Javad JLink LTE User Manual

Hide thumbs Also See for JLink LTE:

User manual (19 pages)

How to set up (4 pages)

How to set up (7 pages)

Table Of Contents

Table of Contents

Quick Links

Download this manual

JLink LTE

User Manual

Version 1.2

Last Revised July23, 2020

All contents in this manual are copyrighted by JAVAD GNSS.

stored, displayed, sold, modified, published, or distributed, or otherwise reproduced without express

written consent from JAVAD GNSS.

Table of Contents

Need help?

Do you have a question about the JLink LTE and is the answer not in the manual?

Questions and answers

Summary of Contents for Javad JLink LTE

Page 1 Version 1.2 Last Revised July23, 2020 All contents in this manual are copyrighted by JAVAD GNSS. All rights reserved.The information contained herein may not be used, accessed, copied, stored, displayed, sold, modified, published, or distributed, or otherwise reproduced without express...
Page 3: Table Of Contents
Table of Contents ...Setup JLink LTE to provide RTK data received via Preface ............5 NTRIP Client to Serial Port Terms and Conditions ........5 ...Setup JLink LTE to provide RTK data received via UHF channel (in Satel mode) to Serial Regulatory Information.........
Page 4 www.javad.com...
Page 5: Preface
JAVAD GNSS products. It is designed INCIDENTAL CONSEQUENTIAL DAMAGES to assist owners with the use of JLink LTE and its use RESULTING FROM THE FURNISHING, PERFORMANCE is subject to these terms and conditions (the “Terms OR USE OF THIS MATERIAL OR THE JLINK LTE. SUCH and Conditions”).
Page 6: Regulatory Information
Any changes or modifications to the equipment SAFETY – Improper use of JLink LTE can lead to in- not expressly approved by the party responsible for jury to persons or property and/or malfunction of the compliance could void your authority to operate such product.
Page 7: Technical Assistance
If you have a problem and cannot find the informa- tion you need in the product documentation, contact your local dealer. Alternatively, request technical sup- port using the JAVAD GNSS World Wide Web site at: www.javad.com To contact JAVAD GNSS Customer Support use the QUESTIONS button available on the www.javad.com.
Page 8: Description And Operation
GNSS equipment to RTN, where no cell phone cover is available. JLink LTE devices may contain 1 W either JLink LTE is a family of devices designed for or- UHF (406 to 470 MHz) or VHF (138-174 MHz), or ISM...
Page 9: Installation
• via Bluetooth interface: the device (PC, hand- held/pad) should be with Bluetooth interface with PAN profile support. JLink LTE Bluetooth-interface is in visibility mode, has the name “Jlink LTE” and PIN code 0000. When connection is established open the web-browser and enter the address 10.1.11.1:8080.
Page 10 Status/ in device label. For connecting to JLink LTE serial GSM tab see below. port needed to setup with following parameters: • Baudrate 115200 • Parity none • Data Bits 8 • Stop Bits 1 •...
Page 11: How
• In the Communication/Power Management tab received via NTRIP Client to Serial Port activate the GSM interface. 1. Connect to JLink LTE via web interface as de- scribed above. 2. Configure the Cellular (GSM ): • In the Communication/GSM tab set the PIN code and APN parameters (if necessary);...
Page 12 GSM Status tab Figure 11. It is possible also to connect JLink LTE to Internet via LAN or WiFi using any WiFi router, MiFi device or even smartphone configured in hot spot mode. 3. Set up the Serial Port. In the Communication/ Advanced tab select “Serial port as”...
Page 13 Figure 16. Status NTRIP tab 7. Connect the Serial Port. Use any application to connect serial port of JLink LTE with following param- Figure 15. NTRIP configuration tab eters: • Click Save Settings and wait until finish. • Baudrate 115200 •...
Page 14: Setup Jlink Lte To Provide Rtk Data Received Via Uhf Channel (In Satel Mode) To Serial Port
...Setup JLink LTE to provide RTK data received via UHF channel (in Satel mode) to Serial Port 1. Connect to JLink LTE via web interface as de- scribed above. 2. UHF configuration in Satel mode: • In the Communication/UHF Int. tab: •...
Page 15 4. Reboot the device by clicking Reboot in the Administration/Management tab. Figure 22. UHF Modem Router tab 6. Connect the Serial Port. Use any application to connect serial port of JLink LTE with following param- eters: • Baudrate 115200 •...
Page 16: Configure Triumph-2 And Jlink Lte To Provide Triumph-2 Services Through Internet
10.1.10.120. To receive the redirected data of JLink Internet LTE the TRIUMPH-2 receiver should be connected to In this configuration JLink LTE will share its Internet JLink LTE through WiFi interface and TRIUMPH-2’s IP address should be set 10.1.10.110 or 10.1.10.120.
Page 17 IP Address (10.1.10.120), WLAN Default Gateway (e.g, 10.1.10.1), and WLAN Network Mask (e.g, 255.255.255.0). • Set the AccessPoint parameters: WLAN Ac- cess Point ID (enter SSID of JLink LTE), WLAN AP mode(wpa). • Set the WPA parameter: WLAN WPA Passphrase (enter passphrase of JLink LTE).
Page 18: Update Firmware Of Hpt435Bt Jl
DHCP (see Picture • Apply settings clicking “save settings” button. Figure 31. Management tab ...Setup JLink LTE internal GNSS module Connect to Jlink LTE via web interface. If using GNSS “Base” or “Assisted” modes is necessary to insert the SIM card. GSM/GNSS...
Page 19 Figure 33. Power Management tab The detailed connection status can be checked in the Status/GSM tab (see picture below): Figure 35. GNSS Status tab JLink LTE GSM. Status tab Figure 34. The detailed status of the GNSS module can be www.javad.com...
Page 20: Setup Jlink Lte With External Gnss Via
...Setup JLink LTE with external GNSS via network Connect to Jlink LTE via web interface. Setup the External GNSS path (IP address and PORT). • In the Communication/Advanced tab set the cor- rect path of the GNSS module (parameter Net GPS IP: PORT see at the picture below.)
Page 21: Setup Jlink Lte Ethernet Bridge
...Setup JLink LTE Ethernet Bridge ...Setup JLink LTE to provide UHF Repeater functionality 1. Connect to Jlink LTE via a web interface. 1. Connect to Jlink LTE via a web interface. 2. Setup the Ethernet as a Bridge. UHF configuration in Javad protocol: Reboot the device from Administration/Management tab.
Page 22 Figure 40. Power Management tab The detailed connection status can be checked in the Status/UHF tab (see picture below): Figure 42. Routing tab Figure 41. UHF Int. Status tab Make sure, UHF is not used on Setup/Routing tab. www.javad.com...
Page 23: Setup Jlink Lte With Gyndns Client
...Setup JLink LTE with GYNDNS Client Connect to Jlink LTE via web interface (For more detail see document “JLink LTE User Manual”). Setup DYNDNS Client: • In the Services/DYNDNS tab set correct configu- ration parameters (parameters are user, password and host name see picture 1.) •...
Page 24: Specifications
Transmitter Output 1W (+30 dBm) Data Rate of Radio Interface Power 64000 bps (USA/Australia) Communication Half duplex, simplex, repeater Data Rate Radio Interface (EU) 9600 bps Mode Transmitter Output Power 1W (+30 dBm) Communication Mode Half duplex, simplex, repeater www.javad.com...
Page 25 ** The storage temperature range of Li-Ion batteries is -20 ° C to 3.6Amax +60° C Battery (optional) One embedded, 7.2V, 5850 mAh Pinout of JLink LTE power and communication port Pin # Signal Name I/O Description Pin # Signal Name I/O Description...
Page 26 1- UHF/VHF/ISM Transceiver / Beacon receiver, cellular module, GPS receiver, Bluetooth, WiFi, Ethernet, USB and Serial port. 2 - Variant 1 with battery. 3 - Cellular module, GPS receiver, Bluetooth, WiFi, Ethernet, USB and Serial port. 4 - Variant 3 with battery. www.javad.com...
Page 27: Safety Warnings
Without proper safeguards at the measuring site. • Contrary to applicable laws, rules, and regula- tions. Warning: The JLink LTE receiver should never be used in dangerous environments. Use in rain or snow for a limited pe- riod is permitted. www.javad.com...
Page 28: Warranty Terms
Manual. The equipment is guaranteed for the period indicated, on the warranty card accompany- ing the product, starting from the date that the prod- uct is sold to the original purchaser by JAVAD GNSS’ Authorized Dealers. During the warranty period, JAVAD GNSS will, at its option, repair or replace this product at no additional charge.

Javad JLink LTE User Manual

Quick Links

Need help?

Questions and answers

Related Manuals for Javad JLink LTE

Summary of Contents for Javad JLink LTE

Table of Contents