Federal Signal Corporation Cuda TriOptic SIGNALMASTER 328823F Instruction Sheet

SAFETY MESSAGE TO INSTALLERS AND OPERATORS
People's lives depend on your safe instal-
lation of our products. It is important to
read, understand and follow all instructions
shipped with the products. In addition, listed
below are some other important safety in-
structions and precautions you should follow:
• To properly install this light, you must
have a good understanding of automotive
electrical procedures and systems, along
with proficiency in the installation and
use of safety warning equipment.
• DO NOT install equipment or route wir-
ing in the deployment path of an airbag.
• When drilling into a vehicle structure,
be sure that both sides of the surface are
clear of anything that could be damaged.
• In order for the light to function prop-
erly, a separate ground connection must
be made. If practical, it should be con-
nected to the negative battery terminal.
At a minimum, it may be attached to a
solid metal body or chassis part that will
provide an effective ground path as long
as the light system is to be used.
• Locate the light control so the VEHICLE
and CONTROL can be operated safely
under all driving conditions.
• Do not attempt to activate or deactivate
light control while driving in a hazardous
situation.
• This product contains high intensity LED
devices. To prevent eye damage, DO NOT
stare into the light beam at close range.
• You should frequently inspect the light to
ensure that it is operating properly and
that it is securely attached to the vehicle.
• File these instructions in a safe place and
refer to them when maintaining and/or
reinstalling the product.
Failure to follow all safety precautions and
instructions may result in property damage, serious
injury, or death to you or others.
A. GENERAL.
This unit is a multi-level rear deck LED warning light
designed for use in conjunction with Federal Signal Sig-
nalMaster controllers 330102, 330103, 331102, and Smart-
INSTRUCTION SHEET
Cuda TriOptic™ SIGNALMASTER™ LIGHT ASSEMBLY
MODEL 328823F
FOR
Siren® models with SignalMaster control. This device is
designed for mounting on a vehicle's interior only. The
housings are comprised of an extruded aluminum profile
with polycarbonate optic lenses. The metallic housing and
end cap material is of an anodized corrosion resistant alu-
minum.
B. UNPACKING.
After unpacking the kit and the light head, inspect
them for damage that may have occurred in transit. If
either the kit or the unit has been damaged, or missing a
part, do not attempt to install or operate it. File a claim
immediately with the carrier, stating the extent of dam-
age. Carefully check all envelopes, shipping labels and tags
before removing or destroying them. Ensure that all parts
in the following KIT CONTENTS LIST have been included.
C. KIT CONTENTS LIST.
Qty. Description
8 Screw, 1/4-20 x 7/16, Hex Head
6 Screw, Hex Hd, Type B, 5/8"
8 Nut, Hex, Ext Keps, 8-32
16 Lockwasher, Ext 1/4, Black
2 Bracket, Mounting
2 Bracket, Extension
2 Bracket, Swivel
D. INSTALLATION.
This product is intended for secondary warn-
ing and for use in conjunction with an ap-
proved primary warning light system.
When installing equipment inside air bag
equipped vehicles, the installer MUST ensure
that the equipment is installed ONLY in areas
recommended by the vehicle manufacturer.
Failure to observe this warning will reduce
the effectiveness of the air bag, damage the
air bag, or potentially damage or dislodge the
equipment, causing serious injury or death to
you or others.
1. See figure 1. Secure the swivel brackets to the
directional signal using the keps nuts supplied.
2. Assemble the extension brackets to the swivel
brackets using the 1/4-20 x 7/16" hex head machine screws
and external tooth lockwashers as shown. Ensure that a
lockwasher is installed between the brackets on each side
as shown. Do not tighten the screws at this time.
2562281A
REV. A 606
Printed in U.S.A.
Part No.
7000A232-07
7011165-10
7058A045
7075078A
8573054
8625181
8625184