (DESS) S. Watanabe From: 2nd Tech Support Sec. Service Support Dept.
  • Page 81 CAUSE The Plug&Play setting for the MT-P1 machines for NRG (G126-22) produced in March '05 was mistakenly set to the value for the Ricoh model (G126-27). SOLUTION When these NRG machines are installed, we would like to ask that this setting (Sp5907- 001) be corrected from "0: Ricoh"...
  • Page 82 PAGE: 1/1 Model: Date: No.: Martini-P1 7-Mar-06 RG126011 Subject: Prepared by: ROM History (Finisher: SR841) S. Watanabe From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Paper path...
  • Page 83 echnical ulletin PAGE: 1/1 Reissued: 17-Feb-12 Model: Date: No.: MT-P1 8-Apr-05 RG126006d RTB Reissue The items in bold italics have been added. Subject: Prepared by: Firmware Release History (NCS) K. Yamamoto From: 1st Tech Service Sect., MFP/Printer Tech Service Dept. Troubleshooting Part information Action required...